ITP- Series
Price Computing Scale
Scale Users Guide
ISHTAA SCALES INC., COIMBATORE, INDIA
www.ishtaascales.com
CONFIGURATION
• PRESS T/Z AND MODE & SWITCH ON THE SCALE. THE DISPLAY WILL SHOW
CONFIG.
• TO CHANGE THE CAPACITY, CHANGE THE DIGIT OF PERTICULAR
CAPACITY…
THEN SET 0 TO 30 KG (30.000) USING ACL & CL KEY.THEN PRESS SET KEY.IT
WILL SHOW RESAL ON DISPLAY.
• TO CHANGE THE RECAL USE ACL & CL KEY
• THEN PRESS T/Z KEY .IT WILL SHOW AUTO-0.
• TO CHANGE AUTO-0, YOU CAN PRESS UP TO 0 TO 9 USING KEY PAD.
• PRESS SET KEY,IT WILL SHOW DP ON DISPLAY
• TO CHANGE THE DP USE ACL & CL KEY FROM KEY PAD
• PRESS SET KEY,IT WILL SHOW DG. OFF ON DISPLAY
• TO CHANGE DG. OFF USE ACL & CL KEY FROM KEY PAD. (EITHER YES OR
NO).
• PRESS SET KEY,IT WILL SHOW LST DG ON DISPLAY
• TO CHANGE LST DIG PRESS ACL & CL KEY FROM KEY PAD (EITHER YES OR
NO).
• PRESS SET KEY,IT WILL SHOW LETER ON DISPLAY
• TO CHANGE LETER PRESS ACL & CL KEY FROM KEY PAD.
• PRESS SET KEY.IT WILL SHOW LTER-U ON DISPLAY.
• TO CHANGE LTER-U PRESS ACL & CL KEY FROM KEY PAD.
• PRESS SET KEY,IT WILL SHOW LTER-DES ON DISPLAY & ASK FOR
PASSWARD.
• TO SET THE PASSWARD USE KEY PAD TO ENTER 8756 AS DEFAULT
PASSWARD.
• PRESS SET KEY,IT WILL SHOW DENSITY ON DIPLAY.
• TO SET DENSITY,PRESS ACL & CL KEY FROM KEY PAD.THE DEFAULT
VALUE OF DENSITY IS 970.
• PRESS SET KEY,IT WILL SHOW PIECE ON DISPLAY.
• TO SET PIECE, PREE ACL & CL KEY FROM DISPLAY.
• PRESS SET KEY.IT WILL SHOW L-LMIT(LOWER LIMIT) ON DISPLAY.
• TO SET L-LMIT USE KEY PAD
• PRESS SET KEY,IT WILL SHOW H-LMIT(HIGHER LIMIT) ON DISPLAY
• TO SET H-LMIT USE KEY PAD.
• PRESS SET KEY.
NOTE: AS YOU PRESS SET KEY, IT WILL AUTO SAVE YOUR ALL CONFIG
SETTING.
FACTORY CALIBRATION
• PRESS MODE & MT THEN SWITCH ON THE SCALE, THE DISPLAY WILL
SHOW PASS.
• ENTER THE DEFAULT PASS WARD 8756 USING KEY PAD.
• PRESS SET KEY, IT WILL SHOW SEG-1 ON DISPLAY.
• TO CHANGE THE CAPACITY OF SEG-1,USE KEYPAD TO CHANGE THE
PERTICULAR DIGIT OF CAPACITY.THE DIGIT WILL START BLINKING AS YOU
REACH ON PERTICULAR DIGIT.
• THE PRESS SET KEY AFTER CHANGE THE SEG-1. IT WILL SHOW SEG-2 ON
DISPLAY.
• TO CHANGE THE CAPACITY OF SEG-2,USE KEYPAD TO CHANGE THE
PERTICULAR DIGIT OF CAPACITY.THE DIGIT WILL START BLINKING AS YOU
REACH ON PERTICULAR DIGIT.
• THEN PRESS SET KEY,IT WILL SHOW LOAD ON YOUR DISPLAY.
• FIRST PUT THE WEIGHT THAT YOU ENTER IN SEG-1 & PRESS SET.
• THEN PUT THE WEIGHT THAT YOU ENTER IN SEG-2 & PRESS SET.
FIELD CALIBRATION
• PRESS “LEFT ARROWKEY ”AND “UP ARROW KEY” & SWITCH ON THE
SCALE.THE DISPLAY WILL SHOW PASS.
• ENTER THE DEFAULT PASS WARD 8756 USING KEY PAD.
• PRESS SET KEY, IT WILL SHOW SEG-1 ON DISPLAY.
• TO CHANGE THE CAPACITY OF SEG-1,USE KEYPAD TO CHANGE THE
PARTICULAR DIGIT OF CAPACITY.THE DIGIT WILL START BLINKING AS YOU
REACH ON PERTICULAR DIGIT.
• PRESS SET, THE DIPPLAY WILL SHOW LOAD.
• PUT THE WEIGHT THAT YOU ENTER IN SEG-1 &PRESS SET KEY.
FOR MEMORY SETTING
• PRESS * KEY ,IT WILL SHOW ‘0’ ON DISPLAY.
• THEN PRESS M1,IT WILL SHOW ‘1’ ON DISPLAY.
• PRESS SET KEY & SIMENTANIOUSLY PRESS * KEY.
• IT WILL SHOW VALUE OF M1 ON DISPLAY. TO CHANGE THE VALUE OF M1,
PRESS CL KEY FROM KEYPAD & PRESS SET KEY
TO SET DIRECT VALUE
• TO SET THE DIRECT VALUE,PRESS CL KEY & ENTER THE VALUE
• PRESS SET KEY
TO INCREASE MEMORY WEIGHT
• TO INCREASE MEMORY WEIGHT PRESS MT KEY & INSTALL THE MEMORY.
• TO SEE THE TOTAL VALUE, PRESS MR KEY. & AGAIN PRESS MR KEY TO
CLOSE.
• TO CLEAR THE MEMORY PRESS ACL KEY.
• TO SEE VALUE OF 0 TO 99 MEMORY, PRESS *(STAR).
• THE DISPLAY WILL SHOW 0 blank. ENTER ANY NUMBER BETWEEN 0 TO 99 and
PRESS *,WILL SHOW YOU THE VALUE OF MEMORY.
Loading...