INSTALLATION INSTRUCTIONS: VERTICAL WALL BED HARDWARE KIT WITH FRAME
MODEL CODES:
54877 (Single vertical wall bed)
55991 (Double vertical wall bed)
54386 (Queen vertical wall bed)
*Our more compact model for shipping.
Rockler Woodworking and Hardware 4365 Willow Drive, Medina, MN 55340
1-800-279-4441
1
HARDWARE
A
B
C
D
E
F
G
H
I
Left and right of the frame
Upper and lower half frame supports
Middle frame supports
Long center frame support
Upper and lower frame supports
Flat bars
Pistons (non locking)
Mattress Supports
Mounting plates (left and right)
x2 x2 x2
x4 x4 x4
x2 x2 x2
x1 x1 x1
x2 x2 x2
x2 x2 x2
x2 x2 x2
x1 x2 x2
x2 x2 x2
J
K
L
M
N
O
P
Q
Saddle locking plates
Brackets to attach wall bed to wall
Door brackets
Legs (left and right)
Tube (for attaching legs)
Slats
Slat caps
Double slat caps
x2 x2 x2
x2 x2 x2
x6 x12 x12
x2 x2 x2
x1 x1 x1
x40 x40 x42
x40 x40 x42
x20 x20 x21
2
R
Wrench
x1 x1 x1
S1
S2
T
U
V
W
X
Y
Z
Allen Key #4
Allen Key #5
Threaded inserts
M8 x 16mm Screws
#10 x 55mm Screws (Step 12)
#8 x 15mm Screws (Steps 11-12)
#10 x 15mm Screws
#10 x 30mm Screws
M5 x 15mm Screws
x1 x1 x1
x1 x1 x1
x16 x16 x16
x16 x16 x16
x26 x26 x26
x32 x52 x52
x4 x4 x4
x4 x4 x4
x2 x2 x2
AA
BB
CC
DD
EE
FF
GG
M6 x 30mm Bolts
M8x 50mm Bolts
Washers
Nylon Washers (for pivoting legs)
M5 Nuts (for saddle locks)
M8 Locking nuts
Temporary stoppers
x4 x4 x4
x34 x34 x34
x8 x8 x8
x4 x4 x4
x2 x2 x2
x40 x40 x40
x2 x2 x2
3
*All measurements are for 19mm (3/4'') board
E
Single
E E
Double
E E
Queen
A= Exterior
B-C-D-E = Inset
78 1/2
83 1/2
in
41 3/8
57 1/4
63 5/16
in
14 1/2
14 1/2
14 1/2
in
77
## #########
## #########
in
Queen
Outside Measurements
Width
Depth
Height
Single
Double
42 7/8
58 3/4
64 13/16
in
## #########
## #########
## #########
in
78 1/2
VERTICAL WALL BED
Conversion Table
DIMENSIONS
3/4''
Panels
Queen
Inside Measurements
Width
Depth
Height
Single
Double
A
D
A
A
B
C
B
E
F
Overall Cabinet Dimensions
Cabinet Parts Dimension Guide
B
C
D
A
B
4
* Suggested dimensions
DRILLING GUIDE
The holes should be 3/8” in
diameter and 1/2” deep for
threaded inserts.
"
1
2
2
"
1
2
2
Back
Front
"
3
4
7
15
6
"
16
"
1
8
6
1
3
"
8
"
7
16
11
All measurements are for 3/4’’ thick board.
Bottom
7
9
"
16
"
"
7
8
7
16
13
11
*See full sized template in product box.
"
3
4
17
5
1
INSTALLING THE MOUNTING BRACKETS
S2
Left side
Front
Front
Right side
Bottom
U
I
T
Wood
x16
x2
x16
I
U + T
2
ASSEMBLING THE CABINET
* See guide on page 4 for suggested cabinet dimensions.
6
3
SECURING TO THE WALL
Y
* Professional installation recommended.
X=
Y=
CC=
K=
* Needs to be secured into at least
two wood or metal studs.
*Nylon wall anchors are NOT recommended
x4
x4
x8
x2
X
4
ASSEMBLING THE FRAME
4.1
Attach B and C to A for both the
right and left sides of the frame.
FF=
BB=
A=
B=
C=
x12
x12
x2
x4
x2
S
B
A
C
*Ensure that all of the tabs are
pointing towards each other.
These tabs should be at on the ground.
B
7
4.2
Attach E and F to D.
F
E
FF=
BB=
D=
E=
F=
x4
x4
x2
x1
x2
D
All tabs should be facing the oor.
E
F
The tabs on E must face the inside
of the frame.
4.3
Insert E into the assemblies from
step 4.1.
FF=
BB=
x6
x6
8
4.4
Bolt F to the two frame halves from
step 4.1.
FF=
BB=
5
x12
x12
INSTALLING THE SLATS
P
O
Q
x36
x36
x18
Q
O
P
O
Place P on one end of each slat. Attach two slats together with Q.
Insert P and Q into their designated holes along the
frame. Insert all of the slats except for 4 for the single
and double, and 6 for the queen (please see next page
to see which slats to skip).
*If necessary, use a rubber mallet to secure the slats
into the frame.
9
Example below works for both
single and double.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Pivot point
Start from this side.
Please do not insert slats in row 11 for the queen
For each bed size, do not insert
slats in row #8, or the slats in the
last row. For the queen size, please
do not insert slats in row #11 as
well.
ATTACHING THE PISTONS TO THE FRAME
6
Pivot point
#8
Last
FF
FF=
Secure the longer metal ends of the pistons to the frame.
This end
x2
G=
x2
10
7
INSTALLING THE FRAME ONTO THE MOUNTING BRACKETS
Place the bearing into the saddle on the mounting
bracket. Secure the bearing in place with:
Z
EE
x2
J
x2
x2
11
8
INSTALLING THE PISTONS TO THE CABINET
Tilt the frame inside past the edge of the cabinet to install the pistons
on the mounting brackets.
9
FF
INSTALLING THE STOPPER
Stopper
x2
Install the temporary stoppers GG onto the
top corners of the bed cabinet.
GG
Install the permanent stopper on the inside top of
the cabinet where it will allow for the door to close
ush to the front of the cabinet.
x2
12
10
INSTALLING THE LEGS
FF
DD
M
AA
x2
x4
10.1
N
Secure the legs to the bed frame.
Do not overtighten.
10.2
Install tube to both legs.
M
INSTALLING THE DOOR BRACKETS
AA
11
The door brackets must point downward. Install the door brackets
in alignment with the support bars on the bed frame.
* Install the handle on the other side of the door during this step.
Decorative handle not included. Handle should be mounted
at a height to comfortably allow the user to pull the bed down
(approximately 1/3 of the way down from the top of the door).
Measurements (right) are for the
placement of this hole on the
backside of the doors.
AA
S1
6”
Top
x4
6”
10
27
3/8”
5/16”
10
30
3/8”
3/4”
W
L
x12
x 6
x 24
x12
Bottom
27
5/16”
30
3/4”
13
12
INSTALLING THE DOORS
12.1
Hook the door brackets onto the frame and push down until they are
rmly in place. Center the doors on the frame.
For this step
W
V
x 2
12.2
Attach the doors to the frame while putting weight on the frame to keep the bed
open. We recommend to have someone else sit on the frame during this step.
* The bed will not stay open on its own without the weight of a mattress.
14
W
V
x 20
x 26
x 28
x 26
13
INSTALLING THE REMAINING SLATS
P
O
Q
Insert P and Q into their designated holes along the
frame. Insert all of the remaining slats.
x4
x4
x2
x6
x6
x3
Q
O
P
O
14
INSTALLING THE MATTRESS SUPPORTS
Insert the mattress supports into the
designated holes on the bed frame.
H
x 1
x 2
H
15
USING THE WALL BED
The wall bed is assembled and shown in
lowered position.
.
sure that the leg is fully retracted.
Pull up gently to close. The leg serves as a mattress
retaining system. The pistons insure that the door
closes properly and remains closed.
Pivot the leg towards the inside of the unit. Make
16
Bed Size
Single
Double
Queen
RCKLR100KD-R2
* The bed will not stay open on its own without the weight of a mattress.
Mattress Size
*Mattress not included
39” x 75’’
54” x 75’’
60” x 80‘’
Thickness
10”
Load Rating
Dynamic
136 kg (300 lbs)
154 kg (340 lbs)
.
454 kg (1000 lbs)
Static
181 kg (400 lbs)
Loading...