IQ-group E-614, E-616 Installer's Manual

INSTALLER GUIDE

V2 : 04/05

IQ Europe Limited

Sandbeck Lane, Wetherby LS22 7TW.

Visit us at www.iq-europe.co.uk

Installation helpline 0871 717 1100

IQ-73CA180-150-D
IQ-73CA180-300-D

Security Floodlight

E-614 E-616

SF-73CA180-150-D.qxd 16/05/2005 11:20 Page 1

*** IMPORTANT ***

As of 1 January 2005, changes to the Building Regulations affect domestic electrical installations in

England and Wales. You don't need to be a qualified electrician to make changes to your home's electrical

system, but the work must be done in accordance with the Regulations.

Where you employ an electrician who is a member of a competent person self-certification scheme, they

will be able to certify the work complies with the Regulations.

If you decide to carry out the work yourself we recommend that you make yourself aware of the

Regulations before you begin and if you require any clarification you should contact your Local Authority

Building Control Department.

Details of the Building Regulations can be obtained on the internet via the government website

www.odpm.gov.uk/explanatory-booklet

MANUFACTURER'S EXTENDED WARRANTY

In addition to your statutory rights relating to this product it is also guaranteed by IQ (Europe)
Limited ("IQ") for 12 months from the date of purchase against faulty materials or workmanship
which affect its designed ability to detect or switch. During this period if the product has a defect
of this nature it will be repaired or replaced free of charge by IQ with the same item, or a similar
one of higher specification, ON CONDITION THAT:-

The buyer takes advantage of any 'return to store' scheme operated by the seller from whom it is
bought.

If the product has a defect outside the period of any seller's 'return to store' scheme it should be
returned to IQ (Europe) Limited at Sandbeck Lane, Wetherby, W. Yorks LS22 7TW, England
at the expense of the buyer together with evidence of the date of purchase (it is the responsibility
of the buyer to prove delivery to IQ).

The product has been bought by the user.
The product has not been misused or handled carelessly, installed incorrectly, or used on a

voltage supply other than that shown on it.
Repairs have not been attempted by anyone other than IQ's staff.
The product has been used for domestic purposes only.
The product has not been installed in any unusually exposed or harsh environmental conditions.
If the buyer is resident in the EU the product or its replacement will be returned to the buyer at

the expense of IQ.
This guarantee excludes liability for discolouration of paint or plastic, or any user replaceable

parts and in particular lamps, glass panels, or globes/lanterns. It does not confer any rights other
than those expressly set out above and does not cover any claims for consequential loss or
damage.
This guarantee is offered as an additional benefit and does not affect your statutory rights as a
consumer.

This contract is subject to the laws of England and Wales.

SF-73CA180-150-D.qxd 16/05/2005 11:20 Page 2

SECTION ONE

GENERAL INFORMATION

This unit utilises passive infrared technology to detect heat radiation of moving human bodies.
Upon detection, the lamp will illuminate for a user-determined time period.
An integral daylight sensor ensures night-only operation. This unit has a dual light level operation.
During darkness the lamp will illuminate constantly at a user defined light level until it detects
movement, then the unit will switch to full brightness for a user defined time on period.

PARTS INCLUDED

- Luminaire / PIR Sensor unit.

- Instruction manual. Please keep safe for future reference.

- Accessory Pack.

- Tungsten halogen bulb

TOOLS & PARTS NEEDED

- 3 core flexible cable

- Electric/hand-held drill & bits.

- Terminal or Electricians screwdriver

- Large slotted/philips screwdriver

- Wire cutters
Unit is for outdoor use only. Unit is not suitable for portable use.

The unit can get very hot during use. Ensure the unit has cooled before handling.
Ensure adequate ventilation space is allowed between the unit and any object above, in front or
to either side of the unit. Suggested space is 0.5m above, 0.3m to either side & 1.0m in front.
Do not attempt to install during wet weather, if you are suffering from nausea or dizzy spells or on
medication with similar side effects.
If in any doubt, consult a qualified tradesperson or electrician.

SECTION TWO

SELECTING THE LOCATION

The motion detector has a number of detection zones, at various vertical and horizontal angles
as shown (see diagram A).
A moving human body needs to cross/enter one of these zones to activate the sensor. The best
all-round coverage is achieved with the unit mounted at the optimum height of 2.5m.

Careful positioning of the sensor will be required to ensure optimum performance. See diagram A
detailing detection range and direction.

The sensor is more sensitive to movement ACROSS its field of vision than to movement directly
TOWARDS (see diagram B). Therefore position the unit so that the sensor looks ACROSS the
likely approach path.
Avoid positioning the sensor where there are any sources of heat in the detection area (extractor
fans, tumble dryer exhausts etc.) including any other light sources such as other security lighting.
Reflective surfaces (ie pools of water or white-painted walls) and overhanging branches may
cause false activation under extreme conditions.

During extreme weather conditions the motion sensor may exhibit unusual behaviour. This does
not indicate a fault with the sensor. Once normal weather conditions return, the sensor will
resume normal operation.

SF-73CA180-150-D.qxd 16/05/2005 11:20 Page 3

GB

SECTION THREE

INSTALLATION

After choosing a suitable location (see previous section) install the unit as follows:
The unit is suitable for connection to a 240V 50Hz electricity supply. It is suggested that

3-core round flexible cable of 1mm² gauge is used. An internal switch should be installed to
switch the power to the unit ON & OFF. This allows the sensor to be easily switched off when not
required or for maintenance purposes.

Unfasten the screw on the top of the floodlight. Install the halogen bulb, making sure not to touch
the bulb with bare hands. It is suggested that the bulb is handled using a dry cloth.
Ensure the bulb is correctly fitted in the lampholder before use.
Re-attach the floodlight front cover, do not overtighten the fixing screw.

This unit uses an integral wall fixing plate, detach the wall fixing plate by unscrewing but do not
remove the fixing screw on underside of the wall plate (diagram F).

The floodlight is located onto the wall plate by two lugs which are inserted into the rectangular
slots in the top of the wallplate. To remove, loosen but do not remove the fixing screw, and lift the
body of the floodlight upwards to release from the wall plate. (diagram F).

Mark the position of the fixing holes. Ensure wall plate is correctly positioned. Note the orientation
of the wall plate (diagram E).

Drill the holes. Insert wallplugs into the holes.

PIERCE & PASS THE CABLE THROUGH THE GROMMET BEFORE SECURING WALL
PLATE TO WALL.

It is recommended that the grommet is pierced with a screwdriver to ensure a better seal.
Fix the wall plate to the wall (diagram G)
This unit is supplied with a hanging attachment (tether) to aid installation.
If it is not required, simply remove from the unit and discard.
Ensure the tether is securely fixed into the slot before releasing the weight of the unit.
The unit can now be suspended below the wall bracket. (Fig H)

*** IMPORTANT ***

Switch off the electricity at the fuse box by removing the relevant fuse or switching off

the circuit breaker before proceeding with the installation.

SF-73CA180-150-D.qxd 16/05/2005 11:20 Page 4