iSolution DMX512 575W Plus User Manual

User Guide

Please read these instructions carefully before use

1C

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. Lamp

4. How To Set The Unit

4.1 Control Panel

4.2 Main Function

4.3 Home Position Adjust

5. How To Control The Unit

5.1 Master/Slave Built-In Preprogrammed Function

5.2 Easy Controller

5.3 iSolution Operation / DMX Controller

5.4 DMX 512 Configuration

5.5 DMX 512 Connection

6. Troubleshooting

7. Maintenance and Cleaning

2C

1. Safety Instruction

WARNING

z Please keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

z Unpack and check carefully there is no transportation damage before using the unit.
z Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

z The unit is designed for use with the HMI 575W, HMQ 575/2 lamps. Do not use any other

type of lamp.

z It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

z The unit is for indoor use only. Use only in a dry location.
z The unit must be installed in a locatio n with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

z Disconnect main power before fuse/lamp replacement or servicing.
z Replace fuse/lamp only with the same type.
z Make sure there are no flammable materials close to the unit while operating, as it is fire

hazard.

z Use safety chain when fixes this unit. Don’t handle the unit by taking its head only, but

always by taking its base.

z Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is

higher than this.

z Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during

its operation, and allow about 15 minutes to cool down before replacing bulb or serving,
as the unit could be very hot.

z In the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center. Always
use the same type spare parts.

z Don’t connect the device to any dimmer pack.
z Do not touch any wire during operation as high voltage might be causing electric shock.

Please read carefully the instruction, which includes important

information about the installation, usage and maintenance.

3C

Warning

z To prevent or r educe the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

z Never touch bulb with bare fingers, as it is very hot after using.
z Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.
z Do not start on the unit without bulb enclosure or housing are damaged.
z The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

z Do not look directly at the light while the bulb is on.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt any
repairs by yourself. In the unlikely event your unit may require service, please contact yo ur
nearest dealer.

Installation

The unit should be mounted via its screw holes on the bracket (please refer to the drawing
below). Always ensure that the unit is firmly fixed to avoid vibration and slipping while
operating. Always ensure that the structure to which you are attaching the unit is secure and
is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable
that can hold 12 times of the weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out
of the touch of people and has no one pass by or under it.

4C

2. Technical Specification

Power supply

-

AC 120V~60Hz or AC 230/240/250V~50/60Hz

Lamp

-

HMI 575W / HMQ 575/2 lamp base:SFc10-4

Optical system

- High efficiency optical system

- High quality optical lens and dichroic colors

- Beam angle: 14°

Shutter/Dimmer

- Blackout, 0~100 smooth dimming and strobe speed

variable(1~10 flashes per

second).

Color wheel

- Independent color wheel with 9 trapezoid

dichroic colors plus white.

- Color wheel rotates with variable speed, giving rainbow effect.

Gobo wheel

- Independent gobo wheel with 9 replaceable gobos

plus open.

- Independent gobo wheel with 7 rotating, replaceable gobos

plus open.

Effect Wheel

- Prism/Rotating Prism

Movement

- Pan: 540° in 2.8 second.

- Tilt: 270° in 1.6 second.

DMX Channels

- Standard DMX 512 signal addressing and can be controlled by any universal DMX
controller.

16 Channels:

Channel 1 = Pan Channel 9 = Gobo 2
Channel 2 = Tilt Channel 10 = Gobo 2 Rotation
Channel 3 = Pan/Tilt Speed select Channel 11 = Prism
Channel 4 = Dimmer Channel 12 = Prism Rotation
Channel 5 = Shutter/Shaking Channel 13 = Focus
Channel 6 = Color Channel 14 = Pan 16 bit
Channel 7 = Iris Channel 15 = Tilt 16 bit
Channel 8 = Gobo 1 Channel 16 = Reset/Lamp on/off

5C

8 Channels: Luminous intensity:

Channel 1 = Pan
Channel 2 = Tilt
Channel 3 = Shutter
Channel 4 = Gobo
Channel 5 = Color
Channel 6 = Gobo Rotation /

Iris

Channel 7 = Prism/Prism

Rotation/Dimmer

Channel 8 = Focus

Dimension: 428 x 369x 478 mm (L x W x H)

Weight: 28.5 kg

2.1. Inserting/Exchanging rotating gobos

DANGER!

Install the gobos with the device switched off only.

Unplug from mains before changing gobos!

Open the cover by loosening the fastening screw at the sides of the cover.
If you wish to use other forms and patterns as the standard-gobos, or if the gobos are to be
exchanged, remove the fixation ring with an appropriate tool. Remove the gobo and insert
the new gobo. Press the fixation-ring together and insert it in the front of the gobo.

6C

CAUTION!

Never unscrew the screws of the rotating gobo as the ball bearing

will otherwise be opened!

3. Lamp

Because of its high internal pr essure, there might be a risk that the Discharge lamp
would explode during operation. The lamp emits intense UV radiation which is harmful
to the eyes and skin. The high luminance of t he arc can cause severe damage to the
retina if looks directly at the lamp.

HMI 575W / HMQ 575/2 SFc10-4

1. Always switch off the main supply and never handle the lamp or luminaire when it is
hot.

2. Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured
alcohol and wipe it with a lint free cloth before installation.

3. The lamp generates UV radiation. Never operate the lamp without appropriate shielding.

4. When burning, the lamp operates at high pressure and there is a slight risk of arc tube
rupture. The risk increases with age, temperature and improper handling of the lamp. Do
not use the lamp any longer than its specified life.

5. Make sure the lamp is located in the center of the reflector for the best spot.

In case of replacement of the lamp or maintenance, do not open the
fixture within 15 minutes until the unit cools down after switching off.

7C

4. How To Set The Unit

4.1. Control Panel

Display

To show the various menus and the selected functions .

LED

8C

DMX On DMX input present
MASTER On Master mode
SLAVE On Slave mode
SOUND Flashing Sound activation

Button

MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions

Remote controller input

By connecting to the 1/4” microphone jack to control the unit for Stand by, Function, and
Mode function.

Sensitivity

To adjust the sound-receiving sensitivity .

DMX input/output

For DMX 512 link, use 3-pin XLR plug cable to link the unit together.

4.2. Main Function

To select any of the pre-set functions, press the MENU button up to when the required one
is shown on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
press the ENTER button to setup or it will automatically return to the main functions without
any change after idling 8 seconds. To go back to the functions without any change press the
MENU button. The main functions are shown below:

9C

DMX 512 Address Setting

Press the MENU button up to when the

is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press the ENTER button to setup or automatically
return to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.

Channel Mode

Press the MENU button up to when the is shown on the display.
Pressing ENTER button and the display will blink. Use DOWN and UP button

to select the

(16 Channel ) or (8 Channel) mode. Once the
mode has been selected, press the ENTER button to setup or automatically
return to the main functions without any change after 8 seconds. To go back to

10C

the functions without any change press the MENU button again.

Show Mode

Press the MENU button up to when the

is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (show 1)
or

(sho w 2) or (show 3) or (show 4) mode. Once the mode has

been selected, press the ENTER button to setup or automatically return to the main
functions without any change after 8 seconds. To go back to the functions without any
change press the MENU button again.

Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.

Show 3 mode - Fixture is placed on the speaker, The spot is always projecting

to the audience’s direction; i.e in front of the stage. Pan movement angle ( left to

right to left ): 160°. Tilt movement angle: 90° ( 60° above horizon; 30° below horizon).

Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in front of

the stage. Pan movement angle ( left to right to left ) :160°. Tilt movement angle:
90° ( vertically, front 75°; back 15° ) .

Slave Mode

Press the MENU button up to when the

is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (normal)
or

(2 light show) mode. Once the mode has been selected, press the ENTER

button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.

Blackout Mode

Press the MENU button up to when the

is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the

(yes

blackout) or

(no blackout) mode. Once the mode has bee n selected, press the

ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button

11C

again.

Pan Inversion

Press the MENU button up to when the

is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the

(normal)

or

(pan inversion) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.

Tilt Inversion

Press the MENU button up to when the

is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the

(normal)

or

(tilt inversion) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8

seconds. To go back to the functions without any change press the MENU button again.

Led Display

Press the MENU button up to when the

is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(Led on) or

(Led off) mode. Once the mode has been selected, press the ENTER

button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.

Display Inversion

It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
when the is blinking on the display. Use the ENTER button to change to the mode

(display inver sion), It will automatically store after 8 seconds. Or press the ENTER

button again return to the mode (display normal). To go back to the functions press
the MENU button.

Display normal mode for the fixture putting on the floor.
Display inversion mode for the fixture fixing under ceiling.

Gobo1 focus Adjust

Press the MENU button up to when the is blinking on the display. Pressing ENTER

12C

button, the unit will focus on tilt 135°, and then the unit will first focus on tilt 45°, pan 0°, pan
90°, pan 180°, pan 270° each time your press ENTER button. Use DOWN and UP button to
adjust fixable gobo wheel focus. To go back to the functions press the MENU button again.

Gobo2 focus Adjust

Press the MENU button up to when the is blinking on the display. Pressing ENTER
button, the unit will focus on tilt 135°, and then the unit will first focus on tilt 45°, pan 0°, pan

90°, pan 180°, pan 270° each time your press ENTER button. Use DOWN and UP button to
adjust rotating gobo wheel focus. To go back to the functions press the MENU button again.

Self-Test

Press the MENU button up to when the

is blinking on the display. Pressing ENTER

button and the unit will run self-test by built-in program. To go back to the functions press the
MENU button again.

Ambient temperature of lamp

Press the MENU button up to when the is blinking on the display. Pressing ENTER
button and the ambient temperature of lamp will show on the display. To go back to the

functions press the MENU button again.

Fixture Hours

Press the MENU button up to when the

is blinking on the display. Pressing ENTER

button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button again.

Lamp ON/OFF

Press the MENU button up to when the

is blinking on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the

(Lamp on)

or (Lamp off) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To

go back to the functions without any change press the MENU button again.

Power ON/OFF

Press the MENU button up to when the is blinking on the display. Pressing

13C

ENTER button and the display will blink. Use DOWN and UP button to select the
(power on) or

(power off) mode. Once the mode has been selected, press the

ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.

Reset

Press the MENU button up to when the

is blinking on the display. Pressing ENTER

button and all channels of the unit will return to their standard position. To go back to the
functions press the MENU button again.
DMX RESET :
Set DMX value of channel 16 to 200~209, then all channels of the unit will return to their
standard home position after about 5 seconds.

4.3 Home Position Adjust

Press MENU button for at least 5 seconds into offset mode to adjust the home position,
when you want to adjust gobo and color home position, you should be run mode

first , the functions are shown below:

Pan offset

Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button
up to when the is shown on the display. Pressing ENTER button and the display

will blink. Use DOWN and UP button to adjust the pan home position. Once the position has
been selected, press the ENTER button to setup or automatically return to the offset

14C

functions without any change press the MENU button again, To go back to the main
functions without any change after 8 seconds.

Tilt offset

Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button
up to when the is shown on the display. Pressing ENTER button and the display

will blink. Use DOWN and UP button to adjust the tilt home position. Once the position has
been selected, press the ENTER button to setup or automatically return to the offset
functions without any change press the MENU button again, To go back to the main
functions without any change after 8 seconds.

Focus Adjust

Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button
up to when the

is shown on the display. Pressing ENTER button, the unit will focus

on tilt 135°, and then the unit will first focus on tilt 45°, pan 0°, pan 90°, pan 180°, pan 270°
each time your press ENTER button. Use DOWN and UP button to adjust focus, this
settings only for offset mode to adjust home position. To go back to the main functions
without any change after 8 seconds .

Dimmer offset

Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button
up to when the

is shown on the display. Pressing ENTER button and the display

will blink. Use DOWN and UP button to adjust the dimmer home position(0~255). Once the
mode has been selected, press the ENTER button to setup or automatically return to the
offset functions without any change press the MENU button again, To go back to the main
functions without any change after 8 seconds.

Gobo 1 offset

Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button
up to when the

is shown on the display. Pressing ENTER button and the display

will blink. Use DOWN and UP button to adjust the gobo home position. Once the gobo 1 has
been selected, press the ENTER button to setup or automatically return to the offset

15C

functions without any change press the MENU button again, To go back to the main
functions without any change after 8 seconds.

Gobo 2 offset

Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button
up to when the is shown on the display. Pressing ENTER button and the display

will blink. Use DOWN and UP button to adjust the gobo home position. Once the gobo 2 has
been selected, press the ENTER button to setup or automatically return to the offset
functions without any change press the MENU button again, To go back to the main
functions without any change after 8 seconds.

R-gobo offset

Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button
up to when the

is shown on the display. Pressing ENTER button and the display will

blink. Use DOWN and UP button to adjust the R-gobo home position. Once the R-gobo has
been selected, press the ENTER button to setup or automatically return to the offset
functions without any change press the MENU button again, To go back to the main
functions without any change after 8 seconds.

Color offset

Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button
up to when the is shown on the display. Pressing ENTER button and the display

will blink. Use DOWN and UP button to adjust the color home position. Once the color has
been selected, press the ENTER button to setup or automatically return to the offset
functions without any change press the MENU button again, To go back to the main
functions without any change after 8 seconds.

16C

5. How To Control The Unit

You can operate the unit in three ways:

1. By master/slave built-in preprogram function

2. By easy controller

3. By IL-0824 ( only for setting in 8 channel mode, please refer to the user gui de of iLead
controller ) or by universal DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address
setting will be effected at once. Every time you turn the unit on, it will show 575 on the
display and move all the motors to their ‘home’ position and you may hear some noises for
about 20 seconds. After that the unit will be ready to receive DMX signal or run the built-in
programs.

5.1. Master/Slave Built-In Preprogrammed Function

You can select blackout mode

in (yes blackout) or (no blackout)

mode while the unit is turned on. By linking the units in master/slave connection, the first unit
will control the other units to give an automatic, sound activated, synchronized light show.

This function is good when you want an instant show. You have to select

(show 1)

or

(show 2) or (show 3) or (show 4) mode by easy co nt roller. Its

DMX input jack will have nothing plugged into it, and Its master LED will be constantly on
and sound LED will flash to the music. The other units will have to set in slave mode

and select (normal) or (2 light show) mode, Their DMX cables

plugged into the DMX input jacks (daisy chain) and the slave LED lights will constantly on.

2-light show

In

(slave mode), means the unit works normally and means

2-light show. In order to create a great light show , you can set

on the second unit to

get contrast movement to each other, even if you have two units only.

5.2. Easy Controller

The easy remote control is used only in master/slave mode. By
connecting to the 1/4” microphone jack of the first unit, you will find that
the remote control on the first unit will control all the other units for Stand
by, Function and Mode.

17C

Stand by Blackout the unit

Function

Strobe

1. Color sync. strobe

2. Sync. strobe

3. Two-light strobe

X/Y moving show pattern
selection
( Show 1 ~ Show 4 )
Please refer to 4.2. Main
Functions- Show mode

Gobo/Color
selection

1.Hold on for gobo
selection

2.Press for color
change

X/Y moving setting

1.Pan position

2.Tilt position

3.Dimmer
First set Master unit, then set Slave
units’ position

Mode

Sound 1
(LED off )

Sound 2
(LED slow blinking)

Slow/Sound 3
(LED on)

Position/ Latch
(LED fast blinking)

5.3.1 iSolution Operation

·Consistent DMX configuration enable iMove to be linked with iRock and iSho w together
and controlled at the same time.

·DMX address can be set remotely by iLead controller ( please refer to the user manual of
iLead controller ). No need to calculate the DMX channels of each fixture in the chain.

·Automatic switching between DMX function and built-in stand alone programs.

5.3.2 DMX Controller

If you use a universal DMX controller to control the units, you have to set DMX address from
1 to 512 channel so that the units can receive DMX signal.

Press the MENU button up to when the is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX 512 address.

Once the address has been selected, press and keep ENTER button pressed up to when
the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again.
Please refer to the following diagram to address your DMX 512 channel for the first 4 units.

16 Channels：

8 Channels：
You have to set the fixture DMX address in 8 channels mode when you use IL-0824

controller. DMX address can be set remotely by IL-0824 controller. No need to calculate the
DMX channels of each fixture in the chain.
Please refer to the following diagram to address your DMX 512 channel for the first 4 units.

8 Channels：

18C

5.4. DMX 512 Configuration

i.) The value as below will be effected after about five seconds,

For DMX reset, put DMX value of CH-16 to 200-209
For DMX lamp on, put DMX value of CH-16 to 130-139.
For DMX lamp off, put DMX value of CH-16 to 230-239.

19C

20C

5.5. DMX 512 Connection

The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels.

1. If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pin adapter.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in
the DMX-output of the last unit.

3. Connect the unit together in a “daisy chain” by XLR plug from the output of the unit to the
input of the next unit. The cable cannot be branched or split to a “Y” cable. DMX 512 is a
very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
connectors can easily distort the signal and shut down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX circuit,
when power is disconnected to the unit.

5. Each lighting unit needs to have an address set to receive the data sent by the controller.
The address number is between 0-511 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

21C

6. Troubleshooting

Following are a few common problems that may occur during operation. Here are
some suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connect power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and DMX
polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of
the unit or the previous one.

4. Try to use another DMX controller.

5. Check in the DMX cables run near or run alongside to high voltage cables that may cause
damage or interference to DMX interface circuit.

C. Some units don’t respond to the easy controller

1. You may have a break in the DMX cabling. Check the LED for the response of the master/
slave mode signal.

2. Wrong DMX address in the unit. Set the proper address.

D. No response to the sound

1. Make sure the unit that is not receiving DMX signal.

2. Check microphone to see if it is good by tapping the microphone.

E. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition.

F. The lamp is cutting out intermittently

1. The lamp is not working well. Check the main voltage either too high or too low.

2. Internal temperature may be too high. Check and if necessary replace the fan on the head.

G. If The pan belt is broken

22C

1. Turn off the main power.

2. Unscrew all the screws (A) and open the base-housing cover (B).

3. Unscrew all the screws (C) and open the arm cover (D).

4. Unplug all the connect wires that from the arm to the bottom.

5. Unscrew the screws (E) and remove the fixture head.

6. Loose the screws (F), then loose the screws (G).

7. Change a new belt (H) , put the belt around the axis gear and motor gear.

8. Screwed the screws (G), install the new belt and adjust the belt tension properly. Note: it is
too tight to rupture.

9. Plug all the connect wires back that form the bottom to the arm.

10. Reverse the procedures from point 5 to point 2.

A

B

A

B

C

D

C

D

E

F

H

G

A

H. If The tilt belt is broken

23C

1. Turn off the main power.

2. Unscrew all the screws (A) and open the right arm cover (B).

3. Unscrew the screws (C), the screws (D) and screws (E) that fix the bridge.

4. Change a new belt (F). Please adjust the tension of the belt properly. Note: it is too tight to
rupture.

5. Reverse the procedures from point 3 to 2 .

A

B

C

C

E

D

C

F

24C

Pay attention to the belt tension when install the belt.

Please refer to the photos below:

F

G

Photo 1

Adjust belt tension through loose the screw

Photo 2

25C

7. Maintenance and cleaning

Maintenance:

Connector Ballast

Filter, Capacitor

Ignitor, Anti-interfe rence plate

A. As the pictures shown above, if the cable or cable joints turned yellow or black, please

replace the cable or cable joints immediately.

B. Do maintain the fixtures every two months and make sure that all the screws and

terminals have been locked firmly to make sure the normal performance of the fixtures.
Negligence of maintenance would cause malfunction of the fixture.

Cleaning:

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.

y Clean with soft cloth using normal glass cleaning fluid.
y Always dry the parts carefully.
y Clean the exte rnal optics at least every 20 days. Clean the internal optics at least every

30/60 days.

26C

EC Declaration of Conformity

We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
EN61000-4-11: 1994.

&

Harmonized Standard

EN60598-1: 2000+ALL:2000+A12:2002
Safety of household and similar electrical appliances
Part 1 : General requirements

27C

Innovation , Quality , Performance