IQ Group QS5 02WD3130 User Manual

Entrance Alert
Model WD5080

1x Magnetic piece,
1x Transmitter)

Installation instructions: Please retain for future reference.

This Package Contains:

• Plug-In Alert

• Magnetic Piece, Transmitter & CR2032 Lithium coin cell battery

• 4 screws and 4 wall plugs for mounting the Magnetic piece & Transmitter

You will require:

• A small Phillips head and Flat head screwdriver

Installation Instructions

For interior use only.
Please note: Installing the Transmitter or plug-in alert on or near metal
structures or reinforced PVC doors or doorframes may reduce the transmission
range.

Open the Transmitter and Magnetic piece as shown in
Figure 1.

Remove the front cover by inserting a flat head screwdriver
into the slot and twist gently.

LED Light (A)

Install the battery for Transmitter (Refer to Figure 2)

Position the front cover as shown and slide the CR 2032
Lithium battery into the holder as shown, with the + side of
the battery facing you.

Install the Transmitter and Magnetic piece

Ensure the frame of the door or window is flat, clean
and dry. Mount the bases using the screws and wall
plugs provided (See Figure 3). Install both units
vertically. Align the arrows make sure both the
Magnetic piece and Transmitter are on the same level
of surface (See Figure 1). Do not mount the
Transmitter on or near large metal objects as this can
block signals from the wireless Transmitter.

Transmitter

Figure 2

Snap the front cover to the base. To
ensure a good alignment, adjust the
front cover of the Magnetic piece by
pushing or pulling the cover in and out
(3 adjustment levels).

Install the Plug-in Alert (Refer to Figure 4)

Figure 3

Plug the Plug-in Alert into any 120 VAC
outlet in the house. The Plug-in Alert must be
within 150 feet of the Transmitter. The Plug­in Alert will play 2-note and 1-note sounds
when it is first powered up.

Figure 4

Program Transmitter to the Plug-in Alert
(Refer to Figure 5)

Program the Transmitter. Open the door or window. A Ding-Dong should be
heard indicating the transmitter has been programmed to the Alert. Close the
door or window. A Ding should be heard. The LED light (A) will illuminate
indicating the transmitter is working.

Magnetic
piece

Transmitter

Figure 1

Align arrow for
installation

Transmitter

Magnetic

Piece

3 adjustment
levels

Figure 5

Specification

Range………………..up to 150 ft.
Electrical Load………1 x CR2032 Lithium Battery for Transmitter

Note:

This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:

(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that

The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. To comply with FCC
RF exposure compliance requirements, this device and its antenna must not be co-located or
operated in conjunction with any other antenna or transmitter.

may cause undesired operation.

To Reset the Alert Programming, press and hold
button B in Figure 6 until the plug-in chime sounds.

B

The chime will play the tunes available indicating
that previous programs have been erased. Return to the
Program Transmitter to the Plug-in Alert section and
repeat.

Figure 6

Troubleshooting

Alert doesn’t sound when door or window is opened or closed

Check that the battery has been inserted correctly. The LED light should
come on when the Transmitter moves closer to or away from the Magnetic
piece.
Transmitter may be positioned out of range of the Plug-in Alert. Move
the Plug-in Alert closer to the Transmitter.
A metallic object may be blocking the signal to the Plug-in Alert from the
Transmitter position. Experiment with the location of the Plug-in Alert to
see if you can move it to a more suitable place.

Battery in the Transmitter may need replacing.

The Transmitter LED will flash 5 times when the battery needs replacing.
See instruction for Installing the Battery.
Note: In cold conditions, poor location or environment, operating at
maximum range it is advisable to replace the battery more frequently (i.e.
every 12-18 months) to maintain optimum performance.
Your Transmitter and Plug-in Alert haven’t been programmed. Reset the
automatic programming of your Plug-in Alert by pressing and holding down
button B (Figure 6) for 5 seconds. The alert will sound indicating the
programming has been erased. Program the Transmitter following the
installation instructions.
For any other problem, call 1-800-296-1869 between 9am and 5pm EST.

IQ America Two Year Warranty

This is a “Limited Warranty” which gives you specific legal rights. You may also

have other rights which vary from state to state and province to province.

For a period of two years from the date of purchase, any malfunction caused by
factory defective parts or workm anship will be corrected at no charge t o you. To obtain
a replacement, return the product to the place of purchase.

NOT COVERED: Repair service, adjustment and calibration due to misuse, abuse
or negligence. Unauthorized service or modification of the product or of any furnished
component will void this warranty. This warranty does not include reimbursement for
inconvenience, installation, setup time, loss of use or unauthorized service.

This warranty covers only IQ America products and is not extended to other
equipment and components that a customer uses in conjun ction with our products.

This warranty is expressly in lieu of all other warranties, express or implied,
including any warranty, representation or condition of merchant ability or that the
products are fit for any particular purpose or use, and specifically in lieu of all special,
indirect or incidental or consequential dam age s.

Repair or replacement shall be the sole remedy of the customer and there shall be no
liability on the part of IQ America for any special, indirect, incidental or consequential
damages, including but not limited to any loss of business or profit, whether or not
foreseeable. Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not
apply to you. Retain receipt for warranty

claims.

5080:MANL-WD5080.ed1

(WD5080-ACEPIKEP-N: MANL-WD5080-ACEPIKEP-N.ed4)

WD

I-MANL-IQAPLPWD5080

IQ: IM-WD-5080A(25-11-09)-1

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause
undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Note:This equipment has been tested and found to comply with the limits for a class B digital
device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.

This equipment generat es uses and can radiate radio frequence energy and,if not install ed and
used in accordance with the instructions,may cause harmful interference to radio
communications.However,there is no guarantee that interference will not accor in a particular
installation.if this equipmemt does cause harmful interference to ra dio or television reception, which can
be determined by turning the equipment off and on,the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment a nd receiver.

• Connect the equipment into an autlet on a circuit different from that to which the receiver is
connectec.

• Consult the dealer or an experienced radio/TV technician for help.