HARDWARE IDENTIFICATION
Z-B2 (BOX 2) - Hardware pack
LOWER BED END
1.1 Align and fasten front (E) and back lower (F) side rail to left (C) and right lower (D) bed end
using long bolt (1) and barrel nut (2). DO NOT FULLY TIGHTEN AT THIS STEP.
1.2 Align and fasten wood cleat (10) to front lower side rail (E) using short wood screw (8) and tighten
with screw driver (not included).
1.3 Tighten all the bolts from STEP 1.1.
STEP 1
UPPER BED END
STEP 2
Align and fasten front (H) and back upper (G) guard rail to right (B) and left upper (A) bed end using barrel nut (2)
and long bolt (1) and tighten with Allen wrench (5).
3.1 Insert metal pin (7) into the post of lower bed end (C & D).
3.2 Stack upper bunk bed onto lower bunk bed.
3.3 Align and fasten trestle bar (N) to front upper guard rail (H) using short bolt (3) and tighten with Z-Allen wrench (6)
3.4 Align and fasten upper bunk slat set to front (H) and back upper (G) guard rail using short wood screw (8) and tighten
with screw driver (not included).
3.5 Align and fasten lower bunk slat set to front (E) and back lower (F) side rail using short wood screw (8) and tighten
with screw driver (not included).
N
4.1 Align and fasten left (K) and right (L) ladder stile to ladder step (M) using long wood screw (4) and wood
dowel (9) and tighten with Z-Allen wrench (6).
4.2 Align and fasten ladder to front upper guard rail (H) using short bolt (3) and tighten with Z-Allen wrench (6).
Align and fasten drawer side panel (P) to drawer back
panel (Q) using short wood screw (8) and tighten with
screw driver (not included).
Align and slot the drawer bottom panel (R) to
side (P) and back (Q) panel.
Insert drawer front panel (O) to bottom panel.
Align and fasten drawer front panel (O) to side
panel (P) using short wood screw (8) and tighten with
screw driver (not included).
SAFETY WARNING
Our bunk beds have been tested by an independent laboratory
and are certified to be in compliance with ASTMF-1427, “Standard Consumer Safety Specification for Bunk
Beds” and U.S. Government specifications 16 Code of Federal Regulations
Follow the information on the warning attached to the upper bunk end structure and on the carton. Do
1
not remove this label.
Always use the recommended size mattress or mattress support or both to help prevent the likelihood of
2
entrapment or falls.
3 Surface of mattress must be at least five inches (127mm) below the upper edge of guardrails.
4 Do not allow children less than six years of age to use the upper bunk.
5 Prohibit more than one person on upper bunk.
Periodically check and ensure that the guardrail, ladder and other components are in their proper
6
position, free from damage, and that all connectors are tight.
7 Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8 Always use the ladder for entering and leaving the upper bunk.
9 Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10 Use of a night light may provide added safety precaution for a child using upper bunk.
If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be
11
placed against the wall to prevent entrapment between the bed and the wall. (This applies only to bunk
beds without two full-length guardrails.)
12 Always use guardrails or both long sides of the upper bunk.
13
The use of water or sleep flotation mattress is prohibited.
14 Keep these instructions for future reference.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for
15
example, but not limited to hooks, belts, and jump ropes.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress which is 37 ½” – 38 ½” in width and 75” in length. The total thickness of
mattress and foundation (slat kit, bunk board, etc.) combined must not exceed 6”
Note: There must be at least 5” from mattress sleeping surface to top edge of guardrail.
REPLACEMENT PARTS:
Replacement parts, including additional guardrails may be obtained
PAGE 7 OF 8
Loading...