IsoLux IsoLED Plus User Manual

IsoLux llc, 1045 Collier Center Way, Naples, Florida USA 34110 phone: [phone] fax: [phone]

email: [e-mail] web: www.isoluxllc.com

2.0 Operating Instructions

2.1 Charging the Battery

1. Plug the charger’s male connector into the

receptacle on the Battery Pack.

2. Plug the AC connection into a 100-240 VAC

source.

3. The charger indicator light will illuminate red

while charging and turn green when charging is
complete (approximately 3.6 hours).

4. An 85% partial charge may be performed in 2

hours.

5. Disconnect the charger from the AC source and

unplug the charger from the control unit.

2.2 Illuminator and Headband Operation

1. Plug the Cable Assembly into the illuminator

unit receptacle. There are red orientation dots
that must be aligned.

2. The cable should be routed and snapped into

place through a set of two cable clips. For dual
ratchet headsets one is located on the top on
the crown and one on the rear of the headband.
The user has the choice of using the set on the
left or the right.

3. For softband/Velcro headsets, the cable should

be routed through two clips along the
circumference.

4. The illumination spot size may be adjusted by

turning the grooved dial on the headlight.

5. The linkage assembly on the headband allows

for personal positioning control. The joystick is
used to further adjust the position of the light
beam.

2.3 Control Unit / Battery Pack Operation

1. Assure the Cable Assembly is plugged into the

illuminator unit receptacle. There are red
orientation dots that must be aligned.

2. Plug the other end of the Cable Assembly into

the Control Unit/ Battery Pack receptacle, once
again aligning the red dots.

3. Clip the control unit where desired or place in a

pocket.

4. Turn the ON/OFF and intensity control knob

clockwise to turn unit On (switch will close).
This knob also controls the intensity.

5. To turn unit Off, turn control knob counter-

clockwise until switch opens.

6. When battery has discharged to a level too low

to maintain operation, the Illuminator will dim

IsoLED Plus

HEADLIGHT

User’s Guide

1.0 Purpose and Features of the product

1.1 Purpose

The headlight is used for examination, diagnostics
and surgical operations for multifarious uses
including microsurgery.

1.2 Features

• 50,000 hours of LED life provides for a

maintenance free device with an end life of
approximately 20 years.

• The unit has infinite mobility, not confined by

access to power sockets, and its charge will last
more than 3 1/2 hours at full intensity.

• Its light beam is extremely homogeneous and

free of imperfections.

• Its high CRI rating of 96 is very desirable in

color-critical applications such as neonatal care,
medicine and surgery, as it shows the true
colors of tissues and skin, thereby reducing the
time to diagnosis and surgery.

• The light-weight battery packs have a retention

clip to be used on the user’s belt or pocket.

• The wall mounted Battery Charger comes with a

Charge Monitor that alerts the operator when
the Battery is fully charged.

• The unit comes with two (2) Battery Packs,

allowing for “Hot Swap” and the extension of its

operating time to > 7 hours.

IsoLux llc, 1045 Collier Center Way, Naples, Florida USA 34110 phone: [phone] fax: [phone]

email: [e-mail] web: www.isoluxllc.com

or flicker and the green LED on the control
panel will turn off.

7. The unit’s operational time could be extended

from 3½ hours at full intensity to greater than 7
hours by using the illuminator at half intensity.

3.0 SPECIFICATIONS

4.0 Battery use and care

The capacity of Li-ion rechargeable batteries will be
changed by its’ environmental temperature. The
appropriate temperature is (10 ℃~40 ℃) range. Do not
expose the battery to extreme temperatures, if the
battery is used in high or low temperatures, the battery
capacity will be reduced.
Dispose of worn battery safely.

5.0 Care and Maintenance

5.1 Headlight, Headgear and Cable
Exterior surfaces of headlight, headgear and cable

can be wiped clean with 10% bleach, 70% isopropyl

alcohol or Mild soap.
Headbands and headlight modules cannot be

immersed into disinfecting liquids or sterilizers.
Keep ends of cable clean by wiping with a damp cloth.

Allow to dry before use.
Clean the optics only with lens tissue available at any

camera store. Follow the instructions on the
package.

To insure long life for the headgear, cable and power
source, store them in a cool dry environment.

5.2 Joystick

Joystick can be sterilized after unscrewing from
headlight.

DO NOT AUTOCLAVE ANY OTHER PARTS OF
THE HEADLIGHT SYSTEM !

6.0 Warnings and Cautions

6.1 Warnings

Users of this headlight should be trained in the
appropriate surgical procedures.

They should read and understand the owner’s manuals

for this Headlight and all equipment used in conjunction
with it.

Warning: This product must not be used in the
presence of flammable gases.

Warning: This product should not be immersed in

fluids.

Warning: Do not shine the light directly into the
patient’s eyes.

9.0 List of Spare Components

Item

Qty.

Description

Part No.

1 1 Battery Pack

IL-2295

2 1 Headlight Illuminator

IL-2298

3 1 Headlight Cable Ass’y

IL-2348

4 1 Sweatbands (pack of 4 sets)

IL-2297

5 1 Battery Charger

IL-2187

6 1 Joystick (pack of 2)

FO-0911

7 1 Replacement Head Gear

FO-2072

Illumination

> 31,000 lux @ 30 cm

LED Life

>50,000 hours

Color Temperature

4,500 °K

Color Rendition

Index (CRI)

96 Typical

Light Degradation

None

Spot Size

10 to 100 mm @ 400 mm
working distance

Intensity Range

20% to 100%

Operating Time

>3.5 hours typical at
maximum intensity

Normal Recharge

Time

3.6 hours

Quick Recharge

Time

2 hours, for 3 hours of
maximum intensity

Battery Charger

Universal: 100 to 264 VAC,
50 to 60 Hz.,8.4 VDC @ 1.3 A

Weight (headlight)

290 grams

Weight (Battery

Pack)

190 grams

Size (control

unit/battery pack)

4.25” x 2.7” x 1.1”