Page 1
Model TapeShooter® 404
Tape Dispenser
TapeShooter
®
BP P/N: TS404-OPR File Name: TS404 Operating Manual-27Apr05
404 OPERATING MANUAL
Page 2
2
Page 3
This manual is a non-controlled document
Information in this manual does not constitute a warranty of performance.
Furthermore Better Packages reserves the right to revise this publication and
make changes from time to time, in its content.
Better Packages ASSUMES NO LIABILITY WHAT SO EVER FOR ANY
LOSSES OR DAMAGES INCURRED AS A RESULT OF INFORMATION
CONTAINED IN THIS MANUAL.
Proprietary Notice
This publication contains information proprietary to Better Packages. Any
reproduction, disclosure, or use of this publication is expressly prohibited except
as Better Packages may otherwise authorize in writing.
Better Packages, Inc.
3
Page 4
TECHNICAL DATA
Size: 14” L x 5” W x 7” H
Tape Type: Plain Kraft Gummed Out Tape
Tape Width: 1” – 1 ½ “
Maximum Roll Size: 5 “ or 500’
Cutting Mechanism: Guillotine Cutting Blade
Maximum Carton Weight: 35 Pounds
Shipping Weight: 7 lbs.
All specifications subject to change without notice.
UNPACKING
When unpacking your new Better Packages TapeShooter® 404 Dispenser,
check to make sure you have the following items before discarding the carton
and packing material.
• Operating Manual
• Water tank
• One Brush
• Two Tape Guides
• Tape Plate
4
Page 5
PREPARING THE MACHINE FOR OPERATION
Once the unit has been removed from the carton and all items are accounted for,
you may begin using your TS404 Dispenser.
1. Raise Cover and adjust tape guides to your desired tape width.
2. Place roll of tape between guides with tape lead facing the front of the
dispenser.
3. Remove the water tank by lifting it upwards. Lift and remove the brush.
Rinse the brush with warm soapy water for best results. This helps insure
proper performance. Replace brush in the tank and fill water tank
reservoir with warm water. Replace lid and return to position in dispenser.
Adjustable
Guides
Tape Lead
Tape Guides
Remove Tank
Brush
Lid
5
Page 6
4. Feed stop screw can be loosened to adjust the measuring dial to
necessary length. Upon proper adjustment, tighten feed stop screw.
Adjustable Feed
Stop Screw
5. Once tape is properly loaded and the brush and water tank are in place,
you are ready to dispense the tape. With the adjustable feed stop set at
your desired length, simply pull the handle downward and the tape will be
dispensed and cut.
Pull handle forward to
dispense and cut tape
MAINTENANCE
Simple care is required to guarantee quality sealing with your model TS404
Dispenser.
1. Keep brush and water tank clean. Rinse brush and tank in warm soapy
water frequently.
2. Clean knife blade if it becomes coated with adhesive or dirt.
3. For a good appearance and operation, the outside of the dispenser should
be cleaned from time to time using only a mild solution of soap and water.
Never use detergents or abrasives of any kind. Wipe with a clean
cloth.
6
Page 7
Better Packages, Inc.
Warranty Information
Limited Warranty Statement
The manufacturer warrants each new Better Packages machine and accessory to be free from defects in material and
workmanship under normal and proper use, its obligation under this warranty being limited to replacing or repairing
any defective parts within the time period indicated for the specific model after delivery (at the company’s
discretion) to the customer. Wearable parts such as shear blades, springs, water brushes and motor brushes are not
covered under the warranty. Machines used for any reason not intended by the manufacturer will not be considered
for warranty protection.
The company will replace or repair (at the company’s discretion) any defective parts within the warranty period, on
a no-charge basis. The Authorized Distributor/Service Center will furnish, without charge, within the time period
indicated for the specific model, necessary labor to service the machine.
If customer wishes, they may forward their machine (excluding case sealers) with authorization to Better Packages
or an Authorized Distributor/Service Center for warranty service. Any item shipped for warranty service must be
shipped in the original factory carton and properly packed with the original protective packaging inserts or a secure
carton that will properly protect the unit during transit. Units received improperly packed are subject to costs
associated with damage caused during transit. These costs will be the responsibility of the customer. All associated
shipping or freight costs related to items shipped for service are the sole responsibility of the customer.
For service under this warranty, call or write your nearest Better Packages Distributor/Service Center or Better
Packages, Inc. Shelton, CT at 800-237-9151. Transportation charges on machines or parts returned to Better
Packages for service must be prepaid by the customer. Customers will be responsible for freight expenses on parts
or machines returned to them.
Product Warranty*
Model Parts Labor
Better Pack® 755 Series 2 Years 6 Months
Better Pack® 754 Series 2 Years 6 Months
Better Pack® 555e series 2 Years 6 Months
Better Pack
BP Sealmaster 3000 CS &
®
500 series 2 Years 6 Months
1 Year 6 Months
3000 AFF
Better Pack® 333 Series 2 Years 6 Months
TapeShooter® 150 2 Years 6 Months
TapeShooter® 404 2 Years 6 Months
Packer® 3S 2 Years 6 Months
Better Pack® PS2A 1 Year 6 Months
*When servicing a Better Packages product, genuine Better Packages replacement parts
should be used. Any other parts used will void all existing warranties and any UL, CE and
CSA certifications and may create a safety hazard.
Visit www.betterpackages.com to locate your local Authorized Distributor/Service Center
This warranty statement dated January 1, 2007 supersedes all other prior published statements.
7
Loading...