iQe CS027, CS318, CS317 User Instructions

CS027
User Instructions
Battery Powered 7 Day Programmable
Room Thermostat
Programmable room thermostats are widely recognised as one of the best ways in which to control central heating. The CS027 programmable room thermostat has a large display and intuitive user interface, making it easy to set up and use. The CS027 uses a sophisticated time proportional integral (TPI) algorithm for accurate temperature control and energy efficiency.
1
What is a programmable room thermostat?
...an explanation for householders.
A programmable room thermostat is both a programmer and a room thermostat. A programmer allows you to set 'ON and OFF' time periods to suit your own lifestyle. A room thermostat works by sensing the air temperature, switching on the heating when the air temperature falls below the thermostat setting and switching it off once the set temperature has been reached.
So, a programmable room thermostat lets you choose what times you want the heating to be on, and what temperature it should reach while it is on. It will allow you to select different temperatures in your home at different times of the day (and days of the week) to meet your particular needs.
Turning a programmable room thermostat to a higher setting will not make the room heat up any faster. How quickly the room heats up depends on the design of the heating system, for example, the size of the boiler and radiators. Neither does the setting affect how quickly the room cools down. Turning a programmable room thermostat to a lower setting will result in the room being controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to find the lowest temperature settings that you are comfortable with at the different times you have chosen, and then leave it alone to do its job. The best way to do this is to set low temperatures first, say 18ºC and then turn them up by one degree each day until you are comfortable with the temperatures. You won't have to adjust the thermostat further. Any adjustments above these settings will waste energy and cost you more money.
2
If your heating system is a boiler with radiators, there will usually be only one programmable room thermostat to control the whole house. But you can have different temperatures in individual rooms by installing thermostatic radiator valves (TRVs) on individual radiators. If you don't have TRVs, you should choose a temperature that is reasonable for the whole house. If you do have TRVs, you can chose a slightly higher setting to make sure that even the coldest room is comfortable, then prevent any overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be adjusted in spring and autumn at the changes between Greenwich Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for example, 'Override', 'Advance' or 'Boost'. These are explained in the manufacturer's instructions.
Programmable room thermostats need a free flow of air to sense the temperature, so they must not be covered by curtains or blocked by furniture. Nearby electric fires, televisions, wall or table lamps may prevent the thermostat from working properly.
3
Actual Room Temperature
Day of Week
Time of Day
Until (Time)
Then (Temp)
Enter Button
+ Button- ButtonBack
Button
Set Temperature
4
DISPLAY
CS027
DISPLAY
Actual Room Temperature This is the actual room temperature
measured by the CS027
Set Temperature This is the temperature that the CS027
will allow the room to reach. The temperature range can be set between 5°C and 30°C
When the temperature shown in the display is achieved the CS027 will switch the heating OFF.
If the temperature in the room falls below the setting the CS027 will switch the heating ON.
Until (time) This is the time that the next
temperature setting is due to operate
Then (temp) This is the temperature setting that is
due to operate next
Day of the week It is important that the correct day of the
week shows in the display
Time of day This is the current time of day
Setting Buttons Press any button to illuminate the
display.
The message 'To override press -/+ To see menu press ENTER' will appear
ACTIVATING THE BACK-LIT DISPLAY
Press any button to illuminate the display. This will remain illuminated for 10 seconds
GENERAL INFORMATION
During programming please note that the display will return to its normal operating screen if the last button press exceeds 10 seconds.
5
TEMPORARY OVERRIDE
A temporary temperature change can be made at any time. It is also possible to extend how long this temperature override is in operation.
The temperature will revert to its normal programmed setting at the next timed temperature change
TEMPORARY OVERRIDE WITH TIME EXTENSION (Maximum of 4 hours)
The temperature will revert to its normal programmed setting at the next timed temperature change.
Press ‘-’ or ‘+’ to adjust temperature
New temperature setting will be shown on the display
Press ‘-’ or ‘+’ to adjust temperature
New temperature setting will be shown on the display
Press ENTER
Press ‘+’ to adjust the time
Press ENTER
6
The hours of the UNTIL time will flash
PERMANENT OVERRIDE
In the 'HOLD' position the temperature can be overridden by pressing either the '-' or '+' buttons. This will then become the new 'HOLD' temperature
PERMANENT OVERRIDE – CANCELLATION
Press ‘-’ or ‘+’ to adjust temperature
New temperature setting will be shown on the display
Press ENTER
The hours of the UNTIL time will flash
Press ENTER
Press the '+' repeatedly until HOLD appears in the display
Message will appear briefly confirming 'Temperature set until manual release'
Press BACK
Press ENTER
7
SETTING UP THE CS027
Upon initial installation the CS027 has the following factory default settings
Settings – Monday to Friday
Time Target Temperature
Period 1 06:00 am 20 °C
Period 2 08:30 am 18 °C
Period 3 11:30 am 20 °C
Period 4 01:30 pm 18 °C
Period 5 05:00 pm 21 °C
Period 6 10:00 pm 15 °C
Settings – Saturday and Sunday
Time Target Temperature
Period 1 07:00 am 20 °C
Period 2 10:00 am 19 °C
Period 3 11:30 am 21 °C
Period 4 01:30 pm 18 °C
Period 5 05:00 pm 21 °C
Period 6 11:00 pm 15 °C
These can be changed by the installer or the end user at any time by accessing the MAIN MENU
8
MAIN MENU
To access the MAIN MENU take the following steps:
MENU OPTIONS
Press ENTER twice
Press '-' or '+' to toggle between the menu options
Programme This allows the user to adjust the different
time and temperature settings from the factory default settings shown in the table on page 8.
Up to six different temperature levels can be
set in any 24 hour period
Standby This puts the CS027 into Frost protection or
Standby condition and allows the heating to be permanently switched off but will activate and switch the heating on if the temperature in the house falls below the standby temperature set.
All programme settings are overridden and
the unit will not return to normal operation until the standby period has ended by pressing the ENTER button.
Holiday This puts the CS027 into a temporary
standby mode with a start and end date which can be set to coincide with a holiday period. At the end of the set period the CS027 will resume normal operation
Time / Date The CS027 has a built in clock and
calendar. This will require setting on initial installation. If this has not been set on installation please go to Setting the TIME and DATE section on page 14 before continuing
Set Up Enables the programming of various options
outlined in the SET UP MENU on page 15 of these instructions – These should be set on installation.
9
Setting the PROGRAMME
Six time and temperature settings are available in each 24 hour period. Pressing BACK at any time in this process will return you to normal operating mode.
If only two different temperature settings are required in 24 hours then set the first time and temperature using programme one (P1) and the second time and temperature setting using programme setting two (P2). The remaining programmes (P3 to P6) should all be set to the same time and temperature as P2.
This same method can be used if three, four or five temperature levels are required, always using the first settings to provide the temperature change commands with the remaining settings that are not required set to the same time and temperature as the last required setting.
Press ENTER three times
The day of the week will flash
Press '-' or '+'
to select day to
programme
Press ENTER
Press ENTER
Time / Temperature setting P1 will flash
Press '-' or '+' to select time / temperature period you wish to set (P1 to P6)
Temperature will flash, use the '-' or '+' to select the required temperature
Press ENTER
The hours START time will flash
Press '-' or '+' to adjust the hours then press ENTER. The minutes will then flash.
Press '-' or '+' to adjust the minutes then press ENTER.
If you require to set further periods for the same day, the next period will now automatically flash. Follow this process again to programme as required
10
On completion of period 6 (P6) go to the copy process on Page 11 of this booklet
To copy the same programmes to other days of the week, please follow the process below
Setting the STANDBY
To exit STANDBY mode, press ENTER TWICE
When you have set P6 the message 'To Copy press ENTER' will appear.
Press '-' or '+' to select the days you wish to copy the set programmes. Pressing ENTER after each day to confirm
The next sequential day will now flash.
When complete press BACK to return to normal operating mode
Press ENTER
To programme remaining days please go to the start of the process 'Setting the PROGRAMME'
Press ENTER Twice
The words STANDBY and Standby Enabled will appear on the display
Press ENTER
After a short period Standby Enabled will disappear from the display
Press '-' or '+' until STANDBY appears on the display
11
Setting the HOLIDAY programme
Pressing BACK at any time in this process will return you to normal operating mode
Press ENTER twice
The START date will now flash
Press ENTER
Press the '-' or '+' to adjust to the date you wish the holiday programme to start. Pressing ENTER to change between Day, Month and Year
Press '-' or '+' until
HOLIDAY appears
on the display
The BACK date will now flash
Again, Press the '-' or '+' to adjust to the date you wish the holiday programme to end. Pressing ENTER to change between Day, Month and Year
12
HOLIDAY programme is now set
If the holiday period START date matches today's date, the STANDBY temperature will be shown on the display together with the suitcase icon.
If the holiday period START date does not match today's date the display will remain in normal operating mode but with the suitcase icon appearing on the right of the display. Indicating a holiday period is pending
To cancel a set holiday programme in ADVANCE of its activation, re-programme using the above procedure and set the START date and BACK date to today's date.
To cancel a set holiday programme during activation press ENTER button twice, the unit will return to normal operating mode and the suitcase icon will disappear.
THE DATES SPECIFIED BECOME EFFECTIVE FROM MIDNIGHT OF THE DAY ENTERED
13
Setting the TIME and DATE
Pressing BACK at any time in this process will return you to normal operating mode
If an incorrect date is entered the wrong day will appear in the normal operating screen.
Press ENTER twice
The hours for the time of day will flash
Press ENTER
Press '-' or '+' to adjust hours then press ENTER
Press '-' or '+' until
Time/Date appears
on the display
The minutes for the time of day will flash
Press '-' or '+' to adjust minutes then press ENTER
The day of the date will now flash
Press '-' or '+' to adjust the day to match today's date Pressing ENTER to change between Day, Month and Year
Time and Date are both set and the unit will return to normal operating mode
14
SETUP MENU
To access the SET UP MENU take the following steps:
MENU OPTIONS
Press ENTER twice
Press ENTER
Press '-' or '+' to toggle between the menu options detailed below
Press '-' or '+' until Set Up appears on the display
Select clock format This allows the display to show the time in
24 hour or AM/PM format
Daylight saving This is the adjustment made in the UK when
the clocks go back or forward in the Autumn and Spring.
When using the CS027 in the UK the
daylight saving ON setting should be selected which will automatically adjust the GMT/BST times accordingly
Standby temperature This is the temperature setting used when in
Standby or Holiday mode (Min 5°C / Max 30°C)
In cold weather the heating will activate if
the temperature being measured falls below this temperature setting.
Lower temperature limit This sets the lowest temperature setting the
CS027 will allow to be programmed.
The default setting is 5°C
Upper temperature limit This sets the highest temperature setting
the CS027 will allow to be programmed
The default setting is 30°C
15
TPI cycles per hour This setting helps the TPI energy saving
software to operate correctly depending on the type of heating system you have
Optimum start This calculates the amount of time the
CS027 may need to switch on in advance of the next target temperature setting in order to meet the requirement.
Tamper setting This setting allows a 4 digit release code to
be set up to stop unauthorised adjustments being made in multi occupancy buildings.
MENU OPTIONS (Contd...)
Setting the SELECT CLOCK FORMAT
Pressing BACK at any time in the process will return you to normal operating mode
Press ENTER twice
Press ENTER
Press '-' or '+' until Select clock format appears on the display
Press '-' or '+' until Set Up appears on the display
Press ENTER
Either 'Select clock 24 hr' or 'Select clock AM/PM' will appear
Press '-' or '+' to toggle between the two options
Select your choice by pressing ENTER
The unit will now return to the Set up position, simply press BACK to return to normal operating mode
16
Select the DAYLIGHT SAVING
Pressing BACK at any time in this process will return you to normal operating mode
The default factory setting is for the Daylight saving to be ON giving automatic switching to GMT/BST
Press ENTER twice
Press ENTER
Press '-' or '+' until Daylight saving appears on the display
Press '-' or '+' until Set Up appears on the display
Press ENTER
Either 'Daylight Saving Off' or 'Daylight Saving On' will appear on the display
Press '-' or '+' to toggle between the two options
Select your choice by pressing ENTER
The unit will now return to the Set up position, simply press BACK to return to normal operating mode
17
Setting the STA N DBY TE M PERAT U RE, LOWER TEMPERATURE LIMIT or UPPER TEMPERATURE LIMIT
Pressing BACK at any time in this process will return you to normal operating mode
Press ENTER twice
Press ENTER
Press '-' or '+' until the required option appears on the display
Press '-' or '+' until Set Up appears on the display
Press ENTER
The temperature setting will now flash
Press '-' or '+' to adjust temperature then press ENTER
The unit will now return to the Set Up position, simply press BACK to return to normal operating mode
18
Setting the TPI cycles
Pressing the BACK at any time in this process will return you to normal operating mode
Oil Boilers 3 cycles per hour
Gas Boilers 6 cycles per hour
Not used 9 cycles per hour
Electric Heating 12 cycles per hour
This feature would normally be set by your installer
Press ENTER twice
Press ENTER
Press '-' or '+' until TPI Cycles per hour appears on the display
Press '-' or '+' until Set Up appears on the display
Press ENTER
The current setting will now flash
Press '-' or '+' to adjust to the correct setting for your heating system. (Please refer to table below)
The unit will now return to the Set Up position, simply press BACK to return to normal operating mode
Press ENTER
19
Setting the OPTIMUM START
This setting will allow the CS027 to anticipate the next set temperature and switch on up to two hours in advance to ensure room temperature has been reached by the time the new set temperature applies.
As a consequence the switch on time could take place anywhere between 2 hours and zero before the set time and temperature.
With the optimum start set to OFF the user will need to anticipate the warm up time needed in the programme settings. (Typically the set temperature will be set approx. 1 hour in advance of when it is required)
Pressing the BACK at any time in this process will return you to normal operating mode
This feature would normally be set by your installer.
Press ENTER twice
Press ENTER
Press '-' or '+' until Optimum Start appears on the display
Press '-' or '+' until Set Up appears on the display
Select YES or NO and press ENTER to confirm
20
Setting the TAMPER SETTING
This setting allows the unit to be locked to the programmes set and can only be reactivated by entering the pin code.
None of the buttons will operate until the security code is entered
Pressing BACK at any time in this process will return you to normal operating mode
21
Press ENTER twice
Press ENTER
Press '-' or '+' until Tamper Setting appears on the display
Press '-' or '+' until Set Up appears on the display
The first digit of FOUR will now flash
Press ENTER
Press '-' or '+' to adjust to a number of your choice (0-9), then press ENTER
PLEASE MAKE A NOTE OF THIS CODE AND KEEP IN A SAFE PLACE. THIS WILL BE REQUIRED TO MAKE ANY CHANGES IN THE FUTURE
A message will appear briefly confirming 'Tamper code set when this message clears'
Repeat the previous step for the second, third and fourth digits
Cancelling the TAMPER SETTING
Pressing BACK at any time in this process will return you to normal operating mode
If you do not know the release code, contact the Homeowner or Landlord in the first instance.
Press ENTER twice
Press ENTER
The following message will appear 'Enter first digit'
The following message will appear 'To enter release code press ENTER'
Repeat the previous step for the second, third and fourth digits
Press '-' or '+' to confirm the first digit of the release code, then press ENTER
The following message will appear 'Tamper Code Cleared'
22
RESETTING THE CS027
Electronic equipment can in some circumstances be affected by electrical interference.
If the display becomes frozen or scrambled simply press both the BACK and ENTER button simultaneously.
Using this proceure will restore the CS027 to the original factory settings, the Time and Date will remain correct.
BATTERY
The CS027 runs on 2 standard AA (Alkaline) non rechargeable batteries and is designed to give a battery life of approximately two years.
There are three stages of warning as the batteries become low in power.
BACK ENTER
23
Stage 1 – The battery low symbol will appear in the display
Stage 2 – The words 'Low Battery' will appear in the display for 1 second each time a button is operated
Stage 3 – The unit will switch itself OFF and the message 'Replace Batteries' will appear permanently in the display.
The batteries should be changed at Stage 2 at the latest.
To replace the batteries of the CS027, please carefully pull down the hinged battery cover on the front of the unit. Ensure they are fitted correctly as indicated by the terminal markings in the battery compartment.
Please dispose the old batteries responsibly
SERVICE AND REPAIR
This programmer is NOT user serviceable. Please do not dismantle the unit. In the unlikely event of a fault developing please refer to the RESETTING THE CS027 on page 23. If this fails to resolve the problem please contact a local heating engineer or a qualified electrician.
24
www.iQE.co.uk Trade House BA22 8RT
Part Number P85553 Issue 2
Loading...