iSmarGate 01W Instructions For Use Manual

Download

iSmartGate-01W

INSTALLATION MANUAL iSmartGate 01W

ENGLISH· REV.3

www.v2fe.com

GARAGE CONTROL PANEL

LED STATUS

LED OUTPUT 1

LED OUTPUT 2

P. E N L

110/220AC

SEL BACK OK

RELAY 1 RELAY 2

Wi-Fi

iSmartGate-01W

www.v2fe.com

TABLE OF CONTENTS

1. iSmarGate-01W Instructions for use....................................................................................

1.1 Quick Starter....................................................................................................................

1.2 Safety Instructions............................................................................................................

1.3 Examples of use of the application...................................................................................

2. Wiring the iSmartGate-01W ................................................................................................

2.1 Wiring supply power ........................................................................................................

2.2 Wiring Load .....................................................................................................................

2.2.1 iSmartGate GARAGE Mode Wiring........................................................................

2.2.2 iSmartGate PULSE Mode Wiring..........................................................................

2.23 iSmartGate ON/OFF Mode Wiring.......................................................................

3. 3. Network........................................................................................................................

3.1 Step 1: Connecting your iSmartgate-01W to the Wi-ﬁ router or AP....................................

3.2. Step 2: Find the iSmartgate-01W on your LAN network...................................................

3.3. Step 3: iSmartgate-01W network options conﬁguration...................................................

3.3.1 SSID Conﬁguration............................................................................................

3.3.2 Wi-ﬁ Security Settings Conﬁguration..................................................................

3.4 Step 4: AP / Wi-Fi router Conﬁguration............................................................................

3.5. Step 5: Veriﬁcation.........................................................................................................

3.6. Troubleshooting Guide..................................................................................................

4. How it works...................................................................................................................

4.1 GateName, Password, Port, Ipcast and Working Mode conﬁguration.................................

4.2 GateName conﬁguration................................................................................................

4.3. Password Conﬁguration..................................................................................................

4.4. Working Mode Conﬁguration..........................................................................................

4.5. Port Conﬁguration..........................................................................................................

4.6. IP Broadcast Conﬁguration.............................................................................................

4.7. Network Factory Default.................................................................................................

5. Upgrade Firmware............................................................................................................

6. iSmartgate App conﬁguration .........................................................................................

6.1 How to add a door........................................................................................................

6.2 App Options...................................................................................................................

3 3 4 5

6 6 7 7 9

11 12 13 14 14 15 16 16 17

18 18 19 19 20 20 21 23

26 27 29

1. iSmarGate-01W Instructions for use

iSmartGate-01W

www.v2fe.com

1.1 Quick Starter

-Wire up iSmartGate01W to our garage control panel. See section 2.

-Conﬁgure the network requirements on the iSmartgate-01W. See section 3.

-Conﬁgure the iSmartgate-01W according to the desired mode. See section 4

1. The desired name for the door. The default name is "home", but you can change it for anyone you want. Just take into account that it has to be no more than 8 characters, in lowercase.

2. The desired password. The default password is "12345678". You can change it, just take into account that it has to be 8 numeric characters.

3. The IP Broadcast of our network. The default one is "192.168.1.255"

4. The network port. The default one is 8001.

5. The mode you want the device to work, The default setting is "Garage"

Lastly, open the iSmargate app on your smartphone, and follow MY GATES > ADD GATE . You will be asked for

the follwing data, just be sure to complete all these ﬁelds with the same data entered in the iSmartgate Device:

1. Gate Name

2. Port

3. Password

4. Mode

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

NOTE

The iSmartgate-01W IS NOT AN AccessPoint (AP). It works as a CLIENT device (AP Client).

Therefore, it requires an AP network device (AP Wi-FI, Router Wi-Fi).

The iSmartgate-01W works as a plug-in for any garage door. It comes with 2 relay outputs that can be controlled with any iOS / Android smartphone.

These 2 outputs need to be connected to the existing garage door's control panel.

In order to allow the iSmartgate-01W get connected to the smartphone, you will need either an Access Point Wi-ﬁ (AP)

or a router Wi-ﬁ. The iSmartgate-01W will connect through Wi-ﬁ to the router/AP, and so will do the smartphone, once

it has the iSmartgate App installed. This, our smartphone and the iSmartgate device will be able to get connected eachother.

Before proceeding with the installation, please read safety instrucions in section 1.2

In order to allow the iSmartgate App get connected to iSmartgate-01W, you need to complete the following steps:

Next, you need to put the next data, using the buttons and the display on the device:

It's Not necessary to put here the IP broadcast

1.2 Safety Instructions

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

The electrical installation of the iSmartgate-01W should be done by a professional. Please read carefully all these instrucions before installing and starting to use iSmartgate.

Please follow all the instructions in detail in order to avoid personal injuries or damage to third party devices.

The iSmartgate-01W is not adequate for really sensible installations or to control very precise processes, as either a WI-FI / Ethernet network failure or a power failure can not guarante a secure control.

The iSmartgate-01W must not be used in any place where it can be in touch with explosive material or medical applications.

ATTENTION

The smartphone needs to be connected via WI-FI to the same network where the iSmartgate-01W is.

(See section 6. iSmartgate App conﬁguration).

Once the network device is conﬁgured with this two steps:

· connected to the gate

· our telephone connected to Wi-Fi to the same LAN as the router (with the parameters conﬁgured properly)

By opening the application on your smartphone you’ll can open or close the door garage.

All settings can be made in a very simple way without speciﬁc knowledge of any programming language or PC.

NOTE

VIRTUAL TO FACTUAL ELECTRONICS, S.L. will never be responsible for any possible injury or damage to people or objects that may occur due to an incorrect use or by not following these instructions. Additionally, VIRTUAL TO FACTUAL ELECTRONICS S.L. will not accept any responsibility for third party apps using it, or for any use of the iSmartgate-01W or its application, which is not speciﬁed

in this manual.

ATTENTION

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

1.3 Examples of use of the application

1. Garage Door Control (Open / Close)

2. Blinds Control (Open / Close)

3. Lighting Control, Irrigation Systems Contol ( ON / OFF)

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

2. Wiring the iSmartGate-01W

2.1 Wiring supply power

The electrical installation of the iSmartgate-01W should be done by a professional. Please follow all the instructions in detail in order to avoid personal injuries or damage to third party devices.

ATTENTION

P. E

Connect the wiring supply as it is shown in the following scheme.

Figure 2. Wiring supply Scheme

A maximum 240 Vac must never be surpassed. This device is ready to use both with 110 Vac and 220 Vac.

Installation and Disconnection must be done without power supply in order to avoid possible accidents. All regulations and rules must be taken into consideration when installing the iSmartgate-01W device. The electrical installation of the iSmartgate-01W should be done by a professional.

ATTENTION

iSmartGate-01W

LED STATUS

LED OUTPUT 1

LED OUTPUT 2

110/220AC

SEL BACK OK

RELAY 1 RELAY 2

Wi-Fi

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

2.2 Wiring Load

ATTENTION

Before to connect the load to the device outputs, check ﬁgure 6 for the maximum current

and voltage supported by iSmartGate-01W (http://www.v2fe.com/how-it-works1.html).

ATTENTION

2.2.1 iSmartGate GARAGE Mode Wiring

The iSmartGate-01W has 2 voltage free outputs: RELAY 1 and RELAY2 , to connect with electric or electronic

devices. If you want to control your Garage Door, you need to conﬁgure the iSmartgate-01W with the GRG Mode (Garage mode). If in our iSmartGate APP we have set up the door with GRG MODE, we have to connect the device

as the following scheme:

You can also choose to connect the iSmartgate-01W to the Garage Internal Wall Switch, as in the following scheme:

Figure 3. Connection of the iSmartgate-01W to a standard Garage Door Control Panel

27262524232221201918171615

121110

765

321

M1 M2

GND

POWER SUPPLY

CCURTESY

LIGHT

FLASHING LIGHT

Max 40w

MOTOR 2 CLOSE

MOTOR 2 COMMON

MOTOR 2 OPEN

MOTOR 1 CLOSE

MOTOR 1 COMMON

MOTOR 1 OPEN

OPEN

P.P.

PHOTO1

PHOTO

STOP

SCA

COM

PHOTOTEST

24 V

200mA

ELECTRIC LOCK

12 Voc MAX 25 W

LED STATUS

LED OUTPUT 1

LED OUTPUT 2

P.E N L

110/220AC

SEL BACK OK

RELAY 1 RELAY 2

Wi-Fi

Actual Wiring

NEW Wiring

OPEN button Inside

CLOSE button Inside

Actual Wiring

NEW Wiring

LED STATUS

LED OUTPUT 1

LED OUTPUT 2

P.E N L

110/220AC

SEL BACK OK

RELAY 1 RELAY 2

Wi-Fi

Figure 4a. Connect iSmartGate to your internal garage wall switch.

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

Once the iSmartgate App is conﬁgured and is able to connect to the

iSmartgate-01W (see sections 3,4, 6), we are ready to tap on the app's

OPEN button. Automatically, RELAY1 on the iSmartphone Device will be activated for 5 seconds, sending the instruction to open the door to the Garage Door Control Panel. On the other hand, as soon as we tap on the CLOSE button on our iSmartgate App on the smartphone, RELAY2 will be activated for 5 seconds, sending the instruction to close the door to the Garage Door Control Panel.

Function "GRG" or Garage is the default mode and the more suitable to open the Garage Door using the iSmartgate App. However, there are other modes available on the iSmartgate-01W that can be used with the app. (See sections 2.2.2 and 2.2.3)

Figure 5. As soon as the iSmartgate App is connected, you will be able to read: "Connected" and the circle line will appear in green.

Figure 4b. Steps to connect iSmartGate to your garage remote controller

You can also choose to connect the iSmartgate-01W to the Garage Remote Controller, following this 3 steps:

1 2

OPEN

iSmartGate-01W

Garage door

opener controller

iSmartGate-01W

Garage door opener controller

Open the Garage door

opener controller

OPEN

LED STATUS

LED OUTPUT 1

LED OUTPUT 2

P.E N L

110/220AC

SEL BACK OK

RELAY 1 RELAY 2

Wi-Fi

LED STATUS

LED OUTPUT 1

LED OUTPUT 2

P.E N L

110/220AC

SEL BACK OK

RELAY 1 RELAY 2

Wi-Fi

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

2.2.2 iSmartGate PULSE Mode Wiring

As iSmartgate-01W has two free potential outputs, it allows to control opening and close of the following elements:

· Awnings · Blinds ·Curtains

In case the AC current of the motor we need to control is equal or below the data shown on ﬁgure 6, you need to install the iSmartgate-01W as follows:

In order to do so, it is important to take into account which is the maximum ELECTRIC CURRENT at witch work the electric motor you want to control, which should never surpass the values shown on ﬁgure 6.

In most cases, the existing control devices for those elements already come with a relay incorporated on it, so that we will not have to worry about the maximum elecrtic current.

In case the electric motor of the device we want to control has higher DC current, you will need to add an INDUSTRIAL CONTACTOR between the iSmartGate-01W and the electric motor.

Figure 6. DC Current / DC Voltage for each

of the RELAY outputs

Figure 7. Wiring to control awnings, blinds, etc.

iSmartGate-01W

The electric element connected to the iSmartgate Device needs to have its own limit switch in order to stop the action on a safe way at any time, one at the upper limit and other in the lower end of the process.

ATTENTION

LED STATUS

LED OUTPUT 1

LED OUTPUT 2

P.E N L

110/220AC

SEL BACK OK

RELAY 1 RELAY 2

Wi-Fi

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

Once you have your smartphone connected to the iSmartGate-01W and conﬁgured with the PUL (Pulse) MODE, you will be able to raise or lower the blinds, awnings or curtains as explained below:

· As far as you tap OPEN and keep it pressed, the element (blind/awning, curtain) will keep lifting up, as RELAY 1 (open) will be activated. As soon as you stop tapping the OPEN button, the OPEN action will be stopped.

· When pressing CLOSE, the opposite happens: the element (awning, blind, curtain) will start going down, as RELAY 2 (CLOSE) will be activated. As soon as you stop tapping the CLOSE button , the action will stop.

2.2.3 iSmartGate ON/OFF Mode Wiring

Last, let's see how the iSmartgate-01W can also be conﬁgured as a ON/OFF mode (O/O).

Using this mode, you will be able to control the on and off of domestic elements such as lighting elements, electric appliances, etc..

ON/OFF Mode allows the iSmartGate-01W to switch indepently 2 different LOADS (on and off).

· When you tap OPEN on the iSmartgate App on your smartphone, the LOAD connected to Output1 will go ON. When tapping OPEN again, the LOAD connected to Output1 will go OFF.

· When you tap CLOSE on the iSmartgate App on your smartphone, the LOAD connected to Output2 will go ON. When tapping CLOSE again, the LOAD connected to Output2 will go OFF.

You need to install it as the Figure 8 shown below:

Figure 8. Load control in MODE ON/OFF

LOAD 1 LOAD 2

iSmartGate-01W

LED STATUS

LED OUTPUT 1

LED OUTPUT 2

P.E N L

110/220AC

SEL BACK OK

RELAY 1 RELAY 2

Wi-Fi

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

Do not exceed the RELE'S output maximum DC current. See graphic on Figure 6.

ATTENTION

3.Network

The iSmartgate-01W is a netwok device which needs to connect to the home's WLAN where it is going to be used. This WLAN needs to provide a Wi-Fi device protected with password. Usually, the standard router used for domestic

Internet connections is already Wi-ﬁ, and is the one you can easily conﬁgure to connect your smartphone to the iSmartgate-01W (Connection to Internet is not necessary).

Never use iSmartgate to control safety or electromedical equipment from whom a life of an individual or an animal can be depending on.

ATTENTION

Figure 9. Network connection scheme

INTERNET

Wi-Fi

110/220AC

DISPLAY 1X8

P1 P2 P3

OUT OPEN OUT CLOSE

The iSmartgate-01W IS NOT AN AccessPoint (AP). It works as a CLIENT device (AP Client). Therefore, it requires an AP network device (AP Wi-FI, Router Wi-Fi) and a Windows PC to set up.

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

LED INDICATORS

YELLOW

· Constant light: iSmartgate-01W is connected to an Access Point

· Flashing light: iSmartgate-01W is searching available Wi-ﬁ connections to connect.

GREEN: Network activity

Link status / Integrity

Network activity / Diagnostic

iSmartgate Network conﬁguration instructions:

3.1 Step 1: Connecting your iSmartgate-01W to the Wi-ﬁ router or AP

Do not switch on your iSmartgate device yet.

As your iSmartgate-01W is an AP client, it has no instructions on which Wi-ﬁ AP is the one it should connect, so it will connect to the ﬁrst AP non WEP/WPA password protected Wi-ﬁ available.

Therefore, we need to conﬁgure our Wi-ﬁ AP or Wi-Fi router disabling the password, so that the AP remains open.

Please take into account that you have to look on your smartphone if there are other open AP Wi-ﬁ (not password protected), as the iSmartphone-01W can connect to them.

If this is your case, you also need to change your router's or Wi-ﬁ AP SSID, naming it "Connect". This way, as the iSmartgate-01W ﬁnds more than one open Wi-ﬁ network connection, will choose the one which name's starting

with "Connect".

Once we have set up all these points, we are ready to switch on the iSmartgate-01W, and the yellow led

should be standing on, while the green led should be ﬂashing.

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

Figure 10. Seaching the iSmartgate

3.2. Step 2: Find the iSmartgate-01W on your LAN network

Once the iSmartgate-01W is connected to the AP or WI-ﬁ router and switched on, we will use a computer connected to the same network in order to ﬁnd it and therefore conﬁgure the iSmartgate device.

You have to connect through the ethernet, your PC to the AP or Wi-ﬁ router.

In order to access to the iSmartgate-01W internal conﬁguration, you will need to use Digi Device Discovery (if you don't have it, you can download it at www.v2fe.com).

Then you need to run the program, by clicking "dgdiscvr.exe" (Digi Device Discovery is owned by Digi Inc.)

In case the iSmartgate-01W device does not appear on the screen, please wait for 5 minutes and if it still is not showing up on the screen, click on "Refresh View". If you have repeatedly searched the iSmartgate-01W with no success, it may be connected to another open network, not ours, this means that you need to go back to step 1 and start the process again.

If you have found the iSmartgate-01W, please move on to step 3.3.

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

3.3. Step 3: iSmartgate-01W network options conﬁguration

Once we have found the iSmartgate-01W using Digi Device Discovery Software, you have to click on "Open Web Interface".

You have to ﬁll the following ﬁelds to enter:

Once introduced, you will get access to the Web Conﬁgurator.

On this step, you will conﬁgure the iSmartgate-01W so that it connects to the AP or Wi-ﬁ router your desired SSID and password. At this point, your AP or wi-ﬁ router is not 100% conﬁgured as you have temporally disabled its

password and it is possible that you have also needed to change its SSID. Therefore, now it's the moment to set up the iSmartgate-01W with the desired parameters, so that later it will connect to your network with those same parameters.

Haremos click en network y en WiFi LAN settings:

· Network Name; Please write here the name you want for your Wi-ﬁ network, as you will later need to give the same input data to your AP or Wi-ﬁ router.

· Connected to Access Point: You need to select this option so that the iSmartgate-01W only connects to AP or routers.

Lastly, if desired, you can conﬁgure channel and country.

Click "Apply" (not event Reset device).

3.3.1 SSID Conﬁguration

3.3.2. Conﬁguración de las WiFi security Settings

Click on "network" and then click on "WIFI Security Settings".

V2FE recommend to use the WPA encryption, conﬁguring the computer iSmartGate-01Was follows:

Last, set up the WPA password. Then we´ll have to insert it to the Access Point o Router.

Click on “Apply”.

iSmartGate-01W device will show a message to tell us that it took one minute to calculate encryption.

Once the minute ends, reset the device (Administration -> reboot).

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

If the AP or Wi-ﬁ router has been successfully conﬁgurated, the iSmargate-01W should be connected to it. To verify it, you need to run the dgdiscvr.exe and, if this software is able to ﬁnd the iSmartGate-01W,

the network conﬁguration has been successfully completed.

In any other case, go back to step 3.6.

3.5. Step 5: Veriﬁcation

To avoid communication errors, you should set the parameters in WiFi AP or Router, which will connect the equipment iSmartGate-01W, as follows:

(in general way)

Wiﬁ Settings -> ADVANCE -> 54G MODE -> 802.11b Only

ATTENTION

Reference example:

Once you have conﬁgured the iSmartGate-01W with the SSID and the safety options, you need to conﬁgure the AP or Wi-ﬁ router with same data.

Please check that:

Once you have ﬁnished conﬁgurating your AP or wi-ﬁ Router, switch off, and the switch on again

your iSmartgate-01W.

Wait until the yellow LED on your iSmartgate stays illuminated (not ﬂashing) to move on to the next step.

If this doesn't happen, go back to step 3.6.

· The PC where the dgdiscvr.exe is running, is correctly connected to the

Ap or Wi-ﬁ router through an ethernet connection.

· The iSmartGate-01W is close to the AP or router, in order to avoid coverage problems.

3.4 Step 4: AP / Wi-Fi router Conﬁguration

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

If you are reading this section, it means that after trying to conﬁgure both iSmartGate-01W and AP, with our SSID and security settings, it has not been possible to connect them.

Firstly, it is really important to be sure that you have typed exactly the same SSID and password on both network

devices (AP or Wi-ﬁ router and iSmartgate Device).

At this stage, it is not possible to access the iSmartGate-01W, as it will try to connect to a network which will have incorrect SSID or password.

Therefore, you will need to RESET the iSmartGate Device to the default factory settings:

1. Press the SEL button on the iSmartgate-01W until the display shows: "6-ResNet"

2. Press OK

3. You will be asked again if you are sure to RESET the network conﬁguration. Press OK.

4. You will be asked again if you are sure to do so. Press OK.

5. Wait until the iSmartGate-01W restarts.

At this moment, the iSmartgate-01W will start again to search for an open Wi-ﬁ network to connect.

Please go back to section 3.1.

3.6. Troubleshooting Guide

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

4. How it works

In order to conﬁgure the iSmartgate-01W parameters, you have to use the three buttons and use them according to the information appearing on the display.

· BUTTON 1: SEL

Selection Function: It will help you navigate through the different available options.

· BUTTON 2: CANCEL/BACK/MODIFY

This button will allow you to go back to the main menu or the previous selected option. When we are typing data, this button rotate the alphanumeric value.

· BUTTON 3: OK

Conﬁrmation button. Once you press it, you will either enter in the selected option, or accept the selected parameters.

4.1. GateName, Password, Port, Ipcast, and working Mode conﬁguration

In order to control the iSmartgate-01W with our smartphone, it is important to ensure a secure connection between them, avoiding third party equipments the access to it. To provide this safety connection, the iSmartgate-01W needs to have the following parametres completed successfully;

· GateName: The door's name

· Password: Numeric password to access the door control

· Port: Network Port using the TCP/IP communication.

· Working Mode: "Garage", "Pulse", or "On/Off".

Those 4 parameters, all together, will create a unique code that will be used to encript all the communications.

This is why those 4 parameters need to be introduced exactly the same way on the iSmartgate-01W and our smartphone.

Aditionally, you will also have to conﬁgure your network's IP broadcast to ensure that the device can transmit

correctly. (See section 4.6)

Once the iSmartgate is switch on, the display screen will inform you about all the selected conﬁgurations.

Reminder:

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

4.2 GateName conﬁguration

This parameter will allow you conﬁgure the door's name, with the same data on your iSmargate App on your

smartphone. The default door's name is "home". if you want to change it,please follow this steps:

1. Press the SEL button until the display screen shows the following info: "2-SET GN"

2. Press OK

3. The display message will ask you if you are sure you want to change your door's name. Press OK.

4. As you press OK, the existing door's name will appear on the display. You will have to change the

door's name one character at a time. The character ﬂashing is the one you are changing. To do that,

simply push the CANCEL button (button #2). To move on to the next character, press SEL button (button #1).

5. 5.Once you have the desired door's name, press the OK button (button #3).

6. If everything worked well, you will read "SAVED!" on the display.

4.3 Password Conﬁguration

This parameter helps you conﬁgure your door's password. The password entered in the iSmartgate-01W will have

to be the same than the one on your iSmartgate App.

The default door's password is "12345678". This ﬁeld only accepts numeric characters. In order to change the default password, which is strongly recommended, please follow this steps:

1. Press button 1 until the tet "1-SET PW" appears on the display.

2. Press OK (button 3).

3. The display message will ask you if you are sure you want to change your door's password. Press OK.

4. As you press OK, the existing password will appear on the display. The numeric character which is ﬂashing

is the one you are about to change. To do so, press button #2. To move on to the following character,

press button SEL (button #1).

5. As soon as you have the door's desired password, press the OK button (button #3).

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

4.4. Function Mode Conﬁguration

This is a very important parameter as it will decide the way the iSmartgate-01W works.

As with the previous conﬁgurations, the selected mode will be the same running on your iSmartgate App on your

smartphone. The default mode for this parameter is “Garage”.

If you want to change it, just follow these steps:

1. Press the button #1 until it shows the following message: "3-TYPE"

2. Press OK (button #3)

3. The display message will ask you if you are sure you want to change the function mode. Press OK.

4. As you press the button #1, you will be able to navigate through all the existing modes.

5. As soon as you see on the display the desired Function mode, press the OK button (button #3).

4.5. Port Conﬁguration

This is the network parameter which deﬁnes the port in which the communication will be realized. You don't

need to modify it, unless you have more than one iSmartgate device in the same LAN/WLAN network. If this is the case, you will need to select a different port for each of them, bearing in mind that them have to be comprended between port 8000 and 65535.

The default port conﬁguration is “8001”.

If you want to change it, just follow these steps:

1. Press the button #1 until it shows the following message: "3-PORT"

2. Press OK (button #3)

3. The display message will ask you if you are sure you want to change the door's network port.

Press OK (button #3).

4. As you press OK, the current enabled network port will show up on the display. The numeric character which

is ﬂashing is the one you are about to change, to do that press button #2. Once it is correct, you can move on to the next character pressing the SEL button (button #1).

5. Once you have the desired port selected, press OK (button #3).

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

4.6. IP Broadcast conﬁguration

Network parameter. The iSmartgate-01W uses Broadcast frames.

As each network can have a different private IP, you will need to conﬁgure your IP broadcast depending on your

network settings.

In order to ﬁnd your network IP broadcast, you need to follow these steps:

On a windows PC:

1. Go to Menu > Commands or Execute and type "CMD"

2. Once the new screen opens, type "ipconﬁg"

Search for the following data: IP and MASK which consists of four numbers, separated by 3 points.

In order to know your IP Broadcast, take as reference point your IP Address. Look on your mask for any zero

number. Then, subsitute the value contained on that same position on the IP address for 255.

Example:

IP 192 . 168 . 1 . 130

MASK 255 . 255 . 255 . 0

IP Broadcast 192 . 168 . 1 . 255

Figure 12. Web interface Conﬁguration.

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

The default iSmartgate-01W's IP broadcast address is “192.168.1.255”.

If you need to change it, please follow these steps:

1. Press #1 until the display shows the following text: "5- IPcast"

2. Press OK (button #3)

3. The display message will ask you if you are sure you want to change the door's network port.

Press OK (button #3).

4. As you press OK, the existing IP broadcast number will appear on the display. You will have to change the

IP broadcast number one character at a time. The character ﬂashing is the one you can change, pushing the CANCEL button (button #2). To move on to the next character, press SEL button (button #1).

5. As soon has you have the ﬁrst number deﬁned, press OK (button #3).

6. Now, the second number of the IP broadcast will appear on the display. Follow the same action than in step 4.

7. As soon as you have the second number deﬁned, press OK (button #3).

8. Now, the third number of the IP broadcast will appear on the display.

Follow the same action you have done in steps 4 and 6.

9. As soon has you have the third number deﬁned, press OK (button #3).

10. Now, the fourth number of the IP broadcast will appear on the display. Repeat the same process

you have done to change the other numbers.

11. As soon has you have the fourth number deﬁned, press OK (button #3).

NOTE

The default conﬁguration of the iSmartgate-01W is the following:

· GATE NAME: "home" (lowercase)

· PASSWORD: "12345678"

· PORT: "8001"

· Ipbroadcast: "192.168.1.255"

· MODE: "Garage"

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

4.7. Network Factory Default

· Current selected network's port

· Current Gate's Name

· Current Gate's password

· Current selected Mode

· Current selected IP broadcast

How to use the Restore Network function:

1. Press button #1 untile the display shows the option: "6-ResNet"

2. Press OK (button #3)

3. Now the display will show a message asking if you are sure to RESET the network.

Press OK (button #3).

4. You will be asked to conﬁrm again. Press OK (button #3).

5. Wait two minutes to complete the process.

If you are not able to ﬁnd the iSmartgate-01W using the Digi Device Discovery software, it is very probable that you have a different static IP adress on your network. If this is your case, you will need to reset your device, by using the function "Restore Network".

"Restore Network" function allows the iSmartgate-01W activate the internal DHCP, and therefore being able to

restore the default conﬁguration.

Restore Network DOES NOT MODIFY or DELETE:

5. Firmware Upgrade

Virtual to Factual Electronics, on its continuous effort to provide better functionalities to its products, may be frequently publishing software upgrades, that can be updated in your iSmartgate-01W.

In order to upload a new ﬁrmware to your iSmartgate-01W, you will need to download the iSmartGateLoader PC software, available for Windows, from http://www.v2fe.com/downloads.html

Once you run this software, the following window will show up:

Requisitos:

El PC donde se ejecute el iSmartGateLoader tiene que estar en la misma red que el equipo iSmartGate-01

As the window shows up, follow these steps:

1. Click on the "Browse" button and search the ﬁrmware in the computer. The ﬁrmware you need to load is ".ISG" , and you can ﬁnd it at http://www.v2fe.com/downloads.html

2. Write on the Port Number ﬁeld, the Port Number currently being used by your iSmartgate-01W

that you want to upgrade.

3. Write on the Gate Name ﬁeld, the Gate Name currently being used on the iSmartgate-01W that you want to upgrade.

4. Write on the Password ﬁeld, the password being currently used on your iSmartgate-01W that you want to upgrade.

5. After completing the previous steps, you will already have set up the iSmartgateLoader on your PC in order to load the upgrade, but before doing so, you need to inform the device, that it is going to be upgraded.

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

Figure 13. iSmartgateLoader

Requirements: The PC where you are running the iSmartGateLoader software needs to be connected to the same network where the iSmartgate-01W is, through the AP or Wi-ﬁ router.

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

Settings of the iSmartgate-01W in order to get the new ﬁrmware from the iSmartGateLoader:

1. Press both CANCEL and OK buttons, at the same time, for 10 seconds.

2. The text "UploadFW" will appear on the display. Press OK to continue.

3. The text "PressWri" will appear no on the display. Please wait for at least 3 seconds.

Then the display screen will turn off and on again.

4. At this moment, you are ready to click the "Write Flash" button on the iSmartgateLoader software, and the upgrading process will start.

Figure 14. iSmartGateLoader writting ﬂash

Before the ﬁrmware’s update, we recommend the user to take note or record the GATENAME,

PASSWORD and PORT that appear in the unit’s display. If these settings are wrong, the device will be locked for security. Make sure that the device is correctly connected to your network by checking the connection between iSmartgate APP and iSmartGate Device.

At this moment, it is really important not to switch off neither the iSmartgate-01W nor the network

cable not the router.

If, for some reason, the upgrading process cannot be completed, your iSmargate-01W will not start,

or, if it does, the display will remain with no data on it, or completely frozen.

If that is the case, please push the CANCEL button. Afterwards the unit’s display will turn off and on again. Please continue from step 4.

The iSmartGate-01W will load its previous conﬁguration.

ATTENTION

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

6. iSmartgate App Conﬁguration

The iSmartgate-01W is able to control your Garage door's, when you are using it together with the iSmartgate App, available both for iOS (iPhone) or Android operating system.

You can download this app from:

iSmartgate App main page:

· Appstore, if you are using an Apple product (http://itunes.apple.com)

· Google Play, if you are using a smartphone with Android operating system (https://play.google.com/store)

Figure 15. iSmartgate Main page.

NOTE: The following explanation will consider as "door" , that

door in which the iSmartgate-01W is already conﬁgured.

Once you download the iSmartgate app and open it, you will see on the main page a text saying: “Searching for:" This text will tell you which door is the App searching to control.

The red circle will appear as long as there is no connection between the iSmartgate App and the iSmartgate-01W.

The main reasons why there might be no connection between them are:

· Your smartphone and your iSmartgate-01W are not connected to the

same wi-ﬁ network.

· Some of the following ﬁelds: Password, GateName, or Mode do not

match with the ones introduced on the iSmartgate-01W

MY GATES button

If you press MY GATES, you will access to a speciﬁc page where you can manage all different doors where you

have an iSmartgate-01W installed. You can add new gates, delete those ones you don't want to manage with your iSmartgate App, and select the one you want to control on the Main Page.

OPTIONS button

If you press OPTIONS, you will access to a speciﬁc page where you can manage some options such as "Shake to

Open" or "Automatic Open", but take into account that these options are only available if you have your iSmartgate-01W on mode GARAGE.

FAQS button

If you press FAQ's button, you will access to our FAQ's section, aimed to solve the most common doubts you may have while using iSmartgate.

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

6.1. Adding a New Door to the iSmartgate App

The ﬁrst time you enter into this section, there will be no gate predeﬁned, so you need

to tap "ADD GATE".

Figure 16. MY GATES Menu

Figure 17. ADD GATE Menu

As you tap "ADD GATE", you will see a new page, where you can set up a new gate. These are the

ﬁelds you need to ﬁll in:

· GATE NAME: Please write here the same GateName introduced on the iSmartgate-01W

(see section 4.2.).

ATTENTION: Always write lowercase, and take into

account that this ﬁeld is also space sensitive.

· PASSWORD: Introduce here the same password

conﬁgured on the iSmartgate-01W

· TYPE: Choose the same type you have selected on your iSmartgate-01W (section 4.4).

Once all these ﬁelds are set up, tap “SAVE GATE”. After doing so, this door will appear on the GATES

LIST Menu.

Figure 18. New door added to My Gates.

Once you have created a new door, select it by tapping on it. A check icon will appear next to the Gate's name.

You will also have information about the

mode conﬁgured for each door (below the Gate Name) , and the network port it is using

to connect. The password will not appear, for safety reasons.

Figure 19. Connection OK

Once everything is set up, you can go back to the main manu by tapping “BACK”. If the iSmartgate-01W is already connected and

correctly conﬁgured, a message will appear on the main page: CONNECTED.

You already have your iSmartgate-01W

and your iSmargate App correctly

conﬁgured and ready to use.

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

6.2 App Options

The iSmartgate App has an additional section on its main menu, called OPTIONS. If you tap on its button, we will

be redirected to a page, where you will ﬁnd 2 different options:

These 2 options are only available when you have your iSmartGate device conﬁgured on the GARAGE MODE. If you use ON/OFF or PULSE MODES, these options will not work.

ATTENTION

· Shake to Open

If you activate this function, you will be able to open or close the door by shaking your iPhone, as long as:

· You have conﬁgured you garage door with the Garage Mode

· You are connected (see ﬁgure 19).

· You are on the main page (see ﬁgure 19).

· Automatic Open

If you activate this function, your garage door will open as soon as you open the iSmartgate App on your smartphone. This way, you won't need to tap two times in order to get your garage door open (one time to activate the

app, and a second time to tap OPEN).

By only activating the iSmartgate App, your garage door will open, as long as:

· Your iSmartgate App is not running in the background.

· You are connected (see ﬁgure 19).

INSTALLATION MANUAL · iSmartGate 01W · English / REV.3

iSmartGate-01W

www.v2fe.com

iSmarGate 01W Instructions For Use Manual

Specifications and Main Features

Frequently Asked Questions

User Manual