BUNK BED
Examine all packaging material for small parts that may have come loose during shipment. Periodic checks are recommended to insure that all
components are in proper position, tight and free from damage. Keep this assembly instruction for future reference. Adult assembly is required.
This product is designed for residential use only.
HARDWARE LIST
A
B
C
D
E
F
G
H
Long Bolt 6.3x80
(16)
Half Round Nut
(16)
Short Bolt 6.3x35
(4)
Short Screw Bolt 7x80
(8)
Screw 4x35
(62)
Allen Key
(1)
Screw 4x25
(16)
Long Screw Bolt 7x100
(16)
Wood Connect 010x40
I
(24)
QTYPAR T
16A
4C
HARDWARE QTYPAR T HARDWARE
B
D
16
8
Page 1 of 4
PIECES LIST
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Front Post
(2)
Back Post
(2)
Upper Panel
(2)
Lower Panel
(2)
Upper Front Rail
(1)
Back Rail
(2)
Guard Rail
(4)
Upper Slats
(1)
Lower Slats
(1)
Ladder
(1)
Guard Rail Supports
(2)
Lower Front Rail
(1)
Side DRW Panels
(4)
Back DRW Panels
(2)
Bottom DRW Panels
(2)
Front DRW Panels
(2)
STEP 1
Begin assembly by connecting
the Back Post (K) to the Upper
and Lower Panels (L & M) with 2
Long Screw Bolts (H) for each.
Then attach the Front Post
Headboard & Footboard (J) to the
Upper and Lower Headboard &
Footboards (L & M) with 2 Long
Screw Bolts (H) for each.
Finished piece seen in Figure 1.
62E
16G
24I
TEAMWORK NEEDED
FOR ASSEMBLY
H
M
H
L
F
1
16H
H
H
H
H
K
H
J
H
STEP 2
Repeat the instructions from step 1 to assemble
the second side.
CARE & MAINTENANCE
as they may cause damage to the finish. Periodic checks are recommended to make sure that all bolts, screws and nuts are securely tightened.
:
The touch of a soft cloth is all the maintenance the finish will ever need. Please do not use harsh or abrasive cleaners for polishing,
FIGURE 1
J
K
BUNK BED
FIGURE 2
B
I
P
P
P
O
D
II
O
I
K
A
I
N
D
D
A
STEP 3
Next attach the top
Guard Rails (P) to the
Back Post (K) by first
inserting 2 Wood Dowels
(I) into place in the upper
D
and lower holes and then
A
securing them with a
Short Screw Bolt (D) in
the middle hole for each
side. See Figure 2.
Page 2 of 4
U
O
AA
A
STEP 4
Attach the Back Rails
(O) to the Back Post
Headboard & Footboard
(K) using 2 Long Bolts (A).
See Figure 2.
STEP 5
Repeat steps 1-5 to secure the
remaining panel to all the rails.
A
T
E
STEP 6
Attach the Upper Front Rail (N) and
the Lower Front Rail (U) with 2 Long
Bolts (A) on to the Front Post Headboard &
Footboard (J).
STEP 7
Attach the Top Guard Rails (P) to the Front Post (J) by inserting 2 Wood
Dowels (I) into place in the upper and lower holes and then securing them
with a Short Screw Bolt (D) in the middle hole for each side.
E
E
S
E
E
E
STEP 8
Attach the Guard Rail Supports (T) to the Rails with 3 Long Screws (E).
STEP 9
Attach the Ladder (S) to the Upper Front Rail (N) and Lower
Front Rail (U) by using 2 Short Bolts (C). See Figure 3.
S
N
FIGURE 3
C
Figure 3 shown from
the reverse side of drawing.
CARE & MAINTENANCE
as they may cause damage to the finish. Periodic checks are recommended to make sure that all bolts, screws and nuts are securely tightened.
:
The touch of a soft cloth is all the maintenance the finish will ever need. Please do not use harsh or abrasive cleaners for polishing,
FIGURE 4
BUNK BED
Page 3 of 4
Q
E
O
N
U
R
Q
O
O
STEP 10
Next attach the Lower Slats (R)
to the Bottom Back Rail (O) and
the Lower Front Rail (U) by using
2 Long Screws (E) for each slat.
STEP 11
Attach the Upper Slats (Q) to the
Upper Back Rail (O) and the
Upper Front Rail (N) by using 2
Long Screws (E) for each slat.
See Figure 4.
G
X
G
STEP 12
Attach the Side DRW
Panels (V) to the Back
DRW Panel (W) by using 2
Short Screws (G).
STEP 13
Attach the Bottom DRW
Panel (X) to the drawer
assembly by sliding it into
place until it sits firmly in the
groove on the insdie of the
Back DRW Panel (W).
CARE & MAINTENANCE
as they may cause damage to the finish. Periodic checks are recommended to make sure that all bolts, screws and nuts are securely tightened.
:
The touch of a soft cloth is all the maintenance the finish will ever need. Please do not use harsh or abrasive cleaners for polishing,
V
W
G
G
W
V
Y
BUNK BED
Page 4 of 4
G
STEP 14
Next place the Front DRW
Panels onto the assembled
drawers and secure with 2 Short
Screws (G) on either side.
STEP 15
Finally place the Drawers
underneath the bed. Line them
up with the blocks on the Lower
Front Rail (U) and carefully slide
them into place. The assembly is
now complete.
G
G
G
U
CARE & MAINTENANCE
as they may cause damage to the finish. Periodic checks are recommended to make sure that all bolts, screws and nuts are securely tightened.
:
The touch of a soft cloth is all the maintenance the finish will ever need. Please do not use harsh or abrasive cleaners for polishing,
Keep these instructions for future reference.
! IMPORTANT !
To help prevent serious or fatal injuries from entrapment or falls:
Follow the information on the warnings appearing on the upper bunk end structure and
on the carton. Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent
the likelihood of entrapment or falls.
Use only mattress which is 75 inches long and 39 inches wide on upper bunk; And 75
inches long and 54 inches wide on lower bunk. Ensure thickness of mattress and
foundation combined does not exceed 6 inches and that mattress surface is at least 5
inches (127 mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Prohibit more than one person on the upper bunk at all times.
Periodically check and ensure that the guardrails, ladder, and other components are in
their proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts.
Contact the manufacturer or dealer for replacement
parts.
Use of a night light may provide added safety precaution for a child using the upper
bunk.
Always use guardrails on both sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and wall.
The use of water or sleep flotation mattresses is prohibited.
STRANGULATON HAZARD - Never attach or hang items to any part of the bunk bed that are
not designed for use with the bed; for example: but not limited to - hooks, belts, and jump ropes.
Loading...