ISA SLIM GD 100 RV TN, SLIM GD 130 RV TN, SLIM GD 190 RV TN User manual
SLIM GD
EN
100 RV TN
130 RV TN
190 RV TN
ISA S.r.l.
Via del Lavoro, 5
06083 Bastia Umbra - Perugia - Italy
Tel. +39 075 80171 - Fax +39 075 8000900
www.isaitaly.com
SLIM GD
USE AND MAINTENANCE MANUAL
428000454137
WALL-SITE DISPLAY
1
1. MANUFACTURER 4
2. WARRANTY TERMS AND CONDITIONS 4
3. EQUIPMENT IDENTIFICATION 5
4. USE 6
4.1 COMPOSITION 6
5. NOTES / IMPORTANT NOTES 7
6. SAFETY 9
6.1 SAFETY DEVICES PRESENT 9
6.2 FIXED PROTECTIONS 9
6.3 ISOLATING THE ELECTRIC POWER SUPPLY 9
6.4 RESIDUAL RISKS 9
6.5 RISKS OF CONTACT WITH LIVE PARTS 9
6.6 FIRE 10
6.7 EXPLOSIVE ATMOSPHERE 10
6.8 SLIPPING 10
6.9 TRIPPING 10
6.10 CIRCUIT FAULTS 10
6.11 WARNING SIGNS (if any) 10
6.12 RISKS OF EXPLOSION 10
6.13 FALLING OBJECTS 10
6.14 COOLING 11
6.15 FOODSTUFFS SAFETY
(PACKAGED PRODUCTS) 11
6.16 REFRIGERANT 11
7. DISPOSAL OF WASTE MATERIAL 12
8. INSTALLATION 13
8.1 STORAGE AND UNPACKING 13
8.2 INSTALLATION - POSITIONING - ENVIRONMENTAL CONDITIONS 13
8.3 ELECTRIC CONNECTION 13
9. MAINTENANCE 14
10. FAULTS - TECHNICAL AFTER-SALES ASSISTANCE 15
10.1 ALARMS LIST
(WHERE PRESENT) 16
11. TECHNICAL SPECIFICATIONS 17
11.1 INSTALLATION 18
11.2 LOAD LIMITS 18
11.3 POSITIONING / LEVELLING 19
11.4 SHELVES 20
11.4.1 MAX LOAD ON SHELVES 20
11.5 LIGHTING 21
12. CONTROL PANEL 22
12.1 USER INTERFACE 23
13. CLEANING 25
14. PROLONGED APPLIANCE SWITCH-OFF 27
WALL-SITE DISPLAY
SLIM GD
USE AND MAINTENANCE MANUAL
428000454
137
2
EN
Attachment 1 DECLARATION OF CONFORMITY 28
Attachment 2 WIRING DIAGRAM - 412100637200 29
Attachment 3 WIRING DIAGRAM - 412100719000 30
Attachment 4 WIRING DIAGRAM - 412100629000 31
The manual contains symbols to attract the reader’s attention and highlight particularly
important aspects. The table below illustrates the meaning of the various symbols used.
Read the instructions manual
Danger: Live electrical parts
Attention / Danger
Information
Visual observation
Condensing unit on board
Use of protective clothing
Requests for maintenance or operations must
be carried out by qualifi ed staff or technical
after-sales centres.
Important information
Operations that must be performed by two
persons.
Notes / Important notes
Remote condensing unit
EN
SLIM GD
USE AND MAINTENANCE MANUAL
428000454137
3
WALL-SITE DISPLAY
1. MANUFACTURER
ISA S.r.l.
Via del Lavoro, 5
06083 - Bastia Umbra - Perugia - Italy
Tel. +39 075 80171
Fax +39 075 8000900
www.isaitaly.com
2. WARRANTY TERMS AND CONDITIONS
The seller's warranty on the equipment is valid for 12 (TWELVE) months from the date of delivery.
The warranty includes repairs or replacements of any faulty parts due to manufacturing processes or
installation after written communication has been received, stating the appliance serial number and date
of installation.
Not included in the warranty:
• all defects caused by incorrect use of the appliance
• all defects caused by incorrect electrical connection
• all defects caused by normal wear (for instance compressor failure and fl uorescent lamp malfunctioning
that is not due to manufacturing defects)
• calls for installation, technical instructions, adjustments and cleaning the condenser
If the seller's technical staff detect any tampering, unauthorised repairs or inappropriate use of appliance
the warranty will be invalidated.
Shipment of components covered by the warranty is freight collect only.
Any damage to the appliance detected at the time of delivery due to transport must be reported on the
same shipping note to claim compensation from the carrier.
The seller cannot be held liable in the event of damage to the preserved product due to appliance failure
WALL-SITE DISPLAY
SLIM GD
USE AND MAINTENANCE MANUAL
428000454
137
4
EN
3. EQUIPMENT IDENTIFICATION
• Find the label affi xed on the machine to read the technical data.
• Check the machine model and the power supply voltage before you perform
any operation.
• If you uncover mismatches, contact the manufacturer or the company that
supplied the machine immediately.
1 Symbols of Compliance
2 Manufacturer's address
3 Production Order
4 Type
5 Model Name
6 Article
7 Serial Number
8 Production Date
9 - 10 Power supply Voltage and Frequency
11 Gross Capacity
12 Absorption at Rated Capacity
13 Absorption during Defrosting
14 Absorption of Heating Elements
15 Lamp Power
16 Fuse Value
17 Climate Class
18 Number of Motors
19 Type of Coolant
20 Amount of Coolant
21 Safety Class
22 - 23 Customer order
24 RAEE Mark
EN
SLIM GD
USE AND MAINTENANCE MANUAL
428000454137
5
WALL-SITE DISPLAY
4. USE
This appliance is exclusively intended to:
DISPLAY AND SELL BEVERAGES
The manufacturer is not liable for injury to persons or damage to property or the appliance itself
caused by the displaying of products other than those described above.
Never use electric devices inside this appliance.
Do not use mechanical or other means to accelerate the defrosting process, other than recommended
by the manufacturer.
Keep the air vents in the casing of the appliance or in the structure built into the wall free of
obstructions.
THE APPLIANCE IS INTENDED FOR PROFESSIONAL USE.
USES NOT ALLOWED:
• Food preservation.
• Displaying and/or preserving non-food products (chemicals, pharmaceuticals, etc...).
4.1 COMPOSITION
The appliance is made up from a unique cabinet, onto which all devices necessary to make it a professional
and effi cient product for its declared use, are installed.
The appliance is made up from:
• Cooling system at Ventilated Refrigeration (RV)
• Condensing unit on board (UCB) extractable.
• Electric system.
• Electronic controller.
• Insulated monolithic structure in ecological polyurethane.
• Height-adjustable feet for stabilisation of the fl oor.
• Shelves for displaying food products height-adjustable.
• Lighting LED.
• Front closure with double glass (GD).
WALL-SITE DISPLAY
SLIM GD
USE AND MAINTENANCE MANUAL
428000454
137
6
EN
5. NOTES / IMPORTANT NOTES
The content of this manual is of technical nature and is owned by ISA.
It is forbidden to reproduce, circulate or modify all or part of its content without written consent. Any
infringement will be legally pursued.
The manual and the conformity certifi cate are an integral part of the equipment and should always
accompany the product in the event of a transfer to a new location or to a new owner . The user is responsible
for the integrity of these documents, for their consultation and during the whole life cycle of the equipment
itself. Keep this manual in a safe place. It should be available for consultation near the equipment at all
times. If lost or destroyed, you can request a copy of the manual from ISA by specifying the exact model,
serial number and year of manufacture. The manual refl ects the manufacturing technology at the time of
supply . The manufacturer reserves the right to modify its products in an y wa y it deems necessary, with no
obligation to update manuals and machines relating to previous manufacturing batches.
This equipment is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities or by persons lacking the necessary experience and knowledge, unless they are
supervised by a person responsible for their safety who has instructed them on how to use the equipment.
Children should be supervised to ensure that they do not play with the equipment. Always refer to this
manual before going ahead with any operation. Before doing any type of work, disconnect the equipment
from the power supply. Any work on electric and electronic parts or cooling system components should
only be carried out by trained personnel in compliance with current laws.
The Manufacturer cannot be held liable for any injury to persons or animals, or damage to the product
itself in the event of:
• Improper use of the equipment or use of the appliance by unqualifi ed or unauthorised personnel
• Failure to comply with current legislation
• Incorrect installation and/or power supply faults
• Failure to observe the instructions contained in this manual
• Failure to follow the maintenance programme
• Unauthorised modifi cations
• Installation of non-original spare parts in the equipment
• Installation and use of the equipment for purposes other than those for which the appliance was
designed and sold
• Tampering with or damage to the power supply cable
Liability for applying the safety instructions contained in this manual is held by the technical personnel
responsible for the intended use of the equipment, who should ensure that authorised personnel:
• Are qualifi ed to carry out the requested activity
• Are aware of, and carefully comply with, the instructions contained in this document
• Are aware of, and apply, the general safety standards applicable to the equipment
The buyer is responsible for training personnel using the appliance on the risks, safety devices and
general health and safety rules required by the laws of the country where the appliance is installed.
Users/operators should be aware of the position of all the controls and how they work, as well as of the
features of the appliance.
They should also read this manual in its entirely.
Maintenance work should be conducted by qualifi ed personnel after the appliance has been prepared
adequately.
Danger
Unauthorised tampering or replacement of one or more parts of the appliance, use of accessories
that modify the use of the same and use of spare parts different to those recommended, can become
the cause of injury.
Danger
Any work conducted on the on the appliance must involve disconnection from the power socket and
in any case, none of the protective elements (grid, casing) should be removed by non-qualifi ed staff.
The appliance should not be operated when these protective elements have been removed.
EN
SLIM GD
USE AND MAINTENANCE MANUAL
428000454137
7
WALL-SITE DISPLAY
STAFF TRAINING
The buyer is responsible for ensuring personnel who will use the appliance and maintenance technical
staff are instructed and trained adequately.
The manufacturer is available for advice, clarifi cations, etc. so that the operator and technical staff can
use the appliance correctly.
T o ensure the oper ator's safety, appliance devices should be kept in constant working order. This manual
is intended to illustrate the use and maintenance of the appliance. The operator has a responsibility and
duty to carefully observe the instructions contained within it.
Failure to comply with safety standards may result in injury to personnel and damage to the equipment
components and control unit. The user can contact the dealer to request additional information not
contained in this document, or suggest improvements, at any time.
Before the product is delivered to the customer, it is essential that a trained technical member of
staff checks that the appliance is operating correctly in order to achieve maximum performance.
INTRODUCTION
ISA employs materials of the best quality and as they enter the company, we constantly monitor their
storage and the use as part of the manufacturing process to prevent damage, deterioration and failure.
All manufacturing elements are designed and manufactured in order to guarantee reliability and high safety
standards. All appliances are subjected to a strict testing procedure before delivery . However, please bear
in mind that product performance over time depends on correct use and adequate maintenance. This
manual contains the necessary instructions to maintain the appliance's initial appearance and functions
over time.
Note
In order not to compromise functionality and safety of the appliance, the particularly complex
installation and maintenance activities are not documented in this manual and are performed by
specialised technicians.
The Use and Maintenance manual contains the necessary information for understanding how the
appliance works and how to use it properly, namely: the technical description of the various operational
units, equipment and safety systems, operations, how to use the instruments and the interpretation of
any diagnostics reports, main procedures and information relating to routine maintenance. For correct
use of the appliance, the working environment should comply with current health and safety standards.
The safety requirements, indications, standards and notes illustrated in the various chapters of the
manual are aimed at establishing a code of conduct and a series of obligations to be observed when
performing the various activities, in order to create safe conditions for personnel, the equipment and
the surrounding environment. The safety standards reported in this document are intended for trained,
authorised personnel responsible for:
• Transport
• Installation
• Operation
• Management
• Maintenance
• Cleaning
• Putting out of order
• Disposal
Attention
Reading this manual, albeit in full, is no substitute for adequate user experience. therefore it should
only be considered a useful reminder of the technical features and the main operations to perform.
Warning
The installers and users must read and understand the instructions contained
herein before any operation on the appliance.
WALL-SITE DISPLAY
SLIM GD
USE AND MAINTENANCE MANUAL
428000454
137
8
EN
6. SAFETY
The appliance is equipped with safety devices.
6.1 SAFETY DEVICES PRESENT
Devices whose operation prevents the occurrence of risk situations in operating conditions (e.g. fuses,
pressure switches, protections, magnet circuit breakers, etc.).
6.2 FIXED PROTECTIONS
Fixed protective devices consist of fi xed perimeter shields, which are used to prevent external parts
from entering the equipment.
Danger
It is prohibited to re-start the appliance following maintenance without having correctly restores the
panels.
Visual Check
You should check the integrity of fi xed panels and corresponding fi xings to the frame, focussing in
particular on the protective panels.
6.3 ISOLATING THE ELECTRIC POWER SUPPLY
Before conducting any maintenance work on the equipment or part of it, it is necessary to section the
power supply that powers it.
Danger
In the event of maintenance operations in which the operator cannot prevent accidental closure of
the circuit by others, to totally disconnect the appliance from the mains electricity.
6.4 RESIDUAL RISKS
During design the manufacturer examined all the areas or parts at risk. Therefore, all necessary
precautions have been taken to prevent risks to persons and damage to the appliance.
Attention
Periodically check that all safety devices are operating correctly.
Do not remove the fi xed guards.
Do not introduce objects or tools into the work area.
Although the appliance is fi tted with the safety devices prepared, there are still some risks that
cannot be eliminated, but reduced via corrective actions by the fi nal integrator and correct operational
procedures.
6.5 RISKS OF CONTACT WITH LIVE PARTS
Risk of breaking or damaging the electrical components of the appliance, with a possible reduction in
safety levels, following a short circuit.
Before connecting the electricity supply, make sure there is no ongoing maintenance work.
Attention
Before making the connection, check that the d.c. current in the installation point does not exceed
that indicated on the protections switches present in the electric control board. If this is not the case,
the user must envision the relevant limiting devices.
It is strictly forbidden to conduct any electrical modifi cation, in order to prevent additional unforeseen
hazards and risks.
EN
SLIM GD
USE AND MAINTENANCE MANUAL
428000454137
9
WALL-SITE DISPLAY
6.6 FIRE
Danger
In the event of a fi re, immediately disconnect the master switch from the main power supply line.
6.7 EXPLOSIVE ATMOSPHERE
The equipment must not be located in an area classifi ed as an explosion risk according to 1999/92/EC
such as:
Zone 0
An area in which there is a permanent, long-lasting or frequently explosive atmosphere made up of a
mixture of air and fl ammable substances in the form of gases, fumes or steam.
Zone 1
An area in which the formation of an explosive atmosphere, made up of a mixture of air and fl ammable
substances in the form of gases, fumes or steam is occasionally probable during normal activities.
Zone 20
An area in which there is a permanent, long-lasting or frequently explosive atmosphere in the form of
clouds of combustible dust in the air.
Zone 21
An area in which the formation of an explosive atmosphere in the form of clouds of combustible dust is
occasionally probable during normal activities.
6.8 SLIPPING
Any leaks in the areas surrounding the appliance may cause personnel to slip.
Check that there are no leaks and keep these areas clean at all times.
6.9 TRIPPING
Generally untidy deposits of material may constitute a tripping hazard and a total or partial obstruction
of emergency exit routes.
Ensure that operating and transit areas and emergency exit routes are free from obstacles in
compliance with current legislation.
6.10 CIRCUIT FAULTS
Owing to potential faults, safety circuits may become less effective, which results in lower safety levels.
You should check the operational condition of the appliance devices regularly.
6.11 WARNING SIGNS (IF ANY)
The appliance is fi tted with warning danger, warning and obligation signs defi ned in agreement with the
Standard relative to the graphical signs to be used on plants.
The signs are located in clearly visible positions.
Attention
The warning plates present on the appliance must not be removed.
The user is responsible for replacing warning signs that, owing to wear, become unreadable.
6.12 RISKS OF EXPLOSION
Do not store products that contain combustible gaseous propellants and explosive substances inside
the appliance.
6.13 FALLING OBJECTS
Positioning of the cabinet display parts (i.e. counters, rods and hooks), as also product arrangement
inside the cabinet can be the source of potential hazards if not properly performed.
Follow the positioning instructions described in this Manual before you place products inside the
cabinet, check that the counters are properly fastened, as also the hooks, etc. Do not exceed the
maximum load limit. Do not tilt the shelves. Do not place any goods and in general, do not load the
tank sliding element closing devices with any load, while open or closed.
Do not place any goods and in general, do not load the tank sliding element closing devices
with any load, while open or closed.
WALL-SITE DISPLAY
SLIM GD
USE AND MAINTENANCE MANUAL
428000454
137
10
EN
Loading...