TWIN/TWIN BUNKBED
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 6
SHORT GUARDRAIL
ASSEMBLY INSTRUCTIONS
!
ROLL SLAT
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instruction in the same sequence as numbered to assure fast & easy assembly.
Warning!
1. Don't attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
2. This product is for home use only and not intended for commercial establishment
PARTS IDENTIFICATION
A
B
C
D
E
F
G
RIGHT UPPER BED
1PC
END
LEFT UPPER BED END 1PC
LOWER BED END 2PCS
UPPER BACK BED
1PC
RAIL
UPPER FRONT BED
1PC
RAIL
LOWER FRONT BED
1PC
RAIL
LOWER BACK BED
1PC
RAIL
H
I
J
K
L
M
N
LONG GUARDRAIL 2PCS
2PCS
RIGHT LADDER STILE 1PC
LEFT LADDER STILE 1PC
LADDER STEP 4PCS
2SETS
(13PCS)
FLAT TRESTLE BAR 3PCS
1
2
3
4
LONG BOLT 22PCS
BARREL NUT 22PCS
WOOD DOWEL 30PCS
SHORT BOLT 14PCS
HARDWARE IDENTIFICATION
5
6
7
8
9
PAGE 2 OF 6
ALLEN CAP SCREW 8PCS
METAL DOWEL 4PCS
ALLEN WRENCH 1PC
MEDIUM BOLT 4PCS
WOOD SCREW 16PCS
STEP 1 STEP 2
back bed rail.
using Allen cap screw and tighten with Allen wrench.
ASSEMBLY INSTRUCTIONS
1.1 Insert wood dowel to both ends of lower front and
1.2 Align and fasten lower front and back bed rail to
lower bed end using long bolt and barrel nut .Tighten
with Allen wrench.
2.1 Insert wood dowel to both ends of long guardrail and
upper front and back bed rail.
2.2 Align and fasten upper front and back bed rail to left
and right upper bed end using long bolt and barrel nut. DO
NOT TIGHTEN AT THIS STEP.
2.3 Align and fasten long guardrail to left and right upper
bed end using long bolt and barrel nut.THEN TIGHTEN
ALL THE BOLTS AT STEP 2.1 AND STEP 2.3 WITH
ALLEN WRENCH.
STEP 3 STEP 4
Insert metal dowel to the top of lower bed ends.Then
align and place the upper bed ends onto the metal dowel.
4.1 Insert wood dowel to both ends of ladder step.
4.2Align and fasten ladder step to left and right ladder stile
PAGE 3 OF 6
STEP 5 STEP 6
Allen wrench.Then align and fasten another flat trestle bar
Align and fasten ladder to the upper front bed rail and
lower front bed rail using medium bolt and tighten with
Allen wrench.
6.1 Insert wood dowel to both end of short guard rail.
6.2 Align and fasten short guard rail to left upper bed end
using long bolt and barrel nut and tighten with Allen
wrench.
6.3Align and fasten left ladder stile to short guard rail using
short bolt and tighten with Allen wrench.
ASSEMBLY INSTRUCTIONS
STEP 7 STEP 8
7.1 Align and fasten flat trestle bar to long guardrail and
upper back bed rail using short bolt and tighten with
to another short guardrail and upper front bed rail using
short bolt and tighten with Allen wrench.
7.2 Align and fasten roll slat to lower and upper bed rail
using wood screw and tighten with screw driver (NOT
INCLUDED).
Complete
PAGE 4 OF 6
SAFETY WARNING
9
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Follow the information on the warning attached to the upper bunk end structure and on the carton. Do
1
not remove this label.
Always use the recommended size mattress or mattress support or both to help prevent the likelihood of
2
entrapment or falls.
3 Surface of mattress must be at least five inches (127mm) below the upper edge of guardrails.
4 Do not allow children less than six years of age to use the upper bunk.
5 Prohibit more than one person on upper bunk.
Periodically check and ensure that the guardrail, ladder and other components are in their proper
6
position, free from damage, and that all connectors are tight.
7 Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8 Always use the ladder for entering and leaving the upper bunk.
9 Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10 Use of a night light may provide added safety precaution for a child using upper bunk.
If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be
11
placed against the wall to prevent entrapment between the bed and the wall. (This applies only to bunk
beds without two full-length guardrails.)
12 Always use guardrails or both long sides of the upper bunk.
13 The use of water or sleep flotation mattress is prohibited.
14 Keep these instructions for future reference.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for
15
example, but not limited to hooks, belts, and jump ropes.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress which is 37 ½” – 38 ½” in width and 74” – 75” in length. The total thickness of
mattress and foundation (slat kit, bunk board, etc.) combined must not exceed 6”
Note: There must be at least 5” from mattress sleeping surface to top edge of guardrail.
REPLACEMENT PARTS:
PAGE 5 OF 6
1. When using beds as bunk beds, the ladder MUST be securely
cannot use the ladder in any manner.
3. DO NOT use, nor permit children to use, the ladder in any
manner whatsoever, other than to access the top unit when
used as bunk beds, and only if the ladder is securely attached
to the top bunk rail, as set forth in the instructions.
4. Any misuse or unauthorized use of the ladder could result in
serious or fatal injury.
attached to the upper bunk rail at all times.
2. When using the beds as two (2) separate floor-standing beds,
the ladder MUST be stored in a separate location where children
PAGE 6 OF 6
Loading...