Add Bluetooth Capability to
Your Factory Radio
®
BluStream™
Owner’s
Manual
ISBT21
For use with the PXAMG
Automotive Media GateWay
iSimple Solutions®,
A division of AAMP of America™
13160 56th Court Clearwater, Florida 33760
Ph. 866-788-4237
support@isimplesolutions.com
©2009 AAMP of Florida, Inc.
Rev. 12-28-09
INST021
Table of Contents
Pages
1. Introduction 1
2. Compatibility 4
3. Installation 4
4. Pair Your iPhone 5
5. Bluetooth Functions & Controls 5
6. Warranty Information 7
ISBT21 & Optional Add-ons
Factory Radio
(not included)
Vehicle Specic Harness
(not included, actual harness
may vary)
GateWay™ Interface
(not included)
HD Radio
OR
Satellite Radio
OR
OR
iPod Input
OR
AUX Input
ISBT21
1. Introduction
Thank You for purchasing the iSimple ISBT21 add-on Bluetooth®
module for the GateWay (uPAC). This device is designed to plug into the
GateWay (uPAC) (sold separately) and provide a Bluetooth connection
for your iPhone. The ISBT21 enables you to connect your iPhone
wirelessly to your factory audio system so your phone conversation
plays through your automobile’s speakers. Operation includes features
such as: answer/reject incoming call, call waiting, privacy mode and
A2DP streaming audio.(iPhone MUST have rmware 3.0 or higher. First
generation iPhones do not support A2DP streaming audio)
2. Compatibility
To ensure proper operation please verify that your GateWay (uPAC)
is updated with the latest firmware. Please visit
www.isimplesolutions.com for firmware updates and compatibility
information.
3. Installation
The GateWay (uPAC) must be disconnected from the vehicle and
allowed to sit for no less than ve minutes before installing the
ISBT21. The vehicle wiring harness may be left in place, but MUST BE
DISCONNECTED from the GateWay (uPAC) interface before installing
the Bluetooth Module. After you have disconnected the GateWay
(uPAC) and waited at least ve minutes, connect the 8-pin to 8-pin
DIN cable into the rst port on the GateWay (uPAC) (farthest from
the dipswitches). Connect the other end of the cable into the ISBT21
module. Be sure each end makes a secure connection, but do not
force it. Decide on a mounting location for the microphone either on the
headliner or overhead console. Avoid placing the microphone by the
side windows to eliminate extra noise. Carefully run the microphone
cable down into the dash where the ISBT21 is to be installed.
When securing the ISBT21 into the dash of the vehicle, placement of
the interface is very important. Bluetooth technology supports devices
communicating wirelessly up to 20 feet away in most cases. However
metal structures inside the dash can reduce the communication
between the module and the Bluetooth device. Please keep this in mind
when installing the ISBT21 module and ensure to place it where it will
have the least obstructions from metal objects.
With all wiring connected, reconnect the GateWay (uPAC) to the vehicle
harness.
After all connections have been made, turn the ignition on in the
vehicle. Wait 1 minute for the device to initialize. Cycle ignition OFF,
and ON again. Enter Satellite radio mode to access the GateWay
(uPAC) and use the Bluetooth Module.
4
4. Pair Your Phone
To use the iPhone with the ISBT21 you must rst pair it with the
Bluetooth module. Enter your iPhone’s Bluetooth menu by going to
Settings>General>Bluetooth and search for a new device. It should
discover the ISBT21 named “PHONEKIT”. If prompted for a PIN code
enter 0000, otherwise just select “Pair”.
If your iPhone can not nd the “PHONEKIT” when you perform a
Bluetooth device search, then follow these steps to use the ISBT21 to
pair to your iPhone:
1. Enter menu (please see your vehicle specic section for menu access
& navigation)
2. Select “Settings” then select “BT Search”
3. After the search nishes, scroll through the list of devices until you see
your iPhone
4. Select your iPhone
5. If prompted for a PIN code enter 0000, otherwise just select “Pair”.
6. Your iPhone is now paired
5. Bluetooth Functions & Controls
This section will inform you of the overall features of the ISBT21.To see
vehicle specic functions please refer to your vehicle specic section.
Phone Features
1. Answer/End Call - Allows you to make, recieve & end phone calls
directly from the factory radio.
2. Call Waiting - Allows you to receive a call while on another call.
3. Privacy Mode - Allows you to transfer the audio from the vehicle
speakers to the handset. You can also answer the call from the phone
itself to make the ISBT21 instantly go into privacy mode.
4. Reject Call - Allows you to reject an incoming call.
5. Voicedial - Allows you to press a button on the radio and say the
name of the person you wish to call
6. Call History - Allows you to scroll through a list of the most recent
incoming calls to your phone.
7. Call Last # - Allows you to call the last incoming number to your
phone.
5
8. Menu - Allows you to adjust settings such as A2DP volume &
microphone volume, search for other Bluetooth devices as well as pair
and remove devices.
Menu Options
Please see your vehicle specic section for menu navigation
1. Settings - Allows you to perform a search for other Bluetooth enabled
devices, adjust the microphone volume & adjust the A2DP volume.
2. Devices - Allows you to see a list of paired devices as well as switch
between paired devices. The device which is active at the time will be
represented with an [A] next to the device name. If there is no active
device at the time there will not be an [A] present.
3. Remove - Allows you to remove paired devices
IMPORTANT NOTE
In order to access the Voicedial, Call History, Call Last # & Menu
functions, the factory radio MUST be in Bluetooth mode. Please see your
vehicle specic section for further details.
Streaming Audio Features
1. A2DP Streaming Audio - Allows you to stream audio wirelessly from
your iPhone. (iPhone MUST have rmware 3.0 or higher. First generation
iPhones do not support A2DP streaming audio)
2. Play/Pause - Allows you to play/pause A2DP audio with the touch of a
button.
IMPORTANT NOTE
When using the ISBT21 in conjunction with an iPod cable on the
GateWay (uPAC), if the iPhone is playing but you do not hear any
sound, check that the output source listed at the bottom of the
iPhone matches the source on the radio. This problem only occurs
when you have the iPhone hooked to the GateWay (uPAC) dock
connector and connected to the ISBT21 simultaneously.
6
6. Warranty Information
One Year Limited Warranty
The quality controls used in the manufacture of this product will ensure your satisfaction.
This warranty applies only to the original purchaser of this product from an authorized
ISimple Solutions dealer. This warranty covers any supplied or manufactured parts of this
product that, upon inspection by ISimple Solutions authorized personnel, is found to have
failed in normal use due to defects in material or workmanship. This warranty does not
apply to installation expenses. Attempting to service or modify this unit, operating this unit
under conditions other than the recommended voltage will render this
WARRANTY VOID.
Unless otherwise prescribed by law, ISimple Solutions shall not be liable for any
personal injury, property damage and or any incidental or consequential damages of any
kind (including water damage) resulting from malfunctions, defects, misuse, improper
installation or alteration of this product. All parts of this ISimple Solutions product are
guaranteed for a period of 1 year as follows:
Within the rst 12 months from date of purchase, subject to the conditions above, ISimple
Solutions will repair or replace the product at their discretion, if it is defective in material
or workmanship providing it is returned to an Authorized iSimple Solutions Dealer, with
PROOF OF PURCHASE from an authorized ISimple Solutions dealer.
Warning:
This equipment may be reset by unintentional electrostatic discharge during operation.
Exposure to direct sunlight or extreme heat may cause damage or malfunction.
FCC Class B Radio Frequency
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that of which the receiver is connected.
4. Consult the dealer or an experienced radio / television technical
for help.
Notice : The changes or modications not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment.
FCC ID: XBD-PXAMGBT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this devicemay not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
7
www.isimplesolutions.com
iSimple Solutions®,
a division of AAMP of America™
13160 56th Court Clearwater, Florida 33760
Ph. 866-788-4237
support@isimplesolutions.com
©2009 AAMP of Florida, Inc.
For Best Performance Have It
Professionally Installed.
8
Loading...