IQSIM M10 User Manual

M10 WiFi Hotspot

M10 overview Function description

Screen

Power Button

Power Button Long press the power button for 3 seconds to power on. Long press the power button for 15 seconds for Factory reset.

Micro SIM Card Slot

For extension – Not used.

Network standards

Support multi-bands GSM/WCDMA/LTE

FDD : B1, B2, B3, B4, B5, B7, B8, B17, B20

TDD : B38, B39, B40, B41

WCDMA 850/900/1900/2100

GPRS/EDGE 850/900/1800/1900

Maximum downstream rate 150Mbps

Maximum upstream rate 50Mbps

Battery

Battery capacity : High-capacity battery of 5000mAh

Charging voltage: DC 5V 1A

Full charging: 6 hours required

Battery life: Standby for 24 hours. In using for 12 hours.

Note-1: The ambient temperature should be 0 ℃ - 45 ℃; 20%

battery

capacity would be lost after normal using for one year.

Note-2: Do not over charge or discharge, users are highly recommended to

recharge every 2 months if not used.

Micro SIM card slot

Input charging port

Instructions

How to connect to M10 Hotspot:

1) Subscribe Internet Service

To ensure internet access, please contact your reseller to subscribe internet service.

2) Start the M10 WiFi Hotspot device

After power on, M10 device takes 1 or 2 minutes to connect and access to the preferred local network. Connection details will be displayed on the screen.

3) Connect to the M10 WiFi access point

On your smart phone or tablet, search for M10 WiFi access point and connect using password displayed on M10 screen. You can start to enjoy internet access service.

Input Charging Port

Charge device through data cable.

Screen Display of M10 device information, network connection status and usage.

Screen

Interactive screen gives you information once the device is

connected to the network.











1) Battery icon (

2) WiFi network active

3) Network type (2G/3G/4G)

4) Signal strength

5) Page menu

means it is in charging)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - -

Maximum rate 150Mbps

Support 802.11 b/g/n

Support band 2.4G

Support 5 devices simultaneously

Screen

Short press the power button to switch to menu:

Press 3s on power button to shut down the device

M10 hotspot name (SSID) Password (PWD)

Data consumption / available package Remaining time

Country where is located the device Network operator used by the device

Device serial number (S/N) Software version

2/6: Press 3s to confirm

SSID : M10_123456 PWD : 12345678

3/6

4/6

FRANCE F-Bouygues Telecom

5/6

S/N : 12345678912345 Version : 1.00.001

6/6

POWER OFF

153MB/2GB

13H42min

Precautions

Please read the following precautions before using:

1) Handle with care, device should be kept cleanly.

2) Do not put in place with wet, water or other liquids.

3) Do not put in place of extremely high or low

temperatures.

4) Do not put near flame or lit tobacco.

5) Do not drop, throw, bend or demolish.

6) Do not put or install on top of car airbags.

7) Altitude:≦2000 meters, the power adapter determines

the applicable altitudes for using.

Environmental declaration

The following statements are in line with relevant provisions of the "Electronic Information Products Pollution Control Management Measures" of the People's Republic of China. Listed declaration applies to M10 device:

Name M10 Device Accessories

Lead

Mercury

Cadmium

Hexavalent Chromium

Cr6+

Polybrominated Biphenyls

Polybrominated Diphenyls Ethers

O: Indicates that this toxicor hazardous substance in all homogeneous materials are within thel imitrequirements in SJ / T 11363-2006 standard. X: Indicates that this toxicor hazardous substance contained in at least one of the homogeneousmaterials is in excess of requirements in SJ / T

11363-2006 standard. The maximum value of SpecificAbsorption Ratio(SAR) in this product is 0.9W/kg, in accordancewith national standard GB21288-2007.

PBB

PBDE

O O

For Customer Service, please contact your reseller.

FCC RF EXPOSURE INFORMATION:

WARNING!! Read this information before using your phone

In August 1986 the Federal Communications Commission (FCC) of the United States with its action in Report and Outer FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards. Use only the supplied or an approved antenna. Unauthorized antennas modifications, or attachments could impair call quality, damage the phone, or result in violation of FCC regulations. Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for replacement antenna.

BODY-WORN OPERATION:

This device was tested for typical body-worn operations with the back/front of the phone kept 0cm from the body. To comply with FCC RF exposure requirements, a minimum separation distance of 0cm must be maintained between the user's body and the back/front of the phone, including the antenna. Third-party belt-clips, holsters and similar accessories containing metallic components shall not be used. Body-worn accessories that cannot maintain 0cm separation distance between the user’s body and the back/front of the phone, and have not been tested for typical body-worn operations may not comply with FCC RF exposure limits and should be avoided. For more information about RF exposure, please visit the FCC website at www.fcc.gov

Your wireless handheld portable telephone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals. In August, 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless phones. Those guidelines are consistent with the safety standards previously set by both U.S. and international standards bodies:

<ANSIC95.1> (1992) / <NCRP Report 86> (1986) / <ICNIRP> (1999)

Those standards were based on comprehensive and periodic evaluations of the relevant scientific literature. For example, over 120 scientists, engineers, and physicians from universities, government health agencies, and industry reviewed the available body of research to develop the ANSI Standard (C95.1). Nevertheless, we recommend that you use a hands-free kit with your phone (such as an earpiece or headset) to avoid potential exposure to RF energy. The design of your phone complies with the FCC guidelines (and those standards).

Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the phone and may violate FCC regulations.

NORMAL POSITION:

Hold the phone as you would any other telephone with the antenna pointed up and over your shoulder.

RF Exposure Information:

This product is compliance to FCC RF Exposure requirements and refers to FCC website https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm search for FCC ID: 2AK8BM10 to gain further information include SAR Values.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

+ 1 hidden pages