H.264/H.265 (HEVC)
IPTV ENCODER & STREAMER
SERIES
OVERVIEW AND QUICK START
USER MANUAL
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 2 -
APPLİCATİON EXAMPLE:
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 3 -
Thank you for choosing our products. Plea se contact us if you have any question – see last page
This manual applies to the following models: (depending on changes in model types and ranges
this is a subject to change w/o further notice)
H.264 Video Encoder Series
HDE-264
One channel HDMI H.264 encoder
• Support H.264Baseline Profile / H.264Main
Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
VGE-264
One channel VGA H.264 encoder
• Support H.264Baseline Profile / H.264Main
Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF
SDE-264
One channel SDI H.264 encoder ,with one
channel SDI looping out
• Support H.264Baseline Profile / H.264Main
Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support 1080P@60fps
•
Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
ADE-264
Mini HDMI+CVBS H.264 video encoder
• Support H.264Baseline Profile / H.264Main
Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 4 -
VHE-264
H.264 HDMI+VGA decoder
• H.264Baseline/High/Main Profile decoding
• MJPEG/JPEG Baseline decoding
• Audio decoding MPEG1 Audio Layer 2
• Support Network interface full-duplex mode 100M
• 1 channel HDMI/vga/audio output
• Support up to 1080P/60hz HD video output
• Support HTTP, UTP, RTSP protocol
HDE-16264
16 channels HDMI H.264 encoder in rack
• Support H.264Baseline Profile / H.264Main
Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF
ADE-16264
16 channels HDMI + CVBS H.264 encoder
in rack
• Support H.264Baseline Profile / H.264Main
Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF
HDE-4264
4 channels HDMI H.264 video encoder
• Support H.264Baseline Profile / H.264Main
Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
•
Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF
• Dimensions : 430mm x 250mm x 45mm
(LxWxH)
• Net Weight: 3KG
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 5 -
ADE-4264
4 channels HDMI + CVBS H.264 video
encoder
• Support H.264Baseline Profile / H.264Main
Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF
• Dimensions : 430mm x 250mm x 45mm
(LxWxH)
• Net Weight: 3KG
SDE-4264
4 channels SDI H.264 v ideo encoder
• Support H.264Baseline Profile / H.264Main
Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support 1080P@60fps
•
Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF
•
Dimensions : 430mm x 250mm x 45mm
(LxWxH)
• Net Weight: 3KG
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 6 -
19” 1 RU Encoder Series
ADE-1264
H.264 Video Encoder into 1 RU case with
HDMI input+BNC input+Independent Audio
• Support 1080P@60fps
• Single channel IP output
• Support HTTP,RTMP,RTSP,UDP,ONVIF
protocol
• Support unicast and multicast
HDE-1265
H.265 Video Encoder into 1 RU case with
HDMI input
• Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps
SDE-1265
H.265 Video Encoder into 1 RU case with
SDI input
• Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps
HDE-4264
H.264 Video Encoder into 1 RU case with
4CH HDMI input
•
Support 1080P@60fps
• 4 channel IP output
•
Support HTTP,RTMP,RTSP,UDP,ONVIF
protocol
• Support unicast and multicast
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 7 -
H.265 (HEVC) Video Encoder Series
HDE-265
One channel H.265 HDMI video encoder
• Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps
SDE-265
One channel H.265 SDI video encoder
• Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps
VDE-265
One channel H.265 VGA video encoder
• Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps
HDE-
1265
H.265 Video Encoder into 1 RU case with
HDMI input
• Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps
SDE-
1265
H.265 Video Encoder into 1 RU case with SDI
input
• Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 8 -
H.264/H.265 Wireless Video Encoder Series
SWE-264
1 channel SDI input encoder
•
Connect the internet by Wifi or ethernet port
• 1 Channel SDI input;
• 1 channel SDI loop output.
• Same specification as SDE-264
SWE-265
1 channel H.265 SDI video encoder with 1
channel SDI loop out with wifi
•
Connect the internet by Wifi or ethernet port
• Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps
HWE-264
One channel HDMI H.264 en coder with wifi
• Support H.264Baseline Profile /H.264Main
Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
Almost all models with ONVIF support can be used with following protocols:
“ONVIF S, “ONVIF C” or “ONVIF G”
Statement:
Text and pictures herein are subje ct to chang es w/o notifications.
The user manual will be updated in real time without special notice.
This user manual is provided only as a reference guide for technicians as examples.
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 9 -
Default Values
The factory default administrator account: admin
The factory-default user password: admin
The factory default IP address: 192.168.0.31 or 192.168.1.168
Please change these account settings according to your local policy and network. -> Do not forget to
safe and backup the configuration.
1 PRODUCT OVERVIEW
The H.264/H.265 Encoder is a hardware device used for high-definition video si gnal (up to 1080p HD
resolution) encoding and network transmission, using the latest and high-efficient HD digit al video
compression technology H.264/H.265, with the characterist ics of reliable, high-definition, low bitrate and
low latency. Connect the HDMI/SDI/VGA high-definition video signal to start the encoding process, after
the compression processing by the DSP chip, the output of the standard TS network stream can be
started.
The launch of these devices fills the gap in the industry, which is a direct replacement for the traditional
capture card for software coding method, usi ng hard-coded chipsets, the system is more stable, and the
picture quality is more perfect. They can be used in a wide variety of demands for high-definition video
and high-resolution / h igh frame rate re-assembling for IP based network transmission. Its powerful
scalability makes it more easier to respond to the needs of different industries and can be used as live
video encoder. Industrial controlled, precision desi gn, small size, easy inst al l ation, t he power is less
than 5W, which is energy-saving and more stable.
2 PRODUCT FEATURES
• High-performanc e hardware encoding
• h.265 video coding efficiency (depending on Model, downward compatible to h.264)
• h.264 BP/MP/HP
• AAC / G.711 Advanced Audio Coding format quality
• CBR / VBR rate: 16Kbps ~ 12Mbps
• 1000Mbit/s network interface using ful l duplex mode
• A mainstream and second stream can be sent to different IP-connections
• Supports up to 720P, 1080P @ 60HZ HD video input
• Support image parameter settings
• HDCP protocol and Blu-ray
• HTTP, UTP, RTSP, RTMP, RT P, ONVIF protocol
• The mainstream and second stream can be used with different network protocol for their
transmissions
• WEB int erf ace with 2 Languages: English and optional Chinese for Asian customers
• Support remote management in WAN (WEB)
• Support customized settings for the resolution
• Support one step to restore the factory configuration
• Support SDK / individual development
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 10
-
3 APPLICATIONS
• IPTV
• Digital Signage
• Video Conf erenc e
• Hotel IPTV System
• Live Broadcast Feeds
• Campus IPTV System
• IP Recording System
• Medical video broadc ast and recording syst em
• Live video educat i on system
• IP Video Recording (DV R/NVR)
• 4G mobile broadcast HD front capturing
4 INTERFACE DESCRIPTION
4.1 The interfaces of H.264HDMI encoder and WIFI encoder are almost similar：
4.2 The interfaces of H.264SDI encoder and WIFI encoder are similar：
4.3 H.264VGA Encoder：
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 11
-
4.4 HDMI CVBS HD Encoder：
4.5 The interfaces of H.265 HDMI encoder and WIFI encoder are similar：
4.6 The interfaces of H.265 SDI encoder and WIFI encoder are similar：
4.7 The interfaces of H.264VGA encoder and WIFI encoder are similar：
From Left to Right:
A. Power input----- 12V/DC（12V/1A，5V/2A optional）
B. RST=RESET button ------ useful to reset the device to factory defaults . After power on ,
press it for about 15 seconds to reset the device to default IP 192.168.0.31
(192.168.1.168 – depending on Model)
C. AUDIO/Video input------ Input HD HDMI, SDI, VGA, Audio signals
D. 1000BaseT Ethernet port RJ45
E. Status Indicator：
1) Will flash while pressing the RESET button. Reset is successful when the light turns
off . Slow Flashing show: Video input , image capturing and compression is working..
2) If the indicator light keeps on, the Video source acquisition and compression has
some problem like resolution/format our out of Input specification. Sync failed...
3) If the indicator LED flashes slowly but the output stream is not working , there might
be a problem with the streaming server part.
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 12
-
5 WEB SERVER SETTINGS
Step 1: Reset & initialization
Connect the power supply to turn on the encoder and use a pin to press RST on the encoder
for min. 10 seconds (better 15), it will be restarted and initialized. The default Route IP of the
WEB-IF is 192.168.0.31 or 192.168.1.168 (
This default Address may vary depending on model) after
initialization and can be recognized from the sticker at the bottom:
Step 2: Change the administrator’s computer IP
Set the administrator’s computer IP as: 192.168.0.* or 192.168.1.*to avoid IP conflicting with
the units own IP address IP 192.168.0.*: (use an IP setting “*” in the number range between
2-254 except .0.31 or .1.168) Remark: .0 is often the network router, .1 often the Gateway of
the used router.
Step 3: Login the menu with the web browser:
Enter 192.168.0.31 (or 192.168.1.168) in your Browser window.
Default user Name: admin
Default password: admin
You might end up in the chinese Language Menu if operating the unit for the first time: (That migh t
be obsolete depending on SW Versions...)
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 13
-
So please change it to English using the submenu upper right corner use the 2nd item:
You are entering the STATUS window:
You'll get more information if scr oll ing down:
The sub-menus are at the bottom.
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 14
-
Enter Network settings submenu (bottom-menu):
DHCP might not be a good idea because your local network router would handover an
IP Address from his pool which you can only get by entering the router itself.
Remark: DNS settings might not be necessary because the device would not need to
use them to translate domains <-> IP addresses.
Please change the settings to your local network values and scroll down to safe it by
pressing SET UP:
You can set the DNS values
according to your local router
values. The HTTP and RTSP
ports should be set for the unicast
/ http streaming default selected
ports
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 15
-
Enter the SYSTEMS Menu to reboot your device and to enable the new settings
or do a SW-update:
configure a planned scheduled restart:
Or upgrade the Firmware and initialize a reboot:
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 16
-
Do not forget to re-adjust your PC/LAPTOP IP-Settings to your local network addresses
if you changed the IP address.
Re-enter into the unit's WEB-IF by using the new address.
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 17
-
5.1 STATUS DİSPLAY
Input status: when you input the HD signal source, it will show resolution of video input, if it’s
blank here: No video input detected .
Main-stream Status: Showing the resolution of the main-stream you set and multicast address.
You can control the multicast address by VLC or other Video receiving software supporting
that.
Second (Sub) stream Status: Showing the resolution of the second-stream and its configured
address:
Note: The Preview is only possible
if already configured:
Popup:
Please open FLV or HLS stream.
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 18
-
5.2 NETWORK SETTINGS - WIFI
You can set the network with either Ethernet or WIFI. Only devices with WIFI support can use a
WLAN connection.
Instruction of wifi network Setup: 3 different settings can be chosen
A. Ethernet: Only connected by ethernet (default configuration)
B. Wifi: Only connect with WLAN . Hint: If you entered the wrong password or SSID during
WIFI mode will cause the system being unable to connect to Wirelesss LAN. Opening the webInterface will fail. Please press the reset button to restore the default settings to solve the
problem)
C. Auto: Automatically detect if you have ethernet or wifi connected.
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 19
-
a. The Default IP of the device is 192.168.0.32 (depending on model) . If IP setting has been
forgotten after changing, you can RST= reset it to default IP following the reset to default
settings procedure like explained before.
b. If you don’t need to use a network cable, and when you reboot the device, it will access to
WIFI status if it’s equipped with WIFI . Please kindly note the different features for WIFI
versions.
5.3 MAIN STREAM ENCODI NG SETTINGS:
We assume, that the user already well knows the relevant terms and abbreviations for
Video-Encoding and their technical background.
Chose your codec:
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 20
-
MAİN STREAM SETTİNG:
Enc type: h.264 & h.265 (is optional dep. on model)
Note: h.264 version can only use h.264 codec, h.265 model can both
Profile: baseline profile / main profile / high profile ( note: h.265 version choose main
profile)
Frame rate: 5-60 (If the input resolution is 720i/50,1080i50, the frame rate will be set to
25)
Bitrate mode: VBR / CBR variable or constant (incl. zero pakets)
Group of picture: 5-200, shows picture quality, default setting is almost sufficient
Bitrate: 16-1200K (Network bandwidth setting)
Note: You can modify the above parameters without rebooting the encoder
SELECTİNG YOUR OUTPUT SCREEN SİZE/RESOLUTİON:
Note: The encoder is not intent to use for upscaling purpose i.e. 720 -> 1080. It
always depends on the Input resolution and size. Downscaling is possible:
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 21
-
Main - Stream protocol settings:
HTTP: /main enable/disable
HTTP port: 1-65535 optional
RTSP: /main enable/disable
RTSP port: 1-65535 optional
Multicast IP: 232.255.42.42 disable/RTP/UDP optional
Multicast port: 1-65535 optional
RTMP server IP: can be set according your streaming media server values
RTMP server port: 1-65535 optional
RTMP app name: can be set by yourself
RTMP stream name: can be set by yourself
RMTP user name: User for your server
RMTP password name: and Password for your server
ONVIF : enable/disable (IP-Camera protocol support)
Note: ONVIF Settings depending on SW and device model types
Note: We recommend to chose not all streams and protocolls at the same time.
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 22
-
Note: For TS URL, HLS URL, RTSP URL, the Network IP address of the device is the Unicast
distribution address. You do not need to fill in this addrerss by yourself becasue its already related
to the GbE network IP.
Multicast IP adresses and ports need to be considered in the IANNA recommended range to avoid
conflicts within your local network and router/switches:
https://www.iana.org/assignments/multicast-addresses/multicast-addresses.xhtml
TS once pack:
is the packet size send by the encoder streamer.
Usually we suggest to set it to 7.
For example for UDP:
1 packet is 188, 7 pack size will be 188*7+46=1 36 2
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 23
-
MAİN STREAM LİVE VİEW:
You can play the stream address by your computer if you installed i.e. the VLC Player software
or use an IPTV STB by setup the RTSP or HTTP stream addresses:
Easiest way: copy and paste the URL from the main window
and open VLC – network stream:
Press Play/Wiedergabe:
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 24
-
You can check the video information if you like by VLC:
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 25
-
Second stream Live View: You can play the stream address by your computer if you installed
the Video Lan Client (VLC , freeware for almost all plattforms) similar to the shown procedure
above.
CVBS Live View (depending on Model): You can play the stream address by your computer if
you installed the VLC.
5.4 OSD SETTINGS (OVERLAY A PICTURE/TXT TO THE E NCODED STREAM)
To be able to OVERLAY text and advertisements to your encoded stream, the unit supports up to
4 zones:
Note: You can insert two couples of TEXT and 3 pictures simultaneously overlaying the picture
Tex1 X: 0-1920 is optional, display the left and right position of the text
Tex1 X: 0-1080 is optional, display the up and down position of the text
Font1 size: 8-72 is optional
Alpha1: 0-128 is optional, Alpha-blending – transparency setting
Color1: choose the color you want to display
Bg1: choose background color for the text on the video overlay
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 26
-
Tex1: input the content of the text you want to display
These features are varying depending on model and versions.
or a prepared picture according to the values given in the WEB-IF for uploading to the unit:
looks like there is a translation issue of the upload-button ;-)
OSD insertion Picture Setting
Picture1…4: disable/ enable (disable: no images , enable: insert the images)
Pictures X: 4-1920 is optional to set the left and right position of the picture
Pictures Y: 4-1080 is optional to set the up and down position of the picture
Alphal: 0-128 is optional
Picture1 name: display the name of the picture1
Upload picture1: choose to upload the image, supporting *.bmp format of the picture and
limited filesize : less than 500kbyte
Requirements
• The settings of the three pictures to be inserted must be identical.
• Transparent background of the picture setting:
should be of RGB values: R－177，G－204，B－233 or see WEBIF hints
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 27
-
example:
Picture quality setting (dep. on model)
Brightness: 0-100 is optional (to adjust the brightness of the image)
Contrast: 0-100 is optional (to adjust the contrast of the image)
Hue: 0-100 is optional (to adjust the hue of the image)
Saturation: 0-100 is optional (to adjust the saturation of the image)
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 28
-
CSC:
is for Video color, Contrast & brightness settings just in case the user want
to change them appart from the original passed Picture settings.
HINT: If you change parameters or enable features, following popup message will
appear:
This doesn't mean to restart your encoder! – It means your Receiver sho uld be tuned
again to the stream (i.e. switch or reload the channel on your Irenis IPTV SetTopBox to
re-initialize the decoding process)
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 29
-
SECOND (SUB) STREAM OUTPUT SETTINGS
Note: The method of the setting is nearly the same with mainstream code setting:
The sub-Stream has some slightly different setup:
Because the RTMP Server can only obtain a stream once from the same address.
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 30
-
Please asure the corresponding picture settings if downscaling i.e. from 16:9 to 5:4 would
squeeze the picture:
5.5 CVBS ENCODING SETTINGS (DE P. ON MODEL)
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 31
-
5.6 AUDIO ENCODING SET TINGS
Audio bitrates: 48k, 64k, 128k, 160k, 192k, 256k
Audio type: AAC (depending on model) and more...
Audio digital gain: 2x, 4x, 8x, used to adjust volume
Audio input mode: digital/analog
Example 1:
Example 2:
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 32
-
6 WIFI SETTING HİNTS
Hint shown above: If you want to configure the HD encoder, you need to set the fixed IP of the
computer first . See chapter above – similar to Ethernet Settings.
6.1 HD WIRELESS ENCODER SETT INGS
Connect the HD Encoders by the network cable, then open the browser to enter the network
setting chapter. Default setting as shown below can be modified to your needs:
Note:
1) Default IP of wifi can be 192.168.0.32 . When wifi connected successfully, you can access
to web control panel by 192.168.0.32 .
2) Wifi Encryption : WPA/WPA2 (Note: Some wireless routers have different encryption
mode, please select WPA/WPA2 for the encryption )
3) Input the WEP/WPA password string of the wireless router
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 33
-
7 TECHNICAL SPECIFICATIONS (DEP. ON MODEL)
Video
Input HDMI, SDI, CVBS according to the chosen model
Resolution 1920×1080_60i/60P, 1920×1080_50i, 1280×720_60p,
1280×720_50p and below
Encoding H.264/AVC Main Profile/High Profile ; H.265/HEVC Baseline
Profile; Audio AAC
Data Rate 0.8 Mbps ... 12 Mbps
Rate Control CBR/VBR
GOP Structure IBBP
Advanced Pretreatment De-interlacing, Noise Reduction, Sharpening
Audio
Encoding AAC, MP3
Sampling Rate Auto
Bit-rate 48K/64K/96K/128K/160K/192K/256k
Sampling Precision 16 bit
Data Rate 64 Kbps ~ 384 Kbps
System
System Support WINDOWS; LINUX
Ethernet/RJ45 1000Base-T Ethernet interface
Protocol HTTP, UDP, RTP, RTSP, RTMP, ONVIF (prot.: S,C,G)
Control Interface 100baseT by WEB-Browser
SAFETY AND OT HER RECOMMENDATİONS:
Assure climatic environment rules for electronic machines like this, Grounding rules as
well. Installation should be done by a certified electrician.
Important Notes!
This manual is for use by qualified personnel only. Handling this device or system requires special
electronic technical knowledge. To reduce the risk of electrical shock or damage to the equipment,
do not perform any servicing other than the installation and operating instructions contained i n this
manual unless you are qualified to do so. This device operates in the given voltage and frequency
range without requiring manual adjustment.
Do not open the top case w/o unplugged power source because serious injury or death may be
the result! Inside are components under risk from electrostatic discharge. To avoid equipment
damages do not touch these components or, observe the respective handling rules!
For continued protection against fire, the fuses may only be replaced by identical fuses with the
same electrical specifications which are designed for the corresponding fus e positions.
No part of this publication may be reproduced in any form or by any means or used to make any
derivative work (such as transl ation, t ransf ormati on or adaptat i on) without the written permiss i on
from Blankom / IRENIS GmbH.
IRENIS Encoder & Streamers | User Manual
Author: Rri, August 2017, Version: V1.3 - 34
-
IRENIS GmbH reserves the right to revise this publication and make changes in its content from
time to time, whereby it shall not be obligatory for IRENIS GmbH to provide notification of such
revision or change.
IRENIS GmbH provides this manual without warranty of any kind, neither implied nor expressed,
this
includes also any warranties regarding the merchantability and fitness for a partic ul ar purpose.
IRENIS GmbH may improve this manual or make changes in the products described herein at any
point of time.
Installation Notes
All types of the IRENIS-BLANKOM family are single or 19“devices with 1 RU height might be
designed for installation in 19” racks. In addition to the front panel screws an internal module
support is required at the rack. Depending on the Frontend used and the operating adjustments,
the RF-input port carries DC Voltage (13V /18V, max. 400 mA).
By connecting a mains cable, the device can become functional without any auxiliary appliances.
The power supply units are designed for the wide range of 100-230V AC; a manual adjustment of
the voltage is not necessary.
For some models the second power connector is feeding another independent power supply for
internal redundancy. For a maximum of redundancy both power supplies should use different
circuits.
All the outputs are decoupled from one another. Thus, the circuit does not have any effect on the
functioning of the device. Connections that are not required need not to be terminated.
Suggestion: CAT 6E Ethernet cable for GbEthernet
CONTACT:
IRENIS GmbH
Owiesenkehre 1
D-22177 Hamburg - Germany
Managing Director: Dipl.Ing. Riccardo Rossini
Commercial Register: HRB 130657 / District Court Hamburg
Web: www.blankom.de E-Mail: info@blankom.de / info@irenis.com
Irenis-Direct Phone: +49 40 459747 Technical Hotline: +49 40 22864848
Loading...