Page 1
V3-L
RGB/CCT/Dimming 3 Channel LED RF Controller
● Match with RF 2.4G single zone or multiple zone single color,
dual color and RGB/RGBW remote control.
● One RF controller accept up to 10 remote control.
● 4096 levels 0-100% dimming smoothly without any flash.
● , built in 10 dynamic mode, When using with RGB light
include jump or gradual change style.
● Auto-transmitting function: Controller automatically transmit signal
to another controller with 30m control distance.
● Synchronize on multiple number of controllers.
● Light on/off fade time 3s selectable.
● Connect with external push key to achieve on/off and 0-100% dimming function.
● Over-heat / - / , Over load Short circuit protection recover automatically.
Technical Parameters
RF RGB/CCT/DIM
LVD RED
Input and Output
Input voltage
Input current
Output voltage
Output current
Output power
Output type
12-48VDC
18.5A
3x(12-48)VDC
3CH,6A/CH
3x(72-288 )W
Constant voltage
Warranty
5 years Warranty
Protectio n
Reverse pol ar it y,Over-h ea t
Over-load ,S ho rt c ir cuit
Mechanical Structures and Installations
Push switch 3
Push switch 2
Push switch 1
Push switch common
Match key
LED indicator
Push-D im
GND
MATCH
Dimming data
Input signal
Control distance
Dimming gray scale
Dimming range
Dimming curve
PWM frequency
Package
Size
Gross weight
+
B
G
OUTPUT
R
1 2 3
WW NW NC
-
+
IN PUT
12-48V DC
RF 2.4GHz + Push Dim
30m(Barrier-free space)
4096 (2^12) levels
0 -100%
Logarithmic
1000Hz (default)
L178x W50 x H38mm
0.130kg
Output LED +
Output Blue LED -
Output Green LED -
Output Red LED -
Installation rack
Power Input -
Power Input +
Safety and EMC
EMC standard (EMC)
Safety standard(LVD)
Radio Equipment(RED)
Certication
Environment
Operation temperature
Case temperature (Max.)
IP rating
45mm
ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
EN 62368-1:2020+A11:2020
ETSI EN 300 328 V2.2.2
CE,EMC,LVD,RED
Ta: -30OC ~ +55OC
O
+85
Tc:
C
IP20
175mm
160mm
27mm
Match Remote Control (two match ways)
End us er can choo se the suit able matc h/delete ways. Two opti ons are offered for selection:
Use the controller’s Match key
Match:
Short press match key, immediately press on/off key (single zone remote)
or zone key (multiple zone remote) of the remote.
The LED indicator fast flash a few times
means match is successful.
Delete:
Press and hold match key for 5s to delete all match,
The LED indicator fast flash a few times
means all matched remotes were deleted.
User Manual Ver 1.1.1
2023. 10
Use Power Restart
Match:
Switch off the power of the receiver, then switch on power, repeat again.
Immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power of the receiver, then switch on power, repeat again.
Immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
Page 1
Page 2
Wiring Diagram
● V3-L for RGB
RGB remote
● V3-L for dual color
+
Push-Di m
GND
MATCH
V3-L
B
G
OUTP UT
R
1 2 3
WW N W NC
-
+
IN PUT
12-48V DC
RGB LED strip
AC100-240V
Power Supply
12-48VDC
Constant Voltage
GND
MATCH
CCT remote
● V3-L for single color
GND
MATCH
Dimming remote
● V3-L with three push key for 3 channel single color
Push Key x 3
GND
MATCH
+
Push-Di m
V3-L
B
G
OUTP UT
R
1 2 3
WW N W NC
-
+
IN PUT
12-48V DC
CW
WW
Dual color LED strip
+
Power Supply
AC100-240V
12-48VDC
Constant Voltage
+
Push-Di m
V3-L
B
G
OUTP UT
R
1 2 3
WW N W NC
-
+
IN PUT
12-48V DC
Single color LED strip
+
Single color LED strip
+
Single color LED strip
+
AC100-240V
Power Supply
12-48VDC
Constant Voltage
+
Push-Di m
V3-L
B
G
OUTP UT
R
1 2 3
WW N W NC
-
+
IN PUT
12-48V DC
Single color LED strip
+
Single color LED strip
+
Single color LED strip
+
AC100-240V
Power Supply
12-48VDC
Constant Voltage
Wire Preparation:
1. The wiring can be solid or stranded with a cross-sectional area of 0.5 to 2 mm².
0.5-2.0mm
Conventional 1mm² can withstand 10A output current.
2. When wiring is installed, the terminals must be tightened.
If they are not tightened, the contact point resistance will be too high and the terminals will
4-5mm
easily burn due to heat when used at full load for a long time.
Note: The output power of a constant voltage power supply should be at least 1.2 times that of the output load (light strip),
otherwise the full power output of the load can easily cause automatic flickering or shaking of the light.
Light on/off fade time
Long press match key 5s, then short press match key 3 times,the light on/off time will be set to 3s, the indicator light blink 3 times.
Long press match key 10s, restore factory default parameter,the light on/off time also restore to 0.5s.
User Manual Ver 1.1.1
2023. 10
Page 2
Page 3
Push-Dim control
The 3 push key have 3 channel dimming function defaultly.
● Short press: Turn on or off each channel.
● Long press (1-6s): Press and hold to step-less dimming of each channel,
With every other long press, the light level goes to the opposite direction.
● Dimming memory: Light returns to the previous dimming level when switched off and on again.
You also can long press push key and Match key at the same time to select 3 kinds light type,
and each light type will have different push key function.
Long press 1 key and Match key 2 seconds, set as 3 channel single color type (default).
Long press 2 key and Match key 2 seconds, set as dual color type.
Long press 3 key and Match key 2 seconds, set as RGB type.
at this time, if the light type has set as dual color or RGB, match remote will not change light type.
If you want to cancel light type set, please long press Match key 10 seconds to restore factory setting.
Short press turn on/off 1 channel, long press 1-6s dim up/down
Single color
(3 CH)
Dual color
RGB
1 key
2 key
Short press turn on/off 2 channel, long press 1-6s dim up/down
3 key
Short press turn on/off 3 channel, long press 1-6s dim up/down
1 key
Short press turn on/off light, long press 1-6s dim up/down
Short press 3 levels color temperature (WW, NW, CW), long press 1-6s color temperature up/down
2 key
3 key
Unvalid
1 key
Short press turn on/off light, long press 1-6s dim up/down
Short press change dynamic mode, long press 2s to set speed (1-10 levels)
2 key
Short press change static RGB color (24 levels), long press 1-6s adjust saturation
3 key
RGB dynamic mode list
No. Name
1
2
3
4
5
RGB jump
RGB smooth
6 color jump
6 color smooth
Yellow cyan purple smooth
Malfunctions analysis & troubleshooting
Malfunctions
No light
Wrong color
Uneven intensity
between front and
rear,with voltage drop
No response
from the remote
1. No power.
2. Wrong connection or insecure.
1. Wrong connection of R/G/B wires.
1. Output cable is too long.
2. Wire diameter is too small.
3. Overload beyond power supply capability.
4. Overload beyond controller capability.
1. The battery has no power.
2. Beyond controllable distance.
3. The controller did not match the remote.
Causes
10
NameNo.
6
7
8
9
RGB fade in and out
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
Troubleshooting
1. Check the power.
2. Check the connection.
1. Reconnect R/G/B wires.
1. Reduce cable or loop supply.
2. Change wider wire.
3. Replace higher power supply.
4. Add power repeater.
1. Replace battery.
2. Reduce remote distance.
3. Re-match the remote.
InstallationPrecautions
1. The products shall not be stacked, the distance should be ≥ 20cm, so as not to affect lifespan of the products due to poor heat dissipation.
2. The product shall not be installed close to the switching power supply with an interval of ≥ 20cm to avoid radiation interference of the switching power supply.
3. The installation height shall be ≥ 1m from the oor to avoid shortening the remote control distance due to too weak reception signal.
4. The products are not allowed to be close to or covered by metal objects, with an interval of ≥ 20cm to avoid signal attenuation and shorten the remotedistance.
5. Avoid installation at the corner of the wall or the corner of the beam, with an interval of ≥ 20cm to avoid signal interference.
User Manual Ver 1.1.1
2023. 10
Page 3
Loading...