IQ-group E-996 Installer's Manual

Chime Receiver

IQ Europe Limited

Sandbeck Lane, Wetherby LS22 7TW.

Visit us at www.iq-europe.co.uk

Installation helpline 0871 717 1100

E-996

V2.0 - 02/05

INSTALLER GUIDE

IQ-DCC-RX-W

SF-DCC-RX.qxd 13/04/2005 13:30 Page 1

MANUFACTURER'S EXTENDED WARRANTY

In addition to your statutory rights relating to this product it is also guaranteed by IQ (Europe)
Limited ("IQ") for 12 months from the date of purchase against faulty materials or workmanship
which affect its designed ability to detect or switch. During this period if the product has a defect
of this nature it will be repaired or replaced free of charge by IQ with the same item, or a similar
one of higher specification, ON CONDITION THAT:-

The buyer takes advantage of any 'return to store' scheme operated by the seller from whom it is
bought.

If the product has a defect outside the period of any seller's 'return to store' scheme it should be
returned to IQ (Europe) Limited at Sandbeck Lane, Wetherby, W. Yorks LS22 7TW, England at
the expense of the buyer together with evidence of the date of purchase (it is the responsibility of
the buyer to prove delivery to IQ).

The product has been bought by the user.
The product has not been misused or handled carelessly, installed incorrectly, or used on a

voltage supply other than that shown on it.
Repairs have not been attempted by anyone other than IQ's staff.
The product has been used for domestic purposes only.
The product has not been installed in any unusually exposed or harsh environmental conditions.
If the buyer is resident in the EU the product or its replacement will be returned to the buyer at

the expense of IQ.
This guarantee excludes liability for discolouration of paint or plastic, or any user replaceable

parts and in particular lamps, glass panels, or globes/lanterns. It does not confer any rights other
than those expressly set out above and does not cover any claims for consequential loss or
damage.
This guarantee is offered as an additional benefit and does not affect your statutory rights as a
consumer.

This contract is subject to the laws of England and Wales.

*** IMPORTANT ***

As of 1 January 2005, changes to the Building Regulations affect domestic electrical installations in

England and Wales. You don't need to be a qualified electrician to make changes to your home's electrical

system, but the work must be done in accordance with the Regulations.

Where you employ an electrician who is a member of a competent person self-certification scheme, they

will be able to certify the work complies with the Regulations.

If you decide to carry out the work yourself we recommend that you make yourself aware of the

Regulations before you begin and if you require any clarification you should contact your Local Authority

Building Control Department.

Details of the Building Regulations can be obtained on the internet via the government website

www.odpm.gov.uk/explanatory-booklet

SF-DCC-RX.qxd 13/04/2005 13:30 Page 2

SECTION ONE

GENERAL INFORMATION

This Chime Receiver must be used in conjunction with suitable IQ Transmitter units in the IQ
Wirefree range.
Upon detection of a signal from a transmitter (bought separately) this Chime Receiver will react
as programmed.

PLEASE NOTE:- PLEASE SEE THE SEPERATE INSTRUCTIONMANUALS FOR THE
TRANSMITTER PRODUCTS TO UNDERSTANDHOW TOPROGRAM ANDADJUST THAT
SPECIFIC TRANSMITTER.
THIS MANUAL COVERS THE INSTALLATION OF THIS SPECIFIC CHIME RECEIVER ONLY

PARTS INCLUDED

- Chime receiver unit

- Instruction manual. Please keep safe for future reference.

TOOLS & PARTS NEEDED

- 3 x 1.5V AAbatteries
The Chime receiver must be used indoors and must be placed within transmission range of the
Floodlight Transmitter. (See later sections for details)

SECTION TWO

CHIME RECEIVER:- INSTALLATION

1. Position your PIR Transmitter (Tx) in desired area, perform walk tests to confirm detection
zones.

2. Position your Chime Receiver (Rx) in desired area up to 100m away (free air space) from the
Tx, take into account the path between the sensor and receiver to ensure range is acceptable as
the range can be reduced by metal objects, walls etc.

Open the battery cover by releasing the catch shown on diagram B and insert 3 x AAbatteries
into the Chime Rx. Ensure polarity is correct. The chime will then scroll through 6 audible sounds
to inform the user of its sound options. There will then be four “beeps” and the flashing LED
indicates that the Rx is ready for Auto programming.
Note:- This will only happen the first time the batteries are inserted into the Chime Receiver.

SECTION THREE

CHIME RECEIVER OPERATION AND TESTING

Auto Programming

Once the PIR Transmitter (TX) and Chime Receiver (RX) are installed, the Receiver needs to learn
the coded signal transmitted from the Transmitter. IQ makes this easy with its Auto Programming
function.

1.Activate the PIR TX by walking into its detection zone
On triggering, the PIR TX will send a signal to the Chime RX
The Chime RX indicates it has received the PIR TX sensor`s unique coded signal by playing a
default “beep”. and the LED continues to flash slowly for 5 minutes. (no other transmitter can
activate the Chime RX unless you program another IQ transmitter to do so.)

2. You have 5 minutes to select an alarm tone. Press the tone/volume button (see fig I) to scroll
through the 6 different alarm tones.

SF-DCC-RX.qxd 13/04/2005 13:30 Page 3