9522A
L-BAND TRANSCEIVER
USER’S GUIDE
43755_user_guide 2/1/05 5:00 PM Page 1
Contents
Export Compliance Information . . . . 1
1 Product Overview . . . . . . . . . . . . . 1
2 Standards Compliance . . . . . . . . . 1
2.1 FCC Compliance . . . . . . . . . . . 1
2.2 CE Compliace . . . . . . . . . . . . . 1
3 Physical Specifications . . . . . . . . . 2
3.1 Environmental . . . . . . . . . . . . . 2
3.2 Dimensions . . . . . . . . . . . . . . . 2
3.3 Interface Connectors . . . . . . . 3
3.3.1 Multi-Interface Connector . . 3
3.3.2 Antenna Connector . . . . . . . 4
3.3.3 SIM Chip Reader . . . . . . . . . 4
3.4 Mounting . . . . . . . . . . . . . . . . . 4
3.5
Connector Sealing in Harsh
Environments
. . . . . . . . . . . . . . 5
4 Electrical Interfaces . . . . . . . . . . . 5
4.1 DC Power Interface . . . . . . . . . 5
4.1.1
DC Power Interface Signal
Specifications
. . . . . . . . . . . . 5
4.1.2
DC Power Input Specifications
5
4.2 Control/Digital Audio
(DPL Bus) Interface . . . . . . . 6
4.2.1 Control/Digital Audio Interface
Signal Descriptions . . . . . . . 6
4.3 RS232 Data Interface . . . . . . . 6
43755_user_guide 2/1/05 5:00 PM Page 2
4.3.1 RS232 Data Signal
Descriptions . . . . . . . . . . . . . 6
4.3.2 Autobaud . . . . . . . . . . . . . . . 6
4.4 Analog Audio Interface . . . . . . 6
4.4.1 Analog Audio Interface Signal
Descriptions.. . . . . . . . . . . . . 6
4.5 SIM Interface . . . . . . . . . . . . . . 6
4.6 RF Interface . . . . . . . . . . . . . . . 7
4.6.1 RF Interface Specifications . 7
4.6.2 Radio Characteristics . . . . . 7
5
Instructions for Safe Installation
. . . 7
5.1 Instructions for the Integrator 7
5.2
Instructions from the Integrator
8
6
Modem Commands and Configuration
8
Warranty. . . . . . . . . . . . . . . . . . . . . . . . 9
1 Coverage. . . . . . . . . . . . . . . . . . . . . 9
2 Conditions. . . . . . . . . . . . . . . . . . . . 9
3 Obtaining Warranty Service . . . . . . 9
4 General Provisions . . . . . . . . . . . . . 10
5 Conditions of Use . . . . . . . . . . . . . . 10
6 State Law . . . . . . . . . . . . . . . . . . . . 11
7 Contact . . . . . . . . . . . . . . . . . . . . . . 11
Declaration of Conformity . . . . . . . . . 12
43755_user_guide 2/1/05 5:00 PM Page 3
Export Compliance Information
This product is controlled by the export laws and regulations of the
United States of America. The U.S. Governement may restrict the
export or re-export of this product to certain individuals and/or destinations. For further information, contact the U.S. Department of
Commerce, Bureau of Industry and Security or visit
www.bis.doc.gov.
1 Product Overview
The 9522A L-Band Transceiver (LBT) is designed to be integrated
into a specific application with other hardware and software to produce a solution designed for a specific application or vertical market.
Some examples of these solutions include a maritime voice telephony terminal or a vehicle tracking solution.
The LBT functionally supports all of Iridium’s voice and data services. Applications can be built to use one or multiple services using
the voice and data interfaces. The 9522A is a functional replacement
to the 9522 “Sebring” LBT. However it should be noted that there are
some differences to the voice interface.
The 9522A is regulatory approved for FCC, Canada, and CE assuming an antenna with a gain of ≤ 3 dBi. This allows the LBT to be integrated into a variety of subscriber products, or retrofitted into existing LBT-based products. These products, when integrated together
will require Regulatory testing to be conducted by the integrator.
The LBT is essentially provided as a ‘black box’ with all interfaces
provided via a DB25 connector. The product provides the core transceiver module and SIM card reader. All other functions and hardware
such as keypad, display, power supply, antenna etc. must be provided by the solution developer. The DB25 provides the following interfaces and connections:
• Analog Audio
• Control / Digital Audio
• RS232
• Power Input
• On / Off
2 Standards Compliance
The 9522A is designed to comply with the standards for Radio
Emissions Compliance, Electromagnetic Compatibility, and AC
Safety in the United States, European Union and Canada.
2.1 FCC Compliance
The 9522A is certified under 47 CFR Part 25 as FCC ID:Q639522A. It
also complies with Part 15 of the FCC Regulations. Operation is subject to the condition that this device does not cause harmful interference. Any changes or modifications, including the use of a non-standard antenna, not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
IMPORTANT: To comply with FCC RF exposure requirements, a minimum separation of 20 cm is required between the antenna and all
persons.
2.2 CE Compliance
This product, when marked with the CE symbol, complies with the
European Community Council Directive for R&TTE, 99/5/EC, provided that the integrator/user adheres to the instructions detailed in this
LBT Interface Specification. This product is in compliance with applicable ETSI standards. Compliance with the requirements of ETSI EN
301 489 requires the use of a shielded digital data interface cable.
1
43755_user_guide 2/1/05 5:00 PM Page 4
3 Physical Specifications
The 9522A LBT is depicted in Figure 1 below.
Figure 1: Top View
3.1 Environmental
The environmental specifications of the 9522A LBT are summarized
in Table 1 below.
Table 1: Environmental Specifications
3.2 Dimensions
The overall dimensions of the 9522A LBT and its weight are summarized in Table 2 below. Dimensioned views of the 9522A LBT are
shown in Figures 2-5 to follow.
Table 2: Mechanical Dimensions
Figure 2: Side View
2
43755_user_guide 2/1/05 5:00 PM Page 5
Parameter Value
Operating Temperature Range -10ºC to + 55ºC
Operating Humidity Range ≤ 75% RH
Storage Temperature Range -40ºC to + 85ºC
Storage Humidity Range ≤ 93% RH
Parameter Value
Length (including antenna connector) 216.1mm (8.51”)
Length (excluding antenna connector) 196.4mm (7.73”)
Width 82.6mm (3.25”)
Depth 39.0mm (1.54”)
Weight (approximate) 659g
Figure 3: Bottom View
Figure 4: Antenna Connector End View
Figure 5: Multi-Interface Connector End View
3.3 Interface Connectors
The 9522A LBT incorporates three interface connectors.
• Multi-Interface Connector (located on the end of the
9522A LBT)
• Antenna Connector (located on the end of the 9522A
LBT; opposite to the multi-interface connector)
• Subscriber Identity Module (SIM) Chip Connector
(located beneath a cover plate atop the 9522A LBT)
3.3.1 Multi-Interface Connector
The multi-interface connector is a 25 pin D-subminiature type that
includes four interfaces.
• DC Power
• Control/Digital Audio (DPL bus)
• RS232 Data
• Analog Audio
The pin out information for this connector is given in Table 3 below.
3
43755_user_guide 2/1/05 5:00 PM Page 6
Table 3: 25-way connector pin-out
3.3.2 Antenna Connector
The 9522A LBT provides a single 50Ω, TNC type antenna connector
both transmit and receive.
3.3.3 SIM Chip Reader
An integrated SIM chip reader is provided on the 9522A LBT. This
connector allows installation of the chip form of the SIM beneath a
cover plate on the 9522A LBT housing.
3.4 Mounting
The 9522A LBT incorporates (6) mounting holes on its bottom surface that can aid in its mounting. See Figure 3 for locations of these
features. It is recommended that a thread-forming screw be used to
mount the 9522A LBT via these features. Particularly, a Textron
Camcar® Taptite® II Thread-Rolling Fastener of M3.5x0.6 thread
type is recommended. This fastener has a 15IP Torx Plus® pan head
and is available in lengths of 6, 8, 12, 16, and 20 mm as part number
3BE-P802-00, 3BE-P803-00, 3BE-P8185-00, 3BE-P804-00, 3BEP8186-00, and 3BE-P8187-00 respectively. Length should be chosen
to ensure that penetration into the 9522A LBT housing does not
exceed 11mm.
If a 6-32 thread type is desired, a Textron Camcar® Taptite® II
Thread-Rolling Fastener with a 15IP Torx Plus® pan head is available
in lengths of 1/4, 5/16, 3/8, 1/2, 5/8, 3/4, and 1 inch as part number
3BE-P814-00, 3BE-P8123-00, 3BE-P815-00, 3BE-P816-00, 3BE-
4
43755_user_guide 2/1/05 5:00 PM Page 7
Contact Signal Description
1 EXT_ON_OFF External connection for On / Off key input to Daytona LBT
2 EXT_11HZ 90ms “frame sync” signal (used in testing)
3 EXT_GND Power Ground input to Daytona LBT
4 EXT_PWR Power input to Daytona LBT
5 SPKR_AUD Speaker audio output from Daytona LBT
6 DA_TX PCM digital audio output from Daytona LBT
7 DF_RI Data / Fax Ring Indication output from Daytona LBT
8 DF_RTS Data / Fax Request to Send input to Daytona LBT
9 DF_S_TX Data / Fax (UART) data input to Daytona LBT
10 DF_DCD Data / Fax Data Carrier Detect output from Daytona LBT
11 DA_FS PCM digital audio frame sync output from Daytona LBT
12 DA_CLK PCM digital 2.048MHz audio clock output from Daytona LBT
13 DF_S_RX Data / Fax data (UART) output from Daytona LBT
14 0V Signal ground, 0V signal reference and return
15 MIC_AUD Microphone audio input to Daytona LBT
16 EXT_PWR Power input to Daytona LBT
17 EXT_GND Power Ground input to Daytona LBT
18 DPL_TX Digital Peripheral Link (UART) data output from Daytona LBT
19 DF_DTR Data / Fax Data Terminal Ready input to Daytona LBT
20* DPL_RX Digital Peripheral Link (UART) data input to Daytona LBT
21 DF_DSR Data / Fax Data Set Ready output from Daytona LBT
22 DF_CTS Data / Fax Clear to Send output from Daytona LBT
23 0V Signal ground, 0V signal reference and return
24 DA_RX PCM digital audio input to Daytona LBT
25 0V Signal ground, 0V signal reference and return
P8124-00, 3BE-P817-00, and 3BE-P818-00 respectively. A 10IP Torx
Plus® flat head version is also available in a single length of 1/2 inch
as part number 3BE-P801-00. Another 6-32 thread type option is to
insert a helical coil insert with a 6-32 internal thread into these features thus accommodating 6-32 threaded fasteners as mounting
hardware for the 9522A LBT. National Aerospace Standard
NASM122238 serves as a technical reference for the recommended
helical coil insert.
3.5 Connector Sealing in Harsh Environments
If the 9522A LBT is to be used in a harsh environment with exposure
to high humidity or water, the mating of the multi-interface connector must be further sealed to protect from moisture entry. It is recommended that a bead of RTV silicone sealant be placed on the connector mating to the 9522A LBT’s multi-interface connector where
shown in Figure 6 below. A material similar to Permatex 16B should
be used.
Figure 6: Place a bead of Silicone RTV material along this area all
around the connector mating to the 9522A LBT’s multi-interface con-
nector.
4 Electrical Interfaces
The subsections to follow contain interface information for the electrical interfaces of the 9522A LBT.
4.1 DC Power Interface
4.1.1 DC Power Interface Signal Descriptions
The DC power interface is comprised of the DC power inputs and a
control signal as summarized in Table 4 below. The EXT_PWR and
GND inputs are used to supply DC power to the 9522A LBT. The
EXT_ON_OFF control input is pulled to a GND level to toggle the
9522A LBT on and off. Note that both pairs of pins should be connected for EXT PWR and EXT GND.
Table 4: Control/Audio Interface Signal Descriptions
4.1.2 DC Power Input Specifications
The DC power requirements for the 9522A LBT are summarized in
Table 5 below. Note that these requirements apply to DC power
measured at the 9522A LBT multi-interface connector input.
5
Signal Name Signal Description
EXT_PWR (pin 4 and 16) External power +4.4VDC input
EXT_GND (pin 3 and 17) External power GND input
EXT_ON_OFF (pin 1) Power on/off control input
43755_user_guide 2/1/05 5:00 PM Page 8
Table 5: DC Power Input Specifications
4.2 Control/Digital Audio (DPL bus) Interface
4.2.1
Control/Digital Audio Interface Signal
Descriptions
The control/digital audio interface enables peripherals such as handsets and SIM card readers to be interfaced to the 9522A LBT. The
interface utilises an Iridium Proprietary communication bus not
detailed in this fact sheet. Details can be made available after appropriate Non-disclosure Agreements and /or License Agreements are
executed.
4.3 RS232 Data Interface
4.3.1 RS232 Data Signal Descriptions
The RS232 data interface is comprised of eight standard RS232
data, control, and status signals plus a ground level signal reference.
This interface allows a connected Data Terminal Equipment (DTE) to
utilize the 9522A LBT’s modem functionality via AT command control. A 3-wire RS232 Data minimal interface may also be implemented however the 9 wire interface offers better control and is the rec-
ommended implementation.
4.3.2 Autobaud
The Daytona default is for autobaud to be enabled. Autobaud will
occur on the following characters ‘a’, ‘A’, CR (carriage return).
Autobaud will also occur on the escape sequence character, provided this is an odd number character. Normally this is set to ‘+’ in register S2 see AT Command Reference for details.
4.4 Analog Audio Interface
4.4.1 Analog Audio Interface Signal Descriptions
The analog audio interface is comprised of the analog audio input
and output signals referenced to the 0V signal ground as summa-
rized in Table 6 below.
Table 6: Analog Audio Interface Signal Descriptions
4.5 SIM Interface
An integrated SIM chip reader is provided on the 9522A LBT. An
external SIM card reader may also be interfaced as a peripheral to
the 9522A LBT via the DPL bus (control/audio interface). A SIM card
in the external reader will take precedence over the SIM chip in the
integrated connector when both are present.
6
Signal Name Signal Description
MIC_AUD (pin 15) Analog audio input to LBT
SPKR_AUD (pin 5) Analog audio output from LBT
0V (pin 14, 23 and 25) Signal ground
43755_user_guide 2/1/05 5:00 PM Page 9
Parameter Value
Main Input Voltage - Range +4.0 VDC to +4.8 VDC
Main Input Voltage – Nominal 4.4VDC
Main Input Voltage – Ripple 40 mVpp
Peak Input Current (maximum) 2.5 A @ 4.4 VDC
Main Input Active Power (average) 2000 mW
Main Input Standby Power (average) 550 mW
4.6 RF Interface
4.6.1 RF Interface Specifications
The RF interface requirements for the 9522A LBT are summarized in
Table 7 below.
Table 7: General RF Parameters
4.6.2 Radio Characteristics
The tables within this section contain radio characteristics of the
9522A LBT.
Table 8: In-Band Characteristics
Table 9: Link Margin
Note 1: Other antenna options are available
Note 2: Cable losses should be minimized
Note 3: Link Margin given for free space
5 Instructions for the safe Installation and use of
the 9522A LBT
The 9522A LBT is intended for integration into a finished product.
The integrator of the 9522A LBT is required to connect a power supply, antenna, and user interface to the 9522A LBT. To ensure that the
9522A LBT is correctly installed the following general instructions
(sub-section 5.1) are provided for the installer.
The integrator will be required to supply the end user of the integrated product, incorporating the 9522A LBT, with operating instructions
and any other information relating to the maintenance and safety of
the equipment (sub-section 5.2).
5.1 Instructions for the Integrator
The 9522A LBT must be installed by an appropiately qualified
installer and mounted securely as described in section 3.4 of this
document.
The power supply used to power the 9522A LBT must be checked to
ensure it meets the requirements of sub-section 4.1.2 of this document.
Electrical connections to the 9522A LBT multi-interface connector
shall be as designated in Table 3 of sub-section 3.3.1 of this document.
7
Parameter Value
Average Power during a transmit slot (max) 7 W
Average Power during a frame (typical) 0.6 W
Receiver Sensitivity at 50W (typical) -118.5 dBm
Receiver Spurious Rejection at offsets > 1 MHz (typical) 60 dB
43755_user_guide 2/1/05 5:00 PM Page 10
Parameter Value
Frequency Range 1616 MHz to 1626.5 MHz
Duplexing Method TDD (Time Domain Duplex)
Oscillator Stability ± 1.5 ppm
Input/Output Impedance 50Ω
Multiplexing Method TDMA/FDMA
Configuration Cable Loss Link Margin
9522A LBT with accessory antennas 2 dB (Note 2) 13.1 dB (Note 3)
(Note 1)
The current and voltage rating of the multi-interface connector cable
shall meet the requirements of the LBT DC power input.
The electrical characteristics of the multi-interface connector cable
shall not degrade the 9522A LBT digital communications and analog
audio signals.
The multi-interface connector cable will provide adequate screening
from external electromagnetic interference.
The 9522A LBT shall not be located in close proximity to sources of
extreme temperature which will cause it be operated outside of its
temperature specification (-10ºC to +55ºC).
The 9522A LBT shall not be operated without an appropriate antenna connected to its Antenna connector via a suitable 50ohm coaxial
cable. This antenna shall be sited at least 20cm away from any per-
son.
5.2 Instructions from the integrator to the user
To comply with the requirements of sub-clause 1.7.2 (Safety instructions) of the European Information technology equipment safety
standard EN60950-1:2002 the integrator must ensure that:
‘Sufficient information shall be provided to the USER concerning any
condition necessary to ensure that, when used as prescribed by the
manufacturer, the equipment is unlikely to present a hazard within
the meaning of this standard. If it is necessary to take special precautions to avoid the introduction of hazards when operating,
installing, servicing, transporting or storing equipment, the necessary instructions shall be made available.’
As part of these instructions the installer should inform the user that
they should not service the 9522A LBT.
6 Modem Commands and Configuration
The 9522A is configured through the use of AT commands. A full listing of the supported AT commands can be found in the AT Command
Reference document.
8
43755_user_guide 2/1/05 5:00 PM Page 11
Iridium Limited Warranty For Satellite Subscriber
Radiotelephone Products
1. Coverage and Duration
Iridium warrants that its new satellite subscriber radiotelephone
products and accessories (the "Product") shall be free from defects
in materials and workmanship for a period of twelve (12) months from
the date such Product is delivered to the first end user purchaser or
first lessee (the "Purchaser"), or the date such Products are first
placed into satellite subscriber service, whichever occurs earliest.
Iridium, at its option, shall at no charge to Purchaser, either repair or
replace the Product, or refund the purchase price of a Product that
does not conform to this warranty, provided the Product is returned
in accordance with the instructions set out below and within the warranty period. These remedies are Purchaser's exclusive remedies
under this warranty. Repair may include the replacement of parts or
boards with functionally equivalent reconditioned or new parts or
boards. A product that has been repaired or replaced is warranted
for the balance of the original warranty period. A Product for which
a replacement has been provided shall become Iridium's property.
This warranty is made by Iridium to the Purchaser of the Products
only, and it is not assignable or transferable by the Purchaser. This is
Iridium's sole and complete warranty for the Products. Iridium
assumes no obligation or liability for additions or modifications to
this warranty unless made in writing and signed by an officer of
Iridium. Iridium does not warrant any installation, maintenance, or
service of the Products not performed by Iridium.
This Product is covered by a U.S.A. warranty. If the Product has been
sold outside of the U.S.A., Iridium will honor the U.S.A. warranty
terms and conditions only. Outside of the U.S.A., any different warranty terms, liabilities and/or legal requirements of the country in
which the Product is sold are specifically disclaimed by Iridium.
2. Conditions Not Covered By This Warranty
a. Products that are integrated, installed, maintained, or serviced in
any manner other than in accordance with the Iridium user documentation furnished with or applicable to the Product.
b. Product damage caused by the use of ancillary equipment not furnished Iridium, including accessories and peripherals.
c. Problems where the Product is used in a combination with ancillary equipment not furnished by Iridium, and it is determined by
Iridium there is no fault with the Product.
d. Ancillary equipment not furnished by Iridium which is attached to
or used in connection with the Products is not the responsibility of
Iridium, and all such equipment is expressly excluded from this warranty. Furthermore, Iridium does not warrant the integrated operation
of the combination of the Products with any ancillary equipment not
furnished by Iridium.
e. Defects or damage resulting from: use of the Product in any manner not normal or customary; misuse, accident or neglect including
but not limited to dropping the Product onto hard surfaces, immersion in or exposure to water, rain or extreme humidity, immersion in
or exposure to sand, dirt or other particulates, exposure to extreme
heat, spills of food or liquid; improper testing, operation, maintenance, installation, adjustment; or any alteration or modification of
any kind.
f. Batteries manufactured by Iridium and sold with Products whose
capacity exceeds 80% of rated capacity are not covered. Batteries
whose capacity falls below 80% of rated capacity, or that develop
leakage, shall be considered nonconforming. This warranty is void-
9
43755_user_guide 2/1/05 5:00 PM Page 12
ed for batteries if: a) such batteries are charged by other than the
Iridium-approved battery charger specified for charging such batteries; b) any seals on such batteries are broken or show evidence of
tampering; or c) such batteries are used in equipment other than the
Product for which they are specified; or d) such batteries are
charged and stored at temperatures greater than 60 degrees centigrade.
g. Breakage or damage to antennas, or scratches or other damage
to plastic surfaces or other externally exposed parts caused by
Purchaser's use.
h. Products disassembled or repaired in such a manner as to
adversely affect performance or prevent adequate inspection and
testing to verify any warranty claim.
i. Products on which serial numbers or date tags have been
removed, altered or obliterated.
j. Coil cords that are stretched or on which the modular tab is broken; leather cases, which are covered under separate manufacturers' warranties;
k. Products rented on a month-to-month basis.
l. Normal wear and tear.
3. Obtaining Warranty Service
For warranty questions, repairs, or for the return of Product, please
call your Service Provider or Point-of-Sale, not Iridium. Equipment
needing service should be returned to your Service Provider or
Point-of-Sale, not Iridium.
SERVICE WORK PERFORMED BY SERVICE CENTERS NOT AUTHORIZED BY IRIDIUM TO PERFORM SUCH WORK WILL VOID THIS
WARRANTY.
All Products shipped to Iridium's authorized Warranty Service Center
must be shipped with freight and insurance prepaid. Purchaser must
include with the Product a bill of sale, a lease, or some other comparable proof of purchase, the name and location of the installation
facility, if any, and most importantly, the Purchaser's name, address,
and telephone number and a written description of the problem.
Product that is repaired or replaced under this warranty shall be
returned to Purchaser at Iridium's expense for the freight and insurance, and at Purchaser's expense for any applicable duties or other
charges. If additional information is needed, please contact Iridium
at the address and phone number listed in Paragraph 7 below.
4. General Provisions
THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. FURTHER, THIS WARRANTY COVERS
THE PRODUCTS ONLY, AND NO WARRANTY IS MADE AS TO COVERAGE, AVAILABILITY, OR GRADE OF SERVICE PROVIDED BY IRIDIUM SEPARATELY FOR IRIDIUM SATELLITE SERVICES. IN NO
EVENT SHALL IRIDIUM BE LIABLE FOR DAMAGES IN EXCESS OF
THE PURCHASE PRICE OF THE PRODUCT IN QUESTION, OR FOR
ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL,
SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT
SUCH MAY BE DISCLAIMED BY LAW.
5. Conditions of Use and Disclaimer of Liability
Users of the Iridium Satellite LLC ("Iridium") mobile satellite phone
service and related equipment, including without limitation those
using the phone service and equipment in any manner in conjunction
10
43755_user_guide 2/1/05 5:00 PM Page 13
with emergency 911or emergency 112 or any other distress calling or
emergency services, both public of privately operated, acknowledge
and agree as a condition of the provision of phone service and
equipment by Iridium that they will make no claim, whether in contract, tort or otherwise, against Iridium for bodily injury, loss of life,
damage to property or for any other loss whatsoever, or for special,
incidental, indirect, consequential or punitive damages, by reason of
any unavailability, delay, faultiness or failures of the Iridium facilities
or phone service or equipment or for inaccuracies or failures with
regard to any user information provided. This is a waiver and release
and disclaimer of liability to the fullest extent permitted by applicable law and applies regardless of the cause of any liability, including
without limitations, to wrongful conduct, omission or fault of employees or agents of Iridium.
Iridium makes no warranties, express or implied, including any
implied warranty of merchantability or fitness for a particular purpose concerning Iridium service or equipment. Iridium cannot promise uninterrupted or error free service.
The Iridium service does not currently interact with E911 or E112 or
other public emergency services. Such calls are not able to be made
on the Iridium system.
Users by their use of the phone service and equipment consent to
Iridium's disclosure of user information, including but not limited to
name, address, telephone number and location information, including the geographic coordinates of equipment, to governmental and
quasi-governmental agencies such as emergency service providers
and law enforcement agencies, where Iridium deems it necessary in
its sole discretion to respond to an exigent circumstances. These
governmental and quasi-governmental agencies shall be deemed
"users" for all purposes of this Disclaimer of Liability.
6. State Law and Other Jurisdiction Rights;
Software Copyrights
SOME STATES AND OTHER JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY
NOT APPLY TO PURCHASER.
This warranty gives Purchaser specific legal rights, and Purchaser
may also have other rights which vary from jurisdiction to jurisdiction.
Laws in the United States and other countries preserve for Iridium
certain exclusive rights for copyrighted Product software such as the
exclusive rights to reproduce in copies and distribute copies of such
Product software. Product software may be copied into, used in and
redistributed with only the Product associated with such Product
software. No other use, including without limitation disassembly, of
such Product software or exercise of exclusive rights in such
Product software is permitted.
7. Contact
For additional information about this Product warranty, please contact your Service Provider or Point of Sale.
For additional information about Iridium products and services,
please contact Iridium as follows:
By Telephone: Customer ServiceToll Free Number: +1-866-947-4348
Local or International Number: +1-480-752-5155
By Email: Info@iridium.com
By Mail: Iridium Satellite LLC
Attn: Customer Service
8440 S. River Parkway, Tempe, AZ 85284 USA
11
43755_user_guide 2/1/05 5:00 PM Page 14
E C Directive
Declaration of Conformity
This is to certify that the following equipment complies with all relevant Essential Health and Safety Requirements of the Radio and
Telecommunications Terminal Equipment Directive 1999/5/EC and
the Low Voltage Directive 73/23/EC as amended by 93/68/EC.
Equipment description Iridium 9522A Satellite L-band transceiver
Manufacturer Iridium Satellite, LLC • 8440 South River Parkway,
Tempe, AZ 85284 USA
The following harmonised standards have been applied to the design
of the L-band transceiver:
Standard Description
EN 60950-1:2001 Information technology
equipment - Safety - Part 1:
General requirements
EN 301 489-20V1.2.1 (2002 11)
EN 301 489-01V1.4.1 (2002-08) Electromagnetic compatibility
and Radio Spectrum Matters
(ERM);ElectroMagnetic
Compatibility (EMC) standard for
radio equipment and services.
ETSI EN 50360:2001 Product standard to
demonstrate the compliance of
mobile phones with the basic
restrictions related to human
exposure to electromagnetic
fields (300MHz to 3GHz)
ETSI EN 301 441 V1.1.1 05/2000 Satellite Earth Stations and
Systems (SES); Harmonised EN
for Mobile Earth Stations MESs)
A “technical file” is retained by Iridium Satellite LLC. Related test
reports are available upon request directly from Iridium Satellite LLC.
The 9522A L-band transceiver is declared conformant only if it is
used in the configuration tested and if the L-band transceiver is used
as described in the 9522A User Guide.
Signed _____________________________ CTO, Iridium Satellite, LLC
Date __________________________
12
43755_user_guide 2/1/05 5:00 PM Page 15
Iridium Satellite LLC Headquarters
6701 Democracy Blvd., Suite 500
Bethesda, MD 20817 USA
Phone +1.301.571.6200
Fax +1.301.571.6250
Iridium Satellite LLC
8440 S. River Parkway
Tempe, AZ 85284
Toll Free +1.866.947.4348
Local or International +1.480.752.5155
Fax +1.480.752.1105
email info@iridium.com
www.iridium.com
LUG0501
43755_user_guide 2/1/05 5:00 PM Page 16
Loading...