Ironton 39109 Owner's Manual

1 4 I N C H A B R A S I V E C H O P S A W

OWNER’S MANUAL

WARNING:

Read carefully and understand all MACHINE ADJUSTMENT AND OPERATION
INSTRUCTIONS before operating. Failure to follow the safety rules and other basic

safety precautions may result in serious personal injury.

Item # 39109

Page of 12

2

Thank you very much for choosing an Ironton product! For future reference, please complete

the owner’s record below:

Model: _______________ Purchase Date: _______________

Save the receipt, warranty and these instructions. It is important that you read the entire manual

to become familiar with this product before you begin using it.

This machine is designed for certain applications only. The distributor cannot be responsible for
issues arising from modification. We strongly recommend this machine not be modified and/or
used for any application other than that for which it was designed. If you have any questions
relative to a particular application, DO NOT use the machine until you have first contacted the
distributor to determine if it can or should be performed on the product.

For technical questions please call 1-800-222-5381.

INTENDED USE

This 14-inch chop saw has a 15 Amp, 3,800 RPM motor that’s ideal for cutting steel, and concrete.

It is not recommended for cutting wood or plastic. Do not attempt to install a toothed blade on

the tool.

TECHNICAL SPECIFICATIONS

Item

Description

Voltage

120V AC power

Disc diameter:

14’’

Power input

15A

Speed (no load)

3800 RPM

Max. Cutting Capacity - Round

4.7”

Max. Cutting Capacity - Square

4 5/8“. X 4 5/8”

Arbor Size

1’’

Hearing protection should be worn when using chop saw.

GENERAL SAFETY RULES

1) Work area

a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks, which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

Page of 12

3

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personal injury

b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce

personal injuries

c) Avoid accidental starting. Ensure the switch is in the off-position before plugging in.

Carrying power tools with your finger on the switch or plugging in power tools that have the switch

on invite accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving

parts.

g) If devices are available in your shop for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of these devices can

reduce dust related hazards.

4) Power tool use and care

a) Secure work. Use a clamp, vise or other practical means to hold your work securely, freeing

both hands to control the tool.

b) Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed

c) Do not use the power tool If the switch does not turn It on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

d) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of starting the power tool accidentally,

e) Store idle power tools out of reach of children and do not allow persons unfamiliar with

the power tool or these Instructions to operate the power tool. Power tools are dangerous in

the hands of untrained users.

f) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tools operation. If

damaged, have the power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

g) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

h) Use the power tool, accessories and tool bits in accordance with these

instructions and in the manner Intended for the particular type of power tool, taking

Page of 12

4

Into account the working conditions and the work to be performed. Use of the power

tool for operations different from those intended could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualified repair person using only Identical

replacement parts. This will ensure that the safety of the power tool is maintained.

WARNING: RECOMMENDED FOR USE WITH A

GFCI WITH A RATED RESIDUAL CURRENT OF 30 mA OR LESS.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush

or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which

in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory's

rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by he work piece. the edge of the

wheel that is entering into the pinch point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may jump either toward or away from the operator, depending on

direction of the wheel's movement at the point of pinching. Abrasive wheels may also break under

these conditions.

Kickback is the result of power tool misuse and/or incorrect operating procedures or

conditions and can be avoided by taking proper precautions as given below.

a) Maintain a firm grip on the power tool and position your body and arm to allow you to

resist kickback forces. Always use auxiliary handle, if provided, for maximum control over

kickback or torque reaction during start-up.

The operator can control torque reactions or kickback forces, if proper precautions are

taken.

b) Never place your hand near the rotating accessory

Accessory may kickback over your hand.

c) Do not position your body in the area where power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp edges etc. Avoid bouncing and

snagging the accessory.

Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and

cause loss of control or kickback

e) Do not attach a Saw chain woodcarving blade or toothed saw blade.

Such blades create frequent kickback and loss of control

SAVE THESE INSTRUCTIONS