Ironton 46182, 46180, 46179, 46178 Owner's Manual

1/2IN. SPADE HANDLE DRILL

OWNER’S MANUAL

WARNING:

Read carefully and understand all ASSEMBLY AND OPERATION
INSTRUCTIONS before operating. Failure to follow the safety rules and other

basic safety precautions may result in serious personal injury.

Item# 46182

Page of 15

2

Thank you very much for choosing an IRONTON product! For future reference, please complete

the owner’s record below:

Model: _______________ Purchase Date: _______________

Save the receipt, warranty and these instructions. It is important that you read the entire manual

to become familiar with this product before you begin using it.

This machine is designed for certain applications only. The distributor cannot be responsible for
issues arising from modification. We strongly recommend this machine not be modified and/or
used for any application other than that for which it was designed. If you have any questions
relative to a particular application, DO NOT use the machine until you have first contacted the
distributor to determine if it can or should be performed on the product.

For technical questions please call 1-800-222-5381.

INTENDED USE

This product is for driving screws and drilling holes in wood and metal. This product is intended
for consumer use only.

SPECIFICATIONS

• Item#: -------------------------- 46182

• Rated Power: ---------------- 120V AC, 60 Hz, 10.0 Amp

• No-Load Speed: ------------ 1050 RPM, Reversible

• Chuck Size: ------------------ 1/2” (13 mm)

• Cord Length: ----------------- 6.5 ft

Includes: Drill, Auxiliary Handle, Rear Handle and Chuck Key

GENERAL SAFETY RULES

WARNING: Read and understand all instructions. Failure to follow all instructions

listed below may result in serious injury.

CAUTION: Do not allow persons to operate or assemble this saw until they have

read this manual and have developed a thorough understanding of how the saw works.

WARNING: The warnings, cautions, and instructions discussed in this instruction

manual cannot cover all possible conditions or situations that could occur. It must be

understood by the operator that common sense and caution are factors that cannot be built

into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS

WORK AREA SAFETY:

• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

• Inspect work area for hazards before operating tool.

Page of 15

3

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while operating a power tool. Distractions can

cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any way. Double insulated

tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a

polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still

does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in

any way. Double insulation eliminates the need for the three wire grounded power cord and

grounded power supply system.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is grounded.

• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving parts. Damaged cords increase the risk of

electric shock.

• When operating a power tool outside, use an extension cord suitable for outdoor use.

These cords are rated for outdoor use and reduce the risk of electric shock.

• Do not use AC only rated tools with a DC power supply. While the tool may appear to work,

the electrical components of the AC rated tool are likely to fail and create a hazard to the

operator.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of

inattention while operating power tools may result in serious personal injury.

• Not for use by children or people with reduced mental capacity.

• Use safety equipment. Always wear eye protection. Safety equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection for appropriate conditions will reduce

personal injuries.

• Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents

may cover moving parts and should be avoided.

• Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying

power tool with your finger on the switch or plugging in power tools that have the switch on

invites accidents.

Page of 15

4

• Remove any adjusting keys or wrenches before turning the power tool on. A wrench or key

that is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Maintain proper footing and balance at all times. Loss of balance can cause

an injury in an unexpected situation.

• If devices are provided for connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of these devices can reduce dust related hazards.

• Do not use an unstable support. Stable footing on a solid surface enables better control of the

tool in unexpected situations.

• Keep tool handles dry, clean and free from oil and grease. Slippery handles cannot safely

control the tool.

TOOL USE AND CARE

• Secure the work piece. Use clamp or other practical way to hold the work piece to a stable

platform. Holding the work piece by hand or against your body is unstable and may lead to loss

of control.

• Do not force the power tool. The tool will perform the job better and safer at the feed rate for

which it is designed. Forcing the tool could possibly damage the tool and may result in personal

injury.

• Use the correct power tool for the job. Don’t force the tool or attachment to do a job for

which it is not designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with

the switch is dangerous and must be repaired or replaced by an authorized service center.

• Turn power tool off, and disconnect the plug from the power source and/or battery pack from

the power tool before making any adjustments, changing the accessories, or storing the tools.

Such preventive safety measures reduce the risk of an accidental start up which may cause

personal injury.

• Store idle tool out of reach of children and other inexperienced persons. It is dangerous in

the hand of untrained users.

• Maintain power tools with care. Check for proper alignment and binding of moving parts,

component breaks, and any other conditions that may affect the tool’s operation. A guard or any

other part that is damaged must be properly repaired or replaced by an authorized service center

to avoid risk of personal injury.

• Use recommended accessories. Using accessories and attachments not recommended by

the manufacturer or intended for use on this type tool may cause damage to the tool or result in

personal injury to the user. Consult the operator’s manual for recommended accessories.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Page of 15

5

• Feed the work piece in the correct direction and speed. Feed the work piece into a blade,

cutter, or abrasive surface against the direction of the cutting tool’s direction of rotation only.

Incorrectly feeding the work piece in the same direction may cause the work piece to be thrown

out at high speed.

• Never leave the tool running unattended, turn the power off. Do not leave the tool until it

comes to a complete stop.

• Never start the power tool when any rotating component is in contact with the work

piece.

WARNING: USE OF THIS TOOL CAN GENERATE AND DISBURSE DUST OR

OTHER AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST AND

ASBESTOS. Direct particles away from face and body. Always operate tool in a

well-ventilated area and provide for proper dust removal. Use dust collection system

wherever possible. Exposure to the dust may cause serious and permanent respiratory or

other injury, including silicosis (a serious lung disease), cancer, and death. Avoid

breathing the dust, and avoid prolonged contact with the dust. Allowing dust to get into your

mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use

properly fitting NIOSH/OSHA approved respiratory protection appropriate for dust exposure,

and wash exposed areas with soap and water.

SERVICE

• Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

• Service your power tool periodically. When cleaning a tool, be careful not to disassemble

any portion of the tool since internal wires may be misplaced or pinched.

WARNING: Read and understand all warnings, cautions and operating instructions

before using this equipment. Failure to follow all instructions listed below may result in

electric shock, fire and/or serious personal injury.

EXTENSION CORDS

Double insulated tools can use either a two or three wire extension cord. As the distance from the

power supply outlet increases, you must use a heavier gauge extension cord. Using extension cords

with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible

tool damage. Refer to the table shown below to determine the required minimum wire size.

The smaller the gauge number of the wire, the greater the capacity of the cord. For example: a

14-gauge cord can carry a higher current than a 16-gauge cord. When using more than one extension

cord to make up the total length, be sure each cord contains at least the minimum wire size required.

If you are using one extension cord for more than one tool, add the nameplate amperes and use the

sum to determine the required minimum wire size.