IP Power 9858S S+Ping, 9858T T+Ping User Manual
Firmware Version: 1.0B
Date Released: SEP. 2014
IP Power 9858S / S+Ping
9858T / T+Ping
User Manual
- 1 -
Warning: Any changes made to this equipment without permission may cause damages to the device!
IMPORTANT NOTICE
1. IP Power 9858 was designed for indoor use, we carry no responsibility for possible damages
caused by outdoor use, especially in the rain.
2. Please use the power adapter provided by the dealer, we carry no responsibility for the
possible damage from using power adapters not provided by us .
4. Do not shake the IP Power 9858 in any fashion
5. Please contact the dealer If IP Power 9858 is not working properly.
Copyright © 2014 All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording or otherwise, without the prior written consent of us.
All trademarks and products mentioned in this document are the properties of us.
- 2 -
Table of Content
WELCOME ........................................................................................................... 5
Introduction .................................................................................................................................................. 5
Features : ....................................................................................................................................................... 6
Specification .................................................................................................................................................. 6
Minimum System Requirements ................................................................................................................. 6
Package Contents ......................................................................................................................................... 7
INTERFACE DESCRIPTION ................................................................................ 8
Front View..................................................................................................................................................... 8
Rear View ...................................................................................................................................................... 9
Fuse replacement .........................................................................................................................................10
SETTING UP YOUR DEVICE ............................................................................. 11
Before Starting .............................................................................................................................................11
Hardware Connection .................................................................................................................................11
Software Installation ...................................................................................................................................11
Installing Software ....................................................................................................................................11
Connection by WiFi- WPS ( WiFi Protection Service ) ...........................................................................13
Connecting first by LAN –Network cable then setup for WiFi connection ..............................................16
Internet Setup ................................ ................................ ................................................................ ............21
Using IP Server .........................................................................................................................................21
WEB INTERFACE .............................................................................................. 23
Connect to your Device ..............................................................................................................................23
Device name .............................................................................................................................................25
Information : .............................................................................................................................................26
IO Control : ...............................................................................................................................................26
Network : ..................................................................................................................................................36
Application Settings..................................................................................................................................47
System Setting ..........................................................................................................................................50
CONTROLLING THE DEVICE ........................................................................... 59
CGI HTTP Commands .............................................................................................................................59
Telnet Control ..............................................................................................................................................60
- 3 -
FAQ : .................................................................................................................. 61
- 4 -
Welcome
Introduction
IP Power 9858 is a new generation of the Power Distribution Unit (PDU) & Remote Power
Control (RPC) system. Its able to connect to the WiFi network plus WPS function for easy &
quick set up a device to user’s wireless home/office network and control in the network
With embedded web server and HTTPS protection , 9858 supports higher grade security as
working on Internet. User can control power easily and more safely through the web browser on
Windows PC or on Smartphone like Internet Explorer (IE) , Firefox , Google
Chrome , Safari ( iOS ) and Android system.
9858 allows user to remote control power up to 4 separate devices on/off via network . As
support SSL & SNMP, user can use public email like Gmail / Hotmail / Yahoo Mail to get the
email as the ON/OFF status change . User can also control by e-mail without doing port
forwarding / port mapping and search the other IP Device in webpage directly .
Besides control through web browser , there is Android Apps name “IP Power “ for Android
user to control the outlet power turn ON / OFF and quick search device in LAN / WAN Android
phone / touch panel . No PC system environment or emergency use for quick response in
second.
Not only control manually, 9858 supports Auto Ping ( 9258S+Ping & 9258T+.Ping only ) ,
Time Scheduler which is more suitable for factory / commercial / office / home automation .
There is LOG information & send LOG to assign IP (SYSLOG ) in webpage.
For system integrator, there are several popular developing tolls like TelNet and HTTP
Command ( SDK) for 2nd development .
The various applications of the 9858 includes:
Power Management, Server Management, Internet Controllable Timer,
System Integration, Remote Power Control in Remote locations ………….. etc.
User Friendly . Convenience & Powerful ,
- 5 -
Product Overview
Features :
1. 4 port Remote power controller for power On, Off and Reboot.
2. Web Server built-in design, directly control by web browser – PC & Smartphone
Internet Explore (IE) , Firefox , Google Chrome , Safari - iPhone and Android
browser of Smartphone. ( Windows , Android & iOS) .
3. Android Apps “IP Power “ – free download
- Controls the outlet power ON/OFF without doing Port Forwarding / Port Mapping
- Quick search in LAN / WAN ( like IPEDIT & IP Service )
4. Support WiFi - Wireless 802.11 N/ B/ G and WPS connection
( WPA-PSK, WPA2-PSK, AES,128-bit WEP,64-bit WEP,TKIP, WPA2,WPA )
5. Support HTTPS , SSL , TCP/ IP , PPPOE, DHCP, DDNS , SMTP & Telnet.
6. Power Surge protection & FUSE embedded in.
7. LOG : Support Log function .
8. Time Schedule - can pre-set a suitable time to turn power on / off automatically .
9. Auto Ping for network control & segment management automatically (( 9858S+Ping
& 9858T+.Ping only )
10. Back Up for quick setup for multiple devices like Time Schedule, Network Setting.
11. Support public e-mail -- @gmail.com , @yahoo.com , @hotmail. com ..........etc.
12. E-mail Control & Advice as device boot up.
13. Specific software developed by Aviosys and provided free of charge :
- SDK Available : HTTP Command & Language
- IP Power Center - for control multiple Aviosys IP devices in same software
- CNT software ( Cross Network Technology )- allows user eliminate set up work on
any Router without port forwarding , simply Plug & Play .
Specification
Power input : 100V - 240V
Maximum loading of each output: 8 amp
Maximum of Total loading : 8 amp
Fuse protection : 10 amp ( with spare fuse in socket )
Dimensions: 200 x 140 x 50 mm ( L x W x H )
Weight: 990g
Enclosure – Matel case in Gray color
Minimum System Requirements
Windows PC OS with network capacity.
Browser : Google Chrome , Safari , IE 9.0 or above .
RJ45 LAN & Internet HUB / Switch
Internet ( for remote access) or Ethernet Network ( Internal Network use) with some type of
Internet connection, (i.e. ADSL, Cable, Dial up or any other forms of Internet service)
- 6 -
Package Contents
1. 9858 Unit x 1
2. 9858 Installation CD
3. Power IN Cable (option)
Please double check the power cable compatible
for 10 amp current loading .
- 7 -
Interface Description
From Left to right :
Power Status Indicator:
The Power Status #1 ~ #4 Indicator - Green
light ON as output power ON.
Reset :
Set back to default setting by long press
To reset to original manufacture settings, hold
down the reset button with a sharpen pin for
5- 6 seconds then RELEASE. There are 3
beeps sound which means reset start and
9858 will be rebooted itself -there is one beep
after reboot ) and most information go back to
default setting ( LAN IP ).
WPS :
Enable WPS function by one short click
function. Please refer page #13 for details.
Link:
The Link Indicator shows the WiFi signal
transfer status. The light will be ON all the time
and flashing while transfer data.
Network: LAN
LAN 10/100 Mbps network
Network :WIFI
WIFI 802.11N-B/G
Front View
- 8 -
Rear View
From Left to right :
4 Output Power Ports:
9858-T ( Upper picture )
9858-S ( Down picture )
There are 2 models outlet :
* 9858-T : NEMA
* 9858-S : IEC320
Connect up to 4 separate devices
that will be controlled by the 9858.
Ports 1 - 4
1 Input Power Port :
In this socket, there is power input
and Fuse socket .
The input power sends power
to the 9858.
Fuse : To prevent electrical
surges from damaging the unit.
The 9858 comes with one
spare fuse in the unit.
TYPE：U/C GFE 10A 250V (PF)
1 Power Switch:
The Power switch turns on the
input power.
- 9 -
Fuse replacement
1.) The fuse is located between the power switch and the power input plugs.
2.) Carefully remove the fuse holder with a flat screwdriver.
3.) The fuse can be purchased from electronic shops.
Specification : U/C GFE 10A 250V (PF)
- 10 -
Setting up your device
Before Starting
*Before setting up the device make sure of the following:
1.) All the package contents are all included if anything is missing please contact the dealer
where the device was purchased from.
2.) Check the power input cable is working correctly.
3.) Check all cables to make sure there are no problems with it.
Hardware Connection
Please refer following procedure :
1.) Connect the Ethernet cable (RJ45) to the 9858 to your local area network.
2.) Then connect the power cable into the power input port of the 9858.
3.) Connect the device that you would like to control to the output plug on the top of the 9858.
4.) Switching the power source to ON status , this switch is located at the rear of 9858.
5.) After power on for around 45 seconds , there is a short beep sound for 9858 which means
the system reboot successfully
6. ) Go to page #14 for software installation guide – use IP EDIT to log in the webpage of
9858.
Note: To change the network setting for WiFi connection ( if your Router without WPS function ) ,
please go to page # 12 to setup the WiFi connection manually .
Software Installation
The Media Link - IP Family CD comes with the device , it has all the necessary software to run
and setup the device.
IP Power Software:
IP Edit ( Required)
IP Power Center *( For multiple IP Power devices control purpose )
Installing Software
1.) Place the Media Link-IP Family CD into the CD/DVD Rom drive.
(The CD will auto run , but if it does not go to the CD/DVD Rom drive and select the
“autorun.html” file.)
- 11 -
2.) Click on the IP Power Section Bar
3.) Select the IP Power 9858
4.) All the available downloads for the 9858 will be shown
- 12 -
`
5.) Download the required software – IPEdit.exe - by clicking on the download button.
Then you can select to connect 9858 by LAN or by WAN ( WPS)
Connection by WiFi- WPS ( WiFi Protection Service )
IP Power 9858 has WPS function , which can assist user setup the WiFi connection from user`s
router and IP Power 9858 automatically & fast . Before using WPS function, please check your
WiFi router and see if there has WPS function first . There should have a button name “WPS /
QCC “ or a sign on the router for user to click easily.
Please refer following steps to setup WiFi –WPS connection
Step 1: Power on the 9858 - only connect power in but do not connect the LAN cable , you will
hear one short beep in 40 seconds means 9858 boot successfully
Step 2: Press the “WPS button” of your WiFi Router. ( Please check your router WPS function )
- 13 -
Step 3 : One short press on the “ WPS ” button of 9858 and then there is one long beep
sound which means the WPS function of 9858 is enabled .
Step 4: After few seconds , there are 2 short beep Which means WPS connection
successfully ( If WPS connection fail , there is one long beep sound mean the connection fail.
Please go back to step 2 and try again )
WPS Quick procedure :
One short press “ WPS “ button on 9858 One Short beep 5-10 seconds short 2
beeps WPS connection successful
Step 5 : Execute IPEDIT.exe . There is WiFi IP address of 9858 shown in IPEDIT.exe as
following : Device name in local devices area is “ IP POWER (w)
- 14 -
If can’t see the IP in the area of Local Devices of IPEDIT.exe. Please disable the Firewall
and Anti Virus software temporally and try again .
Step 7 : Double click the IP address and your PC will execute web browser like IE ,Firefox or
Google Chrome and there is wizard pop up to enquire the Username and Password .
Username : admin Password : 12345678
Step 8 : For the WiFi connection by WPS way , user can check here :
Network WiFi Info Profile list
To make this WiFi IP Address can be found on Internet, please arrange 2 settings as log in the
9858 webpage:
1st : Go to “ Network Setting Default Network Type ( gateway) Setting “ and change as
WiFi for the Default Network Type ( gateway) Setting .
- 15 -
2nd : Do the Port Mapping / Port Forwarding in your router ( Need to check the router owner’s
manual ).
Connecting first by LAN –Network cable then setup for WiFi connection
Without WPS , user can use LAN network cable to connect 9858 first .
LAN connect by IP Search software “ IPEDIT “
IP Edit is a search tool designed to search, configure, or access the IP Power 9858 from a local
networked computer.
IP Power 9858 Default Login / Password
Default IP: 192.168.1.168 (While this is no DHCP apparently)
Default Login: admin
Default Password: 12345678
1.) In the local devices section user will see user device show up if connection correctly.
- 16 -
If can’t see the IP in the area of Local Devices of IPEDIT.exe. Please disable the Firewall
and Anti Virus software temporally and try again.
2.) Select the 9858 device and the device information will pop up on the right.
3.) Check to see that the gateway IP and the IP Address (9858) match user current network.
If not, type in the correct information, then hit the submit button to save changes.
For example:
If user have the following information regarding the 9858 and user network
User PC Network :
Computer IP Address: 192.168.1.122
Gateway: 192.168.1.1
Sub Net mask: 255.255.255.0
Port: 80
User 9858 in IPEDIT :
9858 IP Address: 192.168.100.34
Gateway: 192.168.100.1
Sub Net mask: 255.255.0.0
Port: 80
Since the IP Address of the 9858 is : 192.168.100.34
User will need to make sure that the first 3 segments of user 9858 IP Address
must match the first 3 segments of user gateway IP.
First 3 Segment of Gateway Address: 192.168.1.X
So user new IP Address for the 9858 should be: 192.168.1.XXX
New Network Information
9858 IP Address: 192.168.1.26
Gateway Address: 192.168.1.1
Local Computer IP Address: 192.168.1.122
Sub Net mask: 255.255.255.0
Port: 80
4.) Press the “ Rescan “ button to see if changes have been made.
5.) Double click on the device in the local device section and an IE web browser
with the device login will pop up.
6.) Type in the default Login and IP Address to enter the device.
Default Login : admin
Default : 12345678
Notice :
* User can click " REF " in IEPDIT to auto search proper IP setting for 9858.
It will take few minutes to show the suggest wizard.
- 17 -
Please click “ APPLY “ as seeing the suggest wizard , click " yes " to ignore the remind message
of IP being used and then type the Username and Password to change the IP setting.
Username : admin
Password : 12345678
Notice :
# Segment : The first 9 digits of the IP Address .
EX: The IP of user PC is 192.168.100.122. If the “ Local IP Address “ at WiFi Info is 192.168.100.
x ( X can the value of 1~252 ) , user PC can get into the webpage of 9858 .
# Please press “Rescan “ to search the router near by again if can not see user router in the list.
WiFi Connection after log in webpage by LAN :
After log in 9858 , to connect by WiFi , please go to Network WiFi Survey to add the WiFi
router in to 9858 WiFi profile .
- 18 -
1) As go to WiFi Survey page, there is a list for the available WiFi router near 9858 . Please
select the one plan to use and click “ Add Profile “
9858 will get most information from user’s router automatically and user just need to type the
password to connect with the WiFi router then click “ Apply “
Then user can get the router information in “ Profile list “ section as following pictures
- 19 -
Loading...