Page 1
User’s Manual
Ver. 1.02
IMPORTANT
• Read this manual thoroughly, and do not perform installation,
operation, maintenance, or inspection unless you fully
understand all of the contents.
• Keep this manual in a safe place where you can refer to it
easily while installing, operating, and carrying out
maintenance or inspections.
RS-61004-11 1.02
Page 2
© ISHIDA Co., Ltd. 2008 All rights are reserved.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means
mechanical, electronic, photocopying, recording, or otherwise without prior written permission of ISHIDA.
Page 3
Chapter 12 ADJUSTMENT MODE
ADJUSTMENT MODE
12.1 ADJUSTMENT MODE ENTRY
1.
Make sure that the initial screen is displayed.
2.
Press the [MODE] key on the key sheet.
The Operation Mode screen appears. Then, press the [ADJUST] button on the screen
3.
The Adjustment Menu Select screen appears.
12
UNI-5 User’s Manual 12-1
Page 4
Chapter 12 ADJUSTMENT MODE
12.2 DATE / TIME ADJUSTMENT
1.
Press the “TIME / DATE SET” field on the Adjustment Menu Select screen.
2.
The Time/Date Set screen appears.
3.
To change the date, enter a new date and press the “DATE” field.
EXAMPLE 22 June, 2007
12-2 UNI-5 User’s Manual
Page 5
Chapter 12 ADJUSTMENT MODE
4.
To change the time, enter a new time and press the “TIME” field.
EXAMPLE 13:50:00
5.
To register new date and time, press the [SET] button.
6.
The confirmation screen appears. Then, press the [EXEC] button for execution.
UNI-5 User’s Manual 12-3
Page 6
Chapter 12 ADJUSTMENT MODE
12.3 TOUCH PANEL ADJUSTMENT
1.
Press the “TOUCH PANEL” field on the Adjustment Menu Select screen.
2.
The Touch Panel screen appears.
3.
Press the [+] button on the upper left of the screen.
4.
Press the [+] button on the lower right of the screen.
12-4 UNI-5 User’s Manual
Page 7
Chapter 12 ADJUSTMENT MODE
5.
Press the [SET] button to confirm calibration.
UNI-5 User’s Manual 12-5
Page 8
Chapter 12 ADJUSTMENT MODE
12.4 DISPLAY CHECK
1.
Press the “DISPLAY CHECK” field on the Adjustment Menu Select screen.
2.
The Display Check (Vertical) screen appears.
Press the [-] or [+] button to adjust vertical brightnesses for the operator and customer
displays.
3.
Press the [HORIZONTAL] button to change to the horizontal display check screen.
4.
The Display Check (Horizontal) screen appears.
Press the [-] or [+] button to adjust vertical brightnesses for the operator and customer
displays.
12-6 UNI-5 User’s Manual
Page 9
Chapter 1 BEFORE USE
BEFORE USE
1.1 SPECIFICATIONS
Items Descriptions
Use conditions
Temperature: 5 to 35°C
Humidity: 30 to 85%, Non condensing.
Power supply: AC100 – 240V, 50 / 60Hz
Power consumption 1.0A/0.5A
Weight Bench type: Approx.11.5 kg
Pole type: Approx.12.5 kg
Weighing capacity 15 kg: 0 to 6/0.002 kg, 6 to 15/0.005 kg
Weighting accuracy 1/3000
Operator/Customer display 7.0 inch color, monochrome liquid crystal with back light, 480 X
234dots
Printing method Direct thermal method
Thermal head 2 inches (448dots) and 8 dots/mm
Printing speed 100mm/second, 120mm/second
Note: The printing speed may vary according to label conditions.
Printing effective size 56mm
Label size Label width: 30mm to 60mm
Label length: 20mm to 150mm
Number of label cassettes 7 cassettes
Input/Output LAN 1 channel
USB 1 channel
CF 1 channel
Drawer 2 channels
Program store medium Flash ROM (32M bytes)
1
UNI-5 User’s Manual 1-1
Page 10
Chapter 1 BEFORE USE
1.2 MODEL VARIATIONS
Bench Type
Pole Type
Elevated Type
Self-service Type
1-2 UNI-5 User’s Manual
Page 11
Chapter 1 BEFORE USE
1.3 PART NAMES AND FUNCTIONS
1.3.1 FRONT VIEW (BENCH TYPE)
1.3.2 REAR VIEW (BENCH TYPE)
UNI-5 User’s Manual 1-3
Page 12
Chapter 1 BEFORE USE
1.4 OPERATION PANEL
Keys for Usual Use
Used to delete an entered
numerical value.
Used to display Menu Select
screen.
Used to call a registered product
data.
Used to turn the previous page.
Used to feed labels.
Used to turn the next page.
Used to issue a label.
Used to jump to the top page.
Used to enter tare weight.
Used to jump to the end page.
Used to reset a weigh to zero.
Used to escape from the current
mode.
1-4 UNI-5 User’s Manual
Page 13
Chapter 1 BEFORE USE
1.5 ADJUSTMENTS
1.5.1 LEVEL ADJUSTMENT (BENCH TYPE)
Install the machine horizontally to use.
Be sure to turn off the power switch before placing the machine on a stable platform, and adjust the
machine inclination by turning the four level adjustment feet so that the bubble is located at the center
of the level gauge. Accurate measurements cannot be performed if it is not installed horizontally.
1.5.2 OPERATION PANEL ANGLE ADJUSTMENT (BENCH TYPE)
To obtain a better view, adjust the angle of the operation panel within the range between 0 and 70
degrees.
UNI-5 User’s Manual 1-5
Page 14
Chapter 1 BEFORE USE
1.6 LABEL / RECEIPT ROLL LOADING
1.
Open the cover on the side of main body.
2.
Set a new roll around the roll holder and raise the roll stopper to fix the roll position.
3.
Thread the paper as shown in the figures below..
1-6 UNI-5 User’s Manual
Page 15
Chapter 1 BEFORE USE
4
For labels, fix the paper end with the backing paper stopper, and gently turn the winding
bobbin counterclockwise until the label becomes tight.
5.
Slide the label/receipt guide to help smooth paper feeding according to the paper width.
UNI-5 User’s Manual 1-7
Page 16
Chapter 1 BEFORE USE
6.
For labels, press the [FEED] key on the key sheet to issue a label.
At this time, confirm that the label is completely peeled off.
Confirm that the backing paper is wound up smoothly. If the backing paper is wound up
diagonally, check that the label is set correctly.
1-8 UNI-5 User’s Manual
Page 17
Chapter 1 BEFORE USE
1.7 REMOVING & REPLACING OF WEIGH PLATTER
1.7.1 REMOVING THE WEIGH PLATTER
When removing the weigh platter from the main body, lift the front side to pull out the two pins from
the two rubber platter holders and remove the platter by pulling it to disengage the two hooks at the
rear side of the platter.
1.7.2 REPLACING THE WEIGH PLATTER
When replacing the weigh platter onto the main body, engage the two hooks at the rear side of the
platter and lower the platter so that the two pins on the bottom of the platter are inserted into holes of
the rubber platter holders.
UNI-5 User’s Manual 1-9
Page 18
Chapter 1 BEFORE USE
1.8.4 PRECAUTIONS WHEN USING CLEANING FLUIDS
Use a soft cloth and a neutral detergent to clean the machine.
Do not use thinner, benzene, etc. Doing so may damage the original safety functions.
For some parts, use cleaning fluid (isopropyl alcohol).
Do not use cleaning fluid near fire as the fluid is flammable.
Do not use cleaning fluid in a poorly ventilated area. Always provide adequate
ventilation when cleaning.
Take the following actions in the event of an accident:
If the fluid gets in your eye
Immediately wash your eye(s) with water for at least 15 minutes, and consult your
doctor.
If you wear contact lenses, remove and wash them.
If the fluid comes into contact with your skin
Immediately rinse the area of contact with water, and then wash with soap.
If you notice any skin abnormalities at the area of contact, or if any pain persists,
consult your doctor.
If the fumes of the fluid are inhaled
Immediately move the victim to an area where fresh air is available, and have the
victim lie down and keep warm.
If breathing becomes difficult or stops, provide artificial respiration and seek medical
attention immediately.
If the fluid is swallowed
Do not try to induce vomiting.
Do not give the victim anything to drink, and do not rinse the mouth.
If vomiting occurs naturally, have the victim lean forward to reduce risk of aspiration.
Keep the victim warm and seek medical attention.
1-10 UNI-5 User’s Manual
Page 19
Chapter 1 BEFORE USE
1.9 STARTING PROCEDURES
1.9.1 TURNING ON THE POWER
1.
Push down the "I” side of the Power Switch to turn on the power.
2.
The Time Check screen appears.
Then, check that displayed date and time agree with current date and time, and press the
[ENTER] button on the screen to proceed to the next step.
Note: Refer to “Time/Date Set” menu in Adjust Mode when changing the date or time.
21-JUN-2007
11:13:38
3.
After a while, the initial screen appears.
UNI-5 User’s Manual 1-11
Page 20
Chapter 1 BEFORE USE
1.9.2 PERFORMING ZERO ADJUSTMENT
1.
If the weight value is not zero on the initial screen,
Press the [ZERO] key on the key sheet to perform zero weight adjustment.
2.
The “ZERO” indicator lights up and the weight value becomes zero.
1-12 UNI-5 User’s Manual
Page 21
Chapter 1 BEFORE USE
1.9.3 GETTING BACK TO THE INITIAL SCREEN
1.
To get back to the initial screen from a Menu Select screen, press either the “SALES” field
or the icon at the bottom right on the screen.
2.
The initial screen appears.
UNI-5 User’s Manual 1-13
Page 22
Chapter 2 LABEL ISSUE
LABEL ISSUE
2.1 LABEL ISSUE WITHOUT OPERATOR
2.1.1 WEIGHING UNIT PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
When the product is preset as a traceable item, the traceability screen appears.
See Chapter 4 for more details about traceability products.
4.
The selected PLU screen appears.
Without Preset Tare Weight
2
UNI-5 User’s Manual 2-1
Page 23
Chapter 2 LABEL ISSUE
With Preset Tare Weight
Manual Tare Entry
To newly enter a tare weight or overwrite an existing tare weight, enter the tare weight
using the numeric keys and press the “TARE” field on the screen.
EXAMPLE Tare weight “50g”
5.
See Chapter 5 for more details about temporary change operations.
6.
Put a product on the weigh platter.
The weight is measured and the total price is calculated.
2-2 UNI-5 User’s Manual
Page 24
Chapter 2 LABEL ISSUE
7.
When “MANUAL” is set in the Print Mode,
Press the [PRINT] key on the key sheet.
The label is issued.
Non-traceable products Traceable products
When “AUTO” is set in the Print Mode,
The label is automatically issued as soon as the weighing is stabilized.
Non-traceable products Traceable products
UNI-5 User’s Manual 2-3
Page 25
Chapter 2 LABEL ISSUE
2.1.2 WEIGHING FIXED PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
When the product is preset as a traceable item, the traceability screen appears.
See Chapter 4 for more details about traceability products.
4.
The selected PLU screen appears.
Without Preset Tare Weight
2-4 UNI-5 User’s Manual
Page 26
Chapter 2 LABEL ISSUE
With Preset Tare Weight
Manual Tare Entry
To newly enter a tare weight or overwrite an existing tare weight, enter the tare weight
using the numeric keys and press the “TARE” field on the screen.
EXAMPLE Tare weight “50g”
5.
See Chapter 5 for more details about temporary change operations.
6.
Put a product on the weigh platter.
The weight is measured but the fixed price stays same.
UNI-5 User’s Manual 2-5
Page 27
Chapter 2 LABEL ISSUE
7.
When “MANUAL” is set in the Print Mode,
Press the [PRINT] key on the key sheet.
Non-traceable products Traceable products
When “AUTO” is set in the Print Mode,
The label is automatically issued as soon as the weighing is stabilized.
Non-traceable products Traceable products
2-6 UNI-5 User’s Manual
Page 28
Chapter 2 LABEL ISSUE
2.1.3 PROCESSING FIXED PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
When the product is preset as a traceable item, the traceability screen appears.
See Chapter 4 for more details about traceability products.
4.
The selected PLU screen appears.
5.
See Chapter 5 for more details about temporary change operations.
UNI-5 User’s Manual 2-7
Page 29
Chapter 2 LABEL ISSUE
6.
Press the [PRINT] key on the key sheet to issue the labels.
The label is issued.
Non-traceable products Traceable products
Remove the label.
The next label is issued.
Non-traceable products Traceable products
Note: To stop printing, press the [PRINT] key again.
2-8 UNI-5 User’s Manual
Page 30
Chapter 2 LABEL ISSUE
2.1.4 PROCESSING FIXED WEIGHT/FIXED UNIT PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
When the product is preset as a traceable item, the traceability screen appears.
See Chapter 4 for more details about traceability products.
4.
The selected PLU screen appears.
5.
See Chapter 5 for more details about temporary change operations.
UNI-5 User’s Manual 2-9
Page 31
Chapter 2 LABEL ISSUE
6.
Enter the fixed weight using the numeric keys on the key sheet and press the “FIXED
WEIGHT” field.
EXAMPLE Fixed weight “858g”
7.
Press the [PRINT] key on the key sheet to issue the labels.
The label is issued.
Non-traceable products Traceable products
Remove the label.
The next label is issued.
Non-traceable products Traceable products
Note: To stop printing, press the [PRINT] key again.
2-10 UNI-5 User’s Manual
Page 32
Chapter 2 LABEL ISSUE
2.2 LABEL ISSUE WITH OPERATORS
2.2.1 WEIGHING UNIT PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
When the product is preset as a traceable item, the traceability screen appears.
See Chapter 4 for more details about traceability products.
4.
The selected product screen appears.
Without Preset Tare Weight
With Preset Tare Weight
UNI-5 User’s Manual 2-11
Page 33
Chapter 2 LABEL ISSUE
Manual Tare Entry
To newly enter a tare weight or overwrite an existing tare weight, enter the tare weight
using the numeric keys and press the “TARE” field on the screen.
EXAMPLE Tare weight “50g”
5.
See Chapter 5 for more details about temporary change operations.
6.
Put a product on the weigh platter.
The weight is measured and the total price is calculated.
2-12 UNI-5 User’s Manual
Page 34
Chapter 2 LABEL ISSUE
7.
Press a operator button on the screen to issue the label.
EXAMPLE Operator “BETTY”
The label is issued.
UNI-5 User’s Manual 2-13
Page 35
Chapter 2 LABEL ISSUE
2.2.2 WEIGHING FIXED PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
When the product is preset as a traceable item, the traceability screen appears.
See Chapter 4 for more details about traceability products.
4.
The selected product screen appears.
Without Preset Tare Weight
2-14 UNI-5 User’s Manual
Page 36
Chapter 2 LABEL ISSUE
With Preset Tare Weight
Manual Tare Entry
To newly enter a tare weight or overwrite an existing tare weight, enter the tare weight
using the numeric keys and press the “TARE” field on the screen.
EXAMPLE Tare weight “50g”
5.
See Chapter 5 for more details about temporary change operations.
6.
Put a product on the weigh platter.
The weight is measured and the total price is calculated.
UNI-5 User’s Manual 2-15
Page 37
Chapter 2 LABEL ISSUE
7.
Press a operator button on the screen to issue the label.
EXAMPLE Operator “BETTY”
The label is issued.
2-16 UNI-5 User’s Manual
Page 38
Chapter 2 LABEL ISSUE
2.2.3 PROCESSING FIXED PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
When the product is preset as a traceable item, the traceability screen appears.
See Chapter 4 for more details about traceability products.
4.
The selected PLU screen appears.
5.
See Chapter 5 for more details about temporary change operations.
UNI-5 User’s Manual 2-17
Page 39
Chapter 2 LABEL ISSUE
6.
Press a operator button on the screen to issue the label.
EXAMPLE Operator “BETTY”
The label is issued.
2-18 UNI-5 User’s Manual
Page 40
Chapter 2 LABEL ISSUE
2.2.4 PROCESSING FIXED WEIGHT/FIXED UNIT PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU No.6 “Roast Beef”
Î
or
3.
When the product is preset as a traceable item, the traceability screen appears.
See Chapter 4 for more details about traceability products.
4.
The selected PLU screen appears.
5.
See Chapter 5 for more details about temporary change operations.
UNI-5 User’s Manual 2-19
Page 41
Chapter 2 LABEL ISSUE
6.
Enter the fixed weight using the numeric keys on the key sheet and press the “FIXED
WEIGHT” field.
EXAMPLE Fixed weight “858g”
7.
Press a operator button on the screen to issue the label.
EXAMPLE Operator “BETTY”
The label is issued.
2-20 UNI-5 User’s Manual
Page 42
Chapter 3 RECEIPT ISSUE
RECEIPT ISSUE
3.1 SALES BY THE SAME OPRATOR
1.
Ensure that the initial screen is displayed.
2-1
Select a desired product category by pressing the corresponding field on the screen.
EXAMPLE Select “Meat” category.
2-2
The PLU preset screen for the selected category appears.
Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the
key sheet, or simply press a preset key on the screen where a desired product is
allocated.
EXAMPLE Select PLU No.1 “Rib Steak”.
Î
or
3
UNI-5 User’s Manual 3-1
Page 43
Chapter 3 RECEIPT ISSUE
2-3
The PLU screen appears.
Weighing Unit Price PLU
2-4
Put a product on the weigh platter.
2-5
Press a button on the screen for the operator who has sold the product.
EXAMPLE Select “Operator 002”.
3-2 UNI-5 User’s Manual
Page 44
Chapter 3 RECEIPT ISSUE
2-6
The subtotal for the selected operator is shown on the screen.
3-1
Select a desired product category by pressing the corresponding field on the screen.
EXAMPLE Select “Fish” category.
3-2
The PLU preset screen for the selected category appears.
Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the
key sheet, or simply press a preset key on the screen where a desired product is
allocated.
EXAMPLE Select PLU No.102 “Maine Lobster”.
Î
or
UNI-5 User’s Manual 3-3
Page 45
Chapter 3 RECEIPT ISSUE
3-3
The PLU screen appears.
Fixed Price PLU
3-4
Press a button on the screen for the operator who has sold the product.
EXAMPLE Select “Operator 002”.
3-5
The subtotal for the selected operator is shown on the screen.
4-1
Select a desired product category by pressing the corresponding field on the screen.
EXAMPLE Select “Bakery” category.
3-4 UNI-5 User’s Manual
Page 46
Chapter 3 RECEIPT ISSUE
4-2
The PLU preset screen for the selected category appears.
Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the
key sheet, or simply press a preset key on the screen where a desired product is
allocated.
EXAMPLE Select PLU No.201 “Live Wild Cherry Clam”.
Î
or
4-3
The PLU screen appears.
Weighing Fixed Price PLU
4-4
Put a product on the weigh platter.
UNI-5 User’s Manual 3-5
Page 47
Chapter 3 RECEIPT ISSUE
4-5
Press a button on the screen for the operator who has sold the product.
EXAMPLE Select “Operator 002”.
4-6
The subtotal for the selected operator is shown on the screen.
5-1
Select a desired product category by pressing the corresponding field on the screen.
EXAMPLE Select “Meat” category.
5-2
The PLU preset screen for the selected category appears.
Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the
key sheet, or simply press a preset key on the screen where a desired product is
allocated.
3-6 UNI-5 User’s Manual
Page 48
Chapter 3 RECEIPT ISSUE
EXAMPLE Select PLU No.4 “Pork Chops”.
Î
or
5-3
The PLU screen appears.
Fixed Unit Price PLU
5-4
Enter the weight using the numeric keys on the key sheet, and press the “Fixed Weight”
field on the screen.
EXAMPLE Weight “400g”
UNI-5 User’s Manual 3-7
Page 49
Chapter 3 RECEIPT ISSUE
5-5
Press a button on the screen for the operator who has sold the product.
EXAMPLE Select “Operator 002”.
5-6
The subtotal for the selected operator is shown on the screen.
6.
Press the subtotal field on the screen to display more detailed subtotal data.
7.
The detailed subtotal screen appears for confirmation of product registrations.
Then, confirm that the detail of the transaction is correct.
3-8 UNI-5 User’s Manual
Page 50
Chapter 3 RECEIPT ISSUE
8.
Press the [PRINT] key on the key sheet to issue the receipt.
UNI-5 User’s Manual 3-9
Page 51
Chapter 3 RECEIPT ISSUE
9.
The Subtotal screen appears for the settlement.
3-10 UNI-5 User’s Manual
Page 52
Chapter 3 RECEIPT ISSUE
3.2 SALES BY DIFFERENT OPRATORS
1.
Ensure that the initial screen is displayed.
2-1
EXAMPLE Product registration by “Operator 002”
Select a desired product category by pressing the corresponding field on the screen.
EXAMPLE Select “Meat” category.
2-2
The PLU preset screen for the selected category appears.
Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the
key sheet, or simply press a preset key on the screen where a desired product is
allocated.
EXAMPLE Select PLU No.1 “Rib Steak”.
Î
or
UNI-5 User’s Manual 3-11
Page 53
Chapter 3 RECEIPT ISSUE
2-3
The PLU screen appears.
Weighing Unit Price PLU
2-4
Put a product on the weigh platter.
2-5
Press a button on the screen for the operator who has sold the product.
EXAMPLE Select “Operator 002”.
3-12 UNI-5 User’s Manual
Page 54
Chapter 3 RECEIPT ISSUE
2-6
The subtotal for the selected operator is shown on the screen.
3-1
EXAMPLE Product registration by “Operator 002”
Select a desired product category by pressing the corresponding field on the screen.
EXAMPLE Select “Fish” category.
3-2
The PLU preset screen for the selected category appears.
Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the
key sheet, or simply press a preset key on the screen where a desired product is
allocated.
EXAMPLE Select PLU No.102 “Maine Lobster”.
Î
or
UNI-5 User’s Manual 3-13
Page 55
Chapter 3 RECEIPT ISSUE
3-3
The PLU screen appears.
Fixed Price PLU
3-4
Press a button on the screen for the operator who has sold the product.
EXAMPLE Select “Operator 002”.
3-5
The subtotal for the selected operator is shown on the screen.
4-1
EXAMPLE Product registration by “Operator 001”
Select a desired product category by pressing the corresponding field on the screen.
EXAMPLE Select “Bakery” category.
3-14 UNI-5 User’s Manual
Page 56
Chapter 3 RECEIPT ISSUE
4-2
The PLU preset screen for the selected category appears.
Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the
key sheet, or simply press a preset key on the screen where a desired product is
allocated.
EXAMPLE Select PLU No.201 “Live Wild Cherry Clam”.
Î
or
4-3
The PLU screen appears.
Weighing Fixed Price PLU
4-4
Put a product on the weigh platter.
UNI-5 User’s Manual 3-15
Page 57
Chapter 3 RECEIPT ISSUE
4-5
Press a button on the screen for the operator who has sold the product.
EXAMPLE Select “Operator 001”.
4-6
The subtotal for the selected operator is shown on the screen.
5-1
EXAMPLE Product registration by “Operator 002”
Select a desired product category by pressing the corresponding field on the screen.
EXAMPLE Select “Meat” category.
3-16 UNI-5 User’s Manual
Page 58
Chapter 3 RECEIPT ISSUE
5-2
The PLU preset screen for the selected category appears.
Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the
key sheet, or simply press a preset key on the screen where a desired product is
allocated.
EXAMPLE Select PLU No.4 “Pork Chops”.
Î
or
5-3
The PLU screen appears.
Fixed Unit Price PLU
5-4
Enter the weight using the numeric keys on the key sheet, and press the “Fixed Weight”
field on the screen.
EXAMPLE Weight “400g”
UNI-5 User’s Manual 3-17
Page 59
Chapter 3 RECEIPT ISSUE
5-5
Press a button on the screen for the operator who has sold the product.
EXAMPLE Select “Operator 002”.
5-6
The subtotal for the selected operator is shown on the screen.
6.
Press the subtotal field on the screen to display more detailed subtotal data.
7.
The detailed subtotal screen appears for confirmation of product registrations.
Then, confirm that the detail of the transaction is correct.
3-18 UNI-5 User’s Manual
Page 60
Chapter 3 RECEIPT ISSUE
8.
Press the [PRINT] key on the key sheet to issue the receipt.
9.
The Subtotal screen appears for the settlement.
UNI-5 User’s Manual 3-19
Page 61
Chapter 3 RECEIPT ISSUE
10-1
EXAMPLE Product registration by “Operator 001”
Select a desired product category by pressing the corresponding field on the screen.
EXAMPLE Select “Meat” category.
10-2
The PLU preset screen for the selected category appears.
Then, enter a desired PLU number using the numeric keys and press the [PLU] key on
the key sheet, or simply press a preset key on the screen where a desired product is
allocated.
EXAMPLE Select PLU No.3 “Round Steak”.
Î
or
10-3
The PLU screen appears.
Weighing Unit Price PLU
3-20 UNI-5 User’s Manual
Page 62
Chapter 3 RECEIPT ISSUE
10-4
Put a product on the weigh platter.
10-5
Press a button on the screen for the operator who has sold the product.
EXAMPLE Select “Operator 001”.
10-6
The subtotal for the selected operator is shown on the screen.
UNI-5 User’s Manual 3-21
Page 63
Chapter 3 RECEIPT ISSUE
11
EXAMPLE Receipt issue by “Operator 001”
Press the subtotal field on the screen to display more detailed subtotal data.
12
The Subtotal screen appears for confirmation of product registrations.
13
Press the [PRINT] key on the key sheet to issue the receipt.
3-22 UNI-5 User’s Manual
Page 64
Chapter 3 RECEIPT ISSUE
14
The Subtotal screen appears for the settlement.
UNI-5 User’s Manual 3-23
Page 65
Chapter 3 RECEIPT ISSUE
3.3 VOIDING PRODUCT REGISTRATION
1.
To void a product registration that has been made in the transaction, display the Subtotal
screen for confirmation of product registrations.
2.
Press to select a desired product registration field.
EXAMPLE Void the third item.
Note: To scroll the selection up or down, press the [c] or [d] keys on the key sheet.
3.
Press the [VOID] button on the screen.
4.
The confirmation screen appears. Then, press the [EXEC] button for execution.
3-24 UNI-5 User’s Manual
Page 66
Chapter 3 RECEIPT ISSUE
5.
The selected item has been voided.
6.
Press the [PRINT] key on the key sheet to issue the receipt.
Deleted by a dashed line
UNI-5 User’s Manual 3-25
Page 67
Chapter 3 RECEIPT ISSUE
7.
The Subtotal screen appears for the settlement.
3-26 UNI-5 User’s Manual
Page 68
Chapter 4 TRACEABILITY PRODUCTS
TRACEABILITY PRODUCTS
4.1 REFERING TO PREVIOUS TRACEABILITY DATA
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU number “6”.
Î
or
3.
When the product is preset as a traceable item, the Traceability screen appears.
4
UNI-5 User’s Manual 4-1
Page 69
Chapter 4 TRACEABILITY PRODUCTS
4.
To refer to the previously processed traceability data, press the [LIST] button.
5.
The Traceability History screen appears. Then, press to select a desired data field.
6.
The selected data appears. Then, press the [SET] button.
7.
The selected PLU screen appears.
Weighing Unit Price Products
4-2 UNI-5 User’s Manual
Page 70
Chapter 4 TRACEABILITY PRODUCTS
Fixed Price Products
Fixed Unit Price Products
Weighing Fixed Price Products
UNI-5 User’s Manual 4-3
Page 71
Chapter 4 TRACEABILITY PRODUCTS
4.2 CHANGING TRACEABILITY DATA
1.
Ensure that the initial screen is displayed.
2.
Enter a desired PLU number using the numeric keys and press the [PLU] key on the key
sheet, or simply press a preset key on the screen where the product is allocated.
EXAMPLE PLU number “6”.
Î
or
3-1
When the product is preset as a traceable item, the Traceability screen appears.
Then, confirm whether information on the screen is correct or not.
When the data is correct, press the [SET] button.
4-4 UNI-5 User’s Manual
Page 72
Chapter 4 TRACEABILITY PRODUCTS
3-2
If the data is not correct, press to select a desired data field.
EXAMPLE Select “France”.
EXAMPLE Change to “Argentina”.
The data has been changed.
To change the “FACTORY” data, press the corresponding field.
Press to select a desired data field.
UNI-5 User’s Manual 4-5
Page 73
Chapter 4 TRACEABILITY PRODUCTS
The data has been changed. Then, press the [SET] button.
4.
When changing the lot data, press the “LOT” filed.
The Traceability Lot Number Set screen appears.
Change the lot number using the [ABC] [ERASE] and [BACK SPACE] buttons, and press
the [BACK] button to finish.
4-6 UNI-5 User’s Manual
Page 74
Chapter 4 TRACEABILITY PRODUCTS
The confirmation screen appears. Then, press the [SAVE] button to save the data.
The Traceability screen appears. Then, press the [SET] button.
5.
The selected PLU screen appears.
Weighing Unit Price Products
Fixed Price Products
UNI-5 User’s Manual 4-7
Page 75
Chapter 4 TRACEABILITY PRODUCTS
Fixed Unit Price Products
Weighing Fixed Price Products
4-8 UNI-5 User’s Manual
Page 76
Chapter 5 TEMPORARY CHANGE OPERATIONS
TEMPORARY CHANGE OPERATIONS
5.1 UNIT PRICE CHANGE
1.
Ensure that the selected PLU screen is displayed.
Weighing Products
Fixed Unit Price Products
2.
Enter a desired unit price using the numeric keys and press the “UNIT PRICE” or “FIXED
UNIT PRICE” field.
EXAMPLE “$3.80”
.
Weighing Products
5
UNI-5 User’s Manual 5-1
Page 77
Chapter 5 TEMPORARY CHANGE OPERATIONS
Fixed Unit Price Products
5-2 UNI-5 User’s Manual
Page 78
Chapter 5 TEMPORARY CHANGE OPERATIONS
5.2 FIXED PRICE CHANGE
1.
Ensure that the selected PLU screen is displayed.
Fixed Price Products
Weighing Fixed Price Products
2.
Enter a desired price using the numeric keys, and press the “FIXED PRICE” field.
EXAMPLE “$3.80”
.
Fixed Price Products
UNI-5 User’s Manual 5-3
Page 79
Chapter 5 TEMPORARY CHANGE OPERATIONS
Weighing Fixed Price Products
5-4 UNI-5 User’s Manual
Page 80
Chapter 5 TEMPORARY CHANGE OPERATIONS
5.3 AMOUNT DISCOUNT FOR UNIT PRICE
1.
Ensure that the selected PLU screen is displayed.
Weighing Unit Price Products
Fixed Unit Price Products
2.
Enter a desired discount amount using the numeric keys, and press the “-$ (U/P)” field.
EXAMPLE Discount amount “$1.00”.
Weighing Unit Price Products
UNI-5 User’s Manual 5-5
Page 81
Chapter 5 TEMPORARY CHANGE OPERATIONS
Fixed Unit Price Products
5-6 UNI-5 User’s Manual
Page 82
Chapter 5 TEMPORARY CHANGE OPERATIONS
5.4 PERCENT DISCOUNT FOR UNIT PRICE
1.
Ensure that the selected PLU screen is displayed.
Weighing Unit Price Products
Fixed Unit Price Products
2.
Enter a desired discount percentage using the numeric keys on the key sheet, and press
the “-% (U/P)” field.
EXAMPLE Discount percentage “10%”.
UNI-5 User’s Manual 5-7
Page 83
Chapter 5 TEMPORARY CHANGE OPERATIONS
Fixed Unit Price Products
5-8 UNI-5 User’s Manual
Page 84
Chapter 5 TEMPORARY CHANGE OPERATIONS
5.5 AMOUNT DISCOUNT FOR TOTAL PRICE
1.
Ensure that the selected PLU screen is displayed.
Fixed Price Products
Weighing Fixed Price Products
2.
Enter a desired discount amount using the numeric keys, and press the “-$” field.
EXAMPLE Discount amount “$1.00”.
Fixed Price Products
UNI-5 User’s Manual 5-9
Page 85
Chapter 5 TEMPORARY CHANGE OPERATIONS
Weighing Fixed Price Products
5-10 UNI-5 User’s Manual
Page 86
Chapter 5 TEMPORARY CHANGE OPERATIONS
5.6 PERCENT DISCOUNT FOR TOTAL PRICE
1.
Ensure that the selected PLU screen is displayed.
Fixed Price Products
Weighing Fixed Price Products
2.
Enter a desired discount percentage using the numeric keys on the key sheet, and press
the “-%” field.
EXAMPLE Discount percentage “10%”.
UNI-5 User’s Manual 5-11
Page 87
Chapter 5 TEMPORARY CHANGE OPERATIONS
Weighing Fixed Price Products
5-12 UNI-5 User’s Manual
Page 88
Chapter 5 TEMPORARY CHANGE OPERATIONS
5.7 PRODUCT QUANTITY CHANGE
1.
Ensure that the selected PLU screen is displayed.
Fixed Price Products
2.
Enter a desired quantity using the numeric keys, and press the “PCS” field.
EXAMPLE Quantity “2 pieces”
.
3.
To select a desired fix price mark, press the “PCS” field again.
UNI-5 User’s Manual 5-13
Page 89
Chapter 5 TEMPORARY CHANGE OPERATIONS
4.
The Fix Price mark List screen appears. Then, select a desired mark by pressing the
corresponding field.
EXAMPLE Price mark “PC. PCS.”
5-14 UNI-5 User’s Manual
Page 90
Chapter 5 TEMPORARY CHANGE OPERATIONS
5.8 PRINT QUANTITY SETTING
1.
Ensure that the selected PLU screen is displayed and “AUTO” is selected in the Printing
Mode.
Fixed Price Products
2.
Enter a desired number of labels and press the “PRN QTY (Print Quantity)” field on the
screen.
EXAMPLE Print quantity “3”.
3.
Press the [PRINT] key on the key sheet.
The set number of labels will be issued.
Note: To interrupt the issue of labels, press the [PRINT] key again.
To continue the issue of labels, press the [PRINT] key again.
UNI-5 User’s Manual 5-15
Page 91
Chapter 6 SELF-SERVICE OPERATIONS
SELF-SERVICE OPERATIONS
6.1 WEIGHING PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Select a desired product by pressing the corresponding button on the screen.
EXAMPLE Select “Roast Beef”
3.
The selected product screen appears.
6
UNI-5 User’s Manual 6-1
Page 92
Chapter 6 SELF-SERVICE OPERATIONS
4.
Put a product on the weigh platter.
The weight is measured and the total price is calculated.
5.
Press the [LABEL PRINT] button on the screen to issue the label.
The label is issued.
6-2 UNI-5 User’s Manual
Page 93
Chapter 6 SELF-SERVICE OPERATIONS
6.2 FIXED PRICE PRODUCTS
1.
Ensure that the initial screen is displayed.
2.
Select a desired product by pressing the corresponding button on the screen.
EXAMPLE Select “Roast Beef”
3.
The selected product screen appears.
Then, press the [LABEL PRINT] button on the screen to issue the label.
The label is issued.
UNI-5 User’s Manual 6-3
Page 94
Chapter 7 ACCUMULATOR MODE
ACCUMULATOR MODE
7.1 MANUAL INPUT ACCUMULATION
1.
To get the Operation Menu Select screen, press the [MODE] key on the key sheet.
Then, press the “ACC (Accumulator)” filed.
2.
The Accumulator (Input Number Accumulation) screen appears.
3.
Enter a desired PLU number and press the [PLU] key on the key sheet.
EXAMPLE PLU number “6”.
Î
The Input Number Accumulation screen for the selected product appears.
7
UNI-5 User’s Manual 7-1
Page 95
Chapter 7 ACCUMULATOR MODE
4.
Enter a quantity, weight, and price that are to be accumulated and press the
corresponding fields for registration. Then, press the [ACC] button on the screen.
EXAMPLE Quantity “1 pc.”, Weight “169g”, Price “$0.84”
5.
The confirmation screen appears. Then, press the [EXEC] button on the screen.
6.
The registration has been completed.
7-2 UNI-5 User’s Manual
Page 96
Chapter 7 ACCUMULATOR MODE
7.2 WEIGHING ACCUMULATION
1.
To get the Operation Menu Select screen, press the [MODE] key on the key sheet.
Then, press the “ACC (Accumulator)” filed.
2.
To get the Weighing Accumulation screen, press the [WGT. ACC] tab.
UNI-5 User’s Manual 7-3
Page 97
Chapter 7 ACCUMULATOR MODE
3.
Enter a desired PLU number and press the [PLU] key on the key sheet.
EXAMPLE PLU number “6”.
Î
The Weighing Accumulation screen for the selected product appears.
4.
Put a product on the weigh platter and press the [ACC] button on the screen..
5.
The confirmation screen appears. Then, press the [EXEC] button on the screen.
7-4 UNI-5 User’s Manual
Page 98
Chapter 7 ACCUMULATOR MODE
6.
Remove the product from the weigh platter.
UNI-5 User’s Manual 7-5
Page 99
Chapter 7 ACCUMULATOR MODE
7.3 MANUAL INPUT VOID
1.
To get the Operation Menu Select screen, press the [MODE] key on the key sheet.
Then, press the “ACC (Accumulator)” filed.
2.
To get the Input Number Void screen, press the [NUM. VOID] tab.
7-6 UNI-5 User’s Manual
Page 100
Chapter 7 ACCUMULATOR MODE
3.
Enter a desired PLU number and press the [PLU] key on the key sheet.
EXAMPLE PLU number “6”.
Î
The Input Number Void screen for the selected product appears.
4.
Enter a quantity , weight, and price that are to be voided and press the corresponding fields
for registration. Then, press the [VOID] button on the screen.
EXAMPLE Quantity “1 pc.”, Weight “169g”, Price “$0.84”
5.
The confirmation screen appears. Then, press the [EXEC] button on the screen.
UNI-5 User’s Manual 7-7
Loading...