Iron-A-Way AE46, AE42, E46, E42, ANE46 Installation Manual
...
Installation
Manual
MODELS:
AE46, AE42, E46, E42, ANE46, ANE42, NE46, NE42
TABLE OF CONTENTS
SWIVEL UNITS (AE46, AE42, ANE46, ANE42)............................pg.3
NON-SWIVEL UNITS (E46, E42, NE46, NE42)...........................pg.11
ELECTRICAL INSTRUCTIONS.....................................................pg.17
Premier Storage Systems
220 W. Jackson St, Morton, IL 61550
1-800-536-9495 or info@ironaway.com
(BOTTOM OF RACEWAY)
Swivel Units
Models: AE46, AE42, ANE46, ANE42
2
1
4
6
3
ELECTRICAL MODELS
(AE46 SHOWN)
3
NON- ELECTRICAL MODELS
6
(ANE46 SHOWN)
1
GET TO KNOW YOUR UNIT
1. CROSS BRACES
- Three braces for 46” units
- Two braces for 42” units
2. ELECTRICAL RACEWAY
(AE46, AE42)
3. SIDE BRACKETS
4. ELECTRICAL CORD COVER
(AE46 only; AE42
features a cord wrap)
5. ELECTRICAL OUTLET
6. HOT IRON REST
(AE46, ANE46)
Tools Needed:
- Stud Finder
- 12-14” Level
- Tape Measure
- Small Flathead
Screwdriver
- Electric Drill
(with 1/4” & 1/8” drill bit)
- 1/4” Nut Driver
(optional)
- Safety Glasses
- Utility Knife
Supplied Parts:
Recessed Mounting:
- Two #10 x 1 1/2” wood screws for top
portion of cabinet
- Two #14 x 2 1/2” Phillips screws for top
side brackets
Surface Mounting:
- Two #14 x 4” wood screws
3
SWIVEL: PRE-INSTALLATION
1. DETERMINE MOUNTING HEIGHT
Using the charts provided, determine
the mounting height above oor (the
distance between the oor and the
bottom of the cabinet). First choose
your desired ironing board height
from the left column, then locate the
corresponding mounting height in the
right column.
AE46 & ANE46
Desired Ironing
Board Height
36”
35”
34”
33”
AE42 & ANE42
Desired Ironing
Board Height
Mounting
Height Above
Floor
29”
28”
27”
26”
Mounting
Height Above
Floor
Desired Ironing
Board Height
36”
35”
34”
33”
25”
24”
23”
22”
2. LOCATE STUDS & UTILITIES
Using a stud nder, locate the wall
studs to be used for mounting.
Locate the existing wiring or other
utilities in the wall to prevent drilling
into/severing a wire and/or other utility
during installation.
Mounting
Height
Above Floor
4 - Swivel Installation
3. ENSURE ADEQUATE SPACE
Refer to the chart provided below to ensure
adequate clearance for ironing. The cabinet
door opens at 180 degrees; allow 16” from side
of cabinet for door to fully open.
1. Distance needed on either side of unit to fully swivel the board
2. Distance from wall to tip of ironing board
3. Distance from wall to board when in full swivel position
4. Standing area clearance (not shown)
The suggested distance from the side of the ironing where the user
typically stands to ensure adequate space for ironing.
AE46
ANE46
7/8
16
7/8
50
7/8
32
” 32
24” 24”
AE42
ANE42
” 14
” 46
5/8
”
7/8
”
7/8
”
Swivel Installation - 5
SWIVEL: RECESSED INSTALLATION
Note: Instructions based on installation between 16” on-center studs.
1. CUT WALL OPENING
Cut an opening into the wall based
on unit dimensions given below.
AE46/ANE46: 14
AE42/ANE42: 14
3/8
” x 59
3/8
” x 51
7/8
1/4
” x 3
x 3
7/8
7/8
”
”
2. ATTACH CLEATS
Attach a 2” x 4” cross support
cleat between the studs so it
is level with the bottom of the
opening. This will give support to
the drywall during installation and
the cabinet once installed in the
wall.
3. PRE-DRILL HOLES
Your unit will be attached to the studs by
screws in the upper and lower sides of
the cabinet.
AE46 & AE42: Remove electrical
raceway before proceeding by
removing the top and bottom screws on
the raceway.
Using a 1/8” drill bit, pre-drill holes into
the sides of the cabinet, 14” from the top
and 2
1/2
” from the back.
14” from top of cabinet
CLEAT
1/2
2
” from back
of cabinet
Example shown with exposed
studs & unit to illustrate mounting.
6 - Swivel Installation
AE46 SHOWN
Loading...