Ironmaster Cable Tower Attachment
Assembly and Use Instructions
The Cable Tower Attachment is designed to connect to the Ironmaster Super Bench to
allow upper and lower pulley cable work. It has a unique weight carriage that allows
the use of the Ironmaster Quick-Lock Dumbbells to be the weight source or it will also
work with Standard or Olympic style plates. The system capacity is rated at 250lbs.
The Cable Tower attachment is designed to be used
only in conjunction with the
Ironmaster Super Bench,
and cannot be safely used
as either a stand alone device or with any other product.
Follow all assembly instructions carefully.
Warning:
2
Congratulations on your purchase of this fine Ironmaster product. The following instructions will help you assemble
the unit and provide some details on use as well. The only tools required are two
adjustable wrenches. Unpack all the parts and make sure you have received all the parts as shown on the exploded
view drawing and parts list. If you are missing anything or need anything, please call
Ironmaster right away and we will assist you. 800-533-3339.
Step 1: Assemble FRONT BRACKET #11 and
REAR LOW PULLEY BRACKET #15 to BASE
FRAME #9 using bolts #1, washers #3 and Nuts
#2. Be sure to insert bolts from underside of
BASE FRAME with nuts and washers on top.
Refer to exploded view on page 7 for orientation.
Install forward pulley #15a using Allen head bolt
#15b and Nut #15c. No washer is used. Leave
nut hand tight for now.
Step 2: Assemble FRONT TUBE UPRIGHT #21
and SLIDE RAIL #17 using bolts #4 and washers #3.
Step 3: Assemble BENCH CONNECTOR #10
(chrome plated) to FRONT TUBE UPRIGHT #21
using bolt #4 and washer #3 on top and Bolt #1
and washer #3 on bottom. Be sure to locate hole
for bench pull pin on left hand side as shown.
Note: The connector can be adjusted up or down
to match up to the bench if
necessary. Leave the bolts finger tight until
adjusted as a final step.
1
2
Step 4: Install ROUND TUBE #18 using bolt #5 and
washer #3. Push FOAM PAD SPACERS #14 on first then
the FOAM ROLLER PADS #13. Secure with bolt #7,
dome cap #12 and washer #8 as shown in exploded view.
Note: There are 3 height positions available so you can
select the most comfortable height for the leg hold down.
3
4
Front Bracket
Rear low Pulley Bracket
Slide Rail
Front
tube
upright
Forward
Pulley
Front tube upright
Bench connector
Bench pull pin locator
Round tube
Foam pad spacer
Foam roller pad
3
Step 7: Thread UPPER CABLE #26 over right top
pulley and connect the WEIGHT CARRIAGE #23 with
the SNAP HOOK #22. Set PULLEY #15a over the
cable and fit into the IDLER PULLEY HOUSING #30
with Allen Bolt #15b and Nut #15c. Leave hand tight
for now.
Step 8: Thread LOWER CABLE #27 under left bottom pulley, through the tube hole and screw in the adjustment bolt
into the threaded hole in the BASE FRAME #9. Set PULLEY
#15a under the cable and fit into the IDLER PULLEY HOUSING #30 with Allen Bolt #15b and Nut #15c. Leave hand tight
for now.
Step 5: Install SPRING #16 and WEIGHT CARRIAGE #23 over SLIDE RAIL #17 as shown.
5
6
Spring
Weight Carriage
Step 6: Install pulleys #15a with black Allen bolts #15b and
hex nuts #15c onto TOP PULLEY BRACKET. Leave nuts
hand tight for now. Install TOP PULLEY BRACKET #25 onto
top of slide rail and front tube upright using bolts #1, washers
#3 and nuts #2 as shown.
Pulley
Front tube upright
Slide rail
Top Pulley
Bracket
Slide rail
Lower left
pulley
Upper cable
Idler Pulley
housing
Snap Hook
Install lower left pulley only after cable is
threaded through the
tube hole, as front of
cable will not pass
with pulley in place.
Lower idle arm pulley to
be installed after cable is
threaded around pulley to
allow cable head to pass.
7
8
Weight
Carriage
4
9
Step 10: If you plan to use the Ironmaster Quick-Lock
Dumbbells as the weight source on the carriage, install
the CARRIAGE DUMBBELL ADAPTER #24 using bolt
#6 with the Allen wrench as shown.
Step 9: Adjust the cable tension by screwing in the adjustment
screw to remove the slack in the cable. Lock the posi tion with the
lock nut to the BASE FRAME #9.
Note: It will be necessary to readjust this screw after some use of
the cable system. Adjust as needed. It is recommended to set
some weight on the CARRIAGE #23 to pretension the cable before adjusting.
10a
10b
Be sure to check and tighten all bolts
before use. It will be necessary to
use a wrench to hold the nuts when
tightening the Allen bolts on the
Pulleys.
Carriage Dumbbell
adapter
Adjustment
screw
Step 11: If you
plan to use Olympic style weight
plates on the
weight carriage,
you can install the
2 included OLYMPIC SLEEVE
ADAPTERS #28
as shown. Secure
with the set
screws. Push on
the rubber rings
#29 as bumpers.
11a
11b
Olympic Sleeve
Adapter
Important:
5
The CHAIN #20 may be connected to the cable end to lengthen the
reach from the upper or lower pulley. Take care when routing the pulley cables to be sure they fit completely in the PULLEY grooves. The
SNAP HOOKS #22 are used to connect the cables to the CARRIAGE
#23 and to the exercise handle you select. The system includes the
LAT PULL DOWN HANDLE #19 that can be used for lat pulls, cable
press downs, low rows, cable curls, upright rows, etc. You may use a
variety of cable handles with this system—sold separately.
Optional attachments are available such as the Low Row Footplate, Dockable Curl Support and various cable attachment handles. Please visit
www.ironmaster.com for more details.
6
Warranty Information:
Your Ironmaster attachment has a limited 10 year warranty to the original purchaser. Cables and
padding are covered for two years. Warranty covers repair or replacement for mechanical integrity
when used according to the instructions for normal exercise use. Warranty covers in home use only.
Finish and wear items such as rubber and painted surfaces are not covered. If you need warranty
service, contact Ironmaster for return instructions and additional terms and conditions.
Ironmaster LLC, 21828 87th Ave SE, #E, Woodinville, WA 98072 800-533-3339, 425-408-9040
No. Description Qty Detail
1 Bolt - M10x70 7 Chrome
2 Nut - Nylon insert 10mm 6 Chrome
3 Washer - 10mm 18 Chrome
4 Bolt - M10x20 8 Chrome
5 Bolt - M10x25 1 Chrome
6 Bolt- Allen Head M10x35 2 Black
7 Bolt- Allen Head M8x25 2 Black
8 Washer - M8 2 Chrome
9 Base Frame 1 Powder coated grey
10 Bench Connecter 1 Chrome
11 Front Bracket 1 Powder coated grey
12 Plastic Dome Cap 2 Black cap for foam roller pads
13 Foam Roller Pad 2 Black Neoprene
14 Foam Spacer Pad 2 Black rubber - small
15 Rear Low Pulley Bracket 1 Powder Coated Grey
15a Cable Pulley 7 Black plastic
15b Allen Bolt –M10 7 Black finish
15c Nut-Nylon insert 12mm 7 Chrome
16 Spring 1 Chrome
17 Slide Rail 1 Powder Coated Grey
18 Round Tube - 1" dia. 1 Powder Coated Grey - foam roller pad holder
19 Lat Pull Down Handle 1 Chrome
20 Chain 1 Chrome
21 Front Tube Upright 1 Powder Coated Grey
22 Snap Hook 3 Chrome
23 Weight Carriage 1 Powder Coated Grey with slide bushings
24 Dumbbell Adapter 1 Powder Coated Grey
25 Top Pulley Bracket 1 Powder Coated Grey
26 Front Cable 1 76" long with rubber stop
27 Rear Cable 1 130.5" long with rubber stop
28 Olympic Sleeve Adapter 2 Plastic Black, 2" x 9"
29 Rubber Bumpers 2 Ring for when the Olympic sleeves are used
30 Idler Pulley Housing 1 Powder Coated Grey
PARTS LIST FOR IRONMASTER CABLE TOWER ATTACHMENT
7
Exploded View—Ironmaster Cable Tower
Loading...