IPOX Tech IP-4GVI83 User Manual

P4BGB

Series

(Industrial Board)

INSTALLATION GUIDE

Installation Guide Revision A0

COPYRIGHT

©

All rights reserved. The information contained in this guide has been
validated and reviewed for accuracy. No patent liability is assumed with
respect to the use of the information contained herein. While every
precaution has been taken in the preparation of this guide, the Manufacturer
assumes no responsibility for errors or omissions.

No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permi ssion of
Manufacturer.

TRADEMARK™

®

Intel

, Pentium® and Celeron® are registered trademarks of Intel®

Corporation.
Microsoft

®

and Windows® are registered trademarks of Microsoft

Corporation.
All products and company names are trademarks or registered trademarks

of their respective holders.
These specifications are subject to change without notice.

Installation Guide Revision A0

June 2004

i

CONTENTS

ECTION 1 INTRODUCTION 1

S

1.1 Unpacking P4BGB Series 1

1.2 Description 2

1.3 Features 2

1.3.1 Graphic & Ethernet 2

1.3.2 Ultra ATA/66/100 3

1.3.3 Hardware Monitoring 3

1.3.4 I/O Shield Connector 3

1.3.5 Power-On/Off 4

1.3.6 P4BGB Series Overview 4

1.3.7 System Block Diagram 5

1.4 Specifications 6

S

ECTION 2 INSTALLATIONS 8

2.1 System Installation 8

2.1.1 CPU Installation 8

2.1.2 Heat Sink Installation 9

2.1.3 Memory Module Installation 10

2.1.4 Setting Jumper and DIP Switches 12

2.2 Board Layout 13

2.3 Jumper Setting 14

2.4 Connector’s Description 17

ii

CONTENTS

ECTION 3 AWARD BIOS SETUP 35

S

3.1 BIOS Instructions 35

3.2 Main Menu 36

3.3 Standard CMOS Features 38

3.4 IDE Adapters 40

3.5 Advanced BIOS Features 42

3.6 Advanced Chipset Features 46

3.7 Integrated Peripherals 49

3.8 Power Management Setup 54

3.9 PnP/PCI Configurations 58

3.10 PC Health Status 59

3.11 Frequency/Voltage Control 61

3.12 Load Fail-Safe Default 63

3.13 Load Optimized Defaults 63

3.14 Supervisor/User Password Setting 64

3.15 Exit Selecting 65

iii

iv

Introduction

SECTION 1

INTRODUCTION

1.1 Unpacking P4BGB Series

1. Take out the P4BGB series unit from the carton box, check if the unit is
properly secure in the plastic bag.

2. Check the contents of the carton box:

¡ Industrial Board ¡ Quick Reference
¡ Floppy ribbon cable ¡ ATA-66/100 HDD ribbon cable
¡ Driver CD ¡ I/O Shield
¡ Extend to front panel cable ¡ COM2 ribbon cable (1 Set)

(for K/B & M/S) (for RS-232/422/485)

1

Introduction

1.2 Description

The P4BGB Series combines the high performance and exceptional value of

®

Intel

845GV chipset with a full-featured, new generation, industrial board.
The Intel
Pentium

®

advanced 845GV chipset support regular socket 478-pins Intel®

®

4 / Celeron® processors of 1.3GHz and up to 3.06GHz, that
memory base on the FSB 400/533MHz operation supports DDR SDRAM
interface. In the meantime, the 845GV chipset integrated the VGA function
and an external graphics device on AGP (845GV support ADD card only).
The IP-4GVI83 system memory size can be up to 2GB DDR memory,
onboard Intel

®

82562ET Ethernet controller (support 10/100 Base-TX
Ethernet), Audio and with 2 COM ports, besides the IP-4GVI83 add one
6-pins connector that can extend to front of chassis for KB & MS.

The 82801DB I/O Controller Hub (ICH4) employs the Intel

®

Accelerated Hub
Architecture to make a direct connection from the graphics and memory to
the integrated Ethernet controller, the IDE controllers (ATA/33 or ATA/66 or
ATA/100), six USB ports that are supported USB 1.1/2.0 standard meets the
performance, stability and reliability requirements.

The industrial board - P4BGB is suitable and valuable for all the industry
applications, which also well support with the Windows
and Linux

®

operation system.

®

98 / 2000 / XP / NT

1.3 Features

1.3.1 Graphic & Ethernet

The P4BGB is base on the Intel

®

845GV chipset, offers users the integration

graphic, Ethernet, Audio function. The features of chipset are as below:
¡ Enhanced integrated graphics & system performance:

- Support FSB 400/533 MHz

¡ Memory:

- SDRAM PC133, DDR 266/333

- 2.0GB Max. Memory

- 2 DIMM, Non-ECC

2

Introduction

¡ IO Connectivity - ICH4:

- 6 Hi-Speed USB2.0 ports

- AC’97 Codec

- 2 Serial ports

1.3.2 Ultra ATA/66/100

The ICH4 provides two channel Ultra ATA/66/100 Bus Master IDE controller,
that support Ultra ATA/66/100 protocols, perfect for such demanding
applications as real-time video, multimedia, and high performance operating
system. A new IDE cable is required for Ultra ATA/66/100. This cable is an
80-conductor cable; however the connectors are, of course, backwards
compatible with ATA/33.

1.3.3 Hardware Monitoring

Hardware monitoring allows you to monitor various aspects of your system s
operations and status. The features include CPU temperature, voltage and
RPM of fan.

1.3.4 I/O Shield Connector

The board is equipped with an I/O back panel. Please use the appropriate
I/O shield (figure 1).

56.05

87.71

16.80

25.42

21.75

29.50

6.50

143.76

26.13

6.22

21.64

11.96

38.10

35.97

25.00

5.00

Figure 1: I/O back panel layout

3

Introduction

1.3.5 Power-On/Off (Remote)

The board has a single 20-pins connector for ATX power supplies. For ATX
power supplies that support the Remote On/Off feature, this should be
connected to the systems front panel for system Power On/Off button. The
systems power On/Off button should be a momentary button that is normally
open.

The board has been designed with “Soft Off" functions. You can turn Off the
system from one of two sources: The first is the front panel Power On/Off
the button, and the other is the "Soft Off" function (coming from the M/B

onboard circuit controller) that can be controlled by the operating system
such as Windows

®

98/SE/ME/2000 or Windows® XP.

1.3.6 IP-4GVI83 Series Overview

Function / Model IP-4GVI83

¡ Chipset Intel® 845GV
¡ LCD Function /
¡ VGA Function
¡ SCSI Function /
¡ Ethernet Function
¡ Audio Function
¡ Two EIDE Interface
¡ One Floppy Interface
¡ One Parallel Port
¡ AGP Slot 1 (for ADD card only)
¡ PCI Slots 4
¡ ISA Slots 3
¡ Serial Port 2
¡ USB 2.0 Port 6 (four ports on rear panel)
¡ Fan Connector 3
¡ External KB/MS Connector











4

Introduction

1.3.7 System Block Diagram

CRT

Device

IDE Primary

IDE Secondary

USB Port 1/2

USB Port 3/4

USB Port 5/6

FWH

AGP4X

ATA100

USB 2.0

P4 Socket 478-pins

GMCH (845GV)

760 FC-BGA

ICH4

421 BGA

Super I/O

W83627H F

DATACTRLADDR

PCI BUS

DDR266/333 X2

AC97
Audio

Codec

ISA Bridge

ClockVRM

Intel 82562

10/100

Base-TX

IT8888F

PCI SLOTS

ISA BUS

ISA SLOTS

Keyboard

Mouse

COM Port

LPT Port

Floppy

Figure 2: System Block Diagram

5

Introduction

1.4 Specifications
¡ Processor:

- Intel

®

Pentium® 4/Celeron™ processor with socket 478-pins package,

Processor operating at 1.3GHz and up to 3.06GHz

- System bus frequency at 400/533 MHz FSB

¡ Chipset:

- Intel

®

82845GV + ICH4 AGPset

¡ DRAM Module:

- Two 184-pins socket

- For DDR 266/333 SDRAM memory

- Support DDR SDRAM up to 2GB (Max.)

¡ VGA Function:

- Intel

®

845GV Chipset integrated graphic controller

- Onboard one 15-pins VGA connector

¡ LAN Function:

- Intel

®

82562ET Ethernet controller

- For 10/100Base-TX Ethernet

- Onboard one RJ-45 Ethernet connector

-

¡ Audio Function:

- AC97 audio codec

¡ External Connector:

- One 6-pins connector for extend to front panel K/B & M/S

¡ Expansion Slot:

- 1 x AGP slot (for ADD card only)

- 4 x PCI slots

- 3 x ISA slots

¡ Onboard I/O:

- On-Chip I/O integrated with K/B, M/S, FDD, Parallel and Serial,
Fast IR and Power-ON controllers

6

Introduction

¡ Onboard PCI / IDE:

- Intel

®

ICH4 south bridge controller

- PCI rev2.2 Compliant

- ACPI Compliant Power Management

- PCI Bus IDE Port with PIO /Ultra DMA-100 x 2 (up to 4 devices)

¡ Rear I/O Connectors:

- PS/2 Mouse and PS/2 style Keyboard

- D-Sub 25-pins Printer port connector

D-Sub 9-pins COM1 Serial port connector for RS-232
D-Sub 15-pins VGA connector

- 2 x USB2.0 connectors

- RJ-45 Ethernet and 2 x USB2.0 connectors

- Audio for Line-In, Line-Out, MIC phone jack

¡ Internal I/O Connectors (pin-header):

- 1 x serial port, COM2 for RS-232 / 422 / 485
(for optional serial cable with bracket)

- 2 x USB2.0 connectors (for optional USB cable with bracket)

¡ BIOS:

- Award Plug & Play BIOS

¡ Form Factor:

- 12” x 8.7” (305 x 220mm) ATX Size

¡ Weight:

- 1.44lb (650g) ---

IP-4GVI83 series

7

SECTION 2

INSTALLATIONS

2.1 System Installation

2.1.1 CPU Installation

Carefully follow the steps below in order to install the CPU:

1. Check and confirm that the jumpers are correctly set for the CPU you

are going to install (figure 3).

2. Lift the releasing lever of the Socket 478.

3. Align the pin of the CPU against the pinholes of the Socket 478. Be sure

to pay attention to the orientation of the CPU.

Figure 3: CPU Socket

4. Push down the CPU into the Socket 478.

5. Push down the release lever and lock it against the key hook.

6. Hook the hole in ZIF clip for the CPU cooling fan onto the notch on the

socket 478.

7. Place the CPU cooling fan atop the CPU surface.

8. Push down the opposite side of the ZIF clip and hook it.

9. Slide the head of the clip to left and lock it.

10. Connect the cooling fan cable to the socket as shown below. Be careful

not to place the cable on the CPU cooling fan.

8

Installations

Removing a CPU:

1. Before removing the CPU, turn off the P4BGB Series power; then wait

for about 20 minutes until the heat radiation plate of the cooling fan and
the CPU cools down.

2. To remove the CPU, lift the releasing lever of the Socket 478.
Note: The CPU and the heat radiation plate are hot. They may cause

burns.

To remove the CPU, reverse the installation steps.

2.1.2 Heat Sink & Retention Module Installation

Make sure that good contact is made between the processors and the heat
sinks & fan. Insufficient contact, incorrect types of heat sinks, fans, or
thermal compound used or improper amount of thermal compound applied
on the CPU die can cause the processors to overheat, which may crash the
system.

Heat Sink & Fan

(For P4 processor only)

Retention Module

(For P4 Heat Sink & Fan)

Installation

Figure 4: Heat Sink & Retention Module Installation

9

Installations

2.1.3 Memory Module Installation

Figure 5 display the notch marks and what they should look like on your
DIMM memory module.

DIMMs have184-pins and two notches, that will match with the onboard
DIMM socket. DIMM modules are installed by placing the chip firmly into the
socket at a 90-degree angle and pressing straight d own (figure 6) until it fits
tightly into the DIMM socket.

Figure 5: DIMM Memory and 184-pins Socket

Figure 6: Memory Installation

10

Installations

Carefully follow the steps below in order to install the DIMMs:

1. To avoid generating static electricity and damaging the DIMM, ground

yourself by touching a grounded metal surface or using a ground scrap
before you touch the DIMM.

2. Do not touch the connector of the DIMM. Dirt residue may cause a

malfunction.

3. Hold the DIMM with its notch to the front side of the P4BGB Series and

insert it completely into the socket. A DIMM should be inserted into the
inner socket first. Guiding the hole at each end of the DIMM over the
retaining post at each end of the DIMM socket.

4. If you install two DIMMs, install the second DIMM using the same

procedure as above.

5. If DIMM does not go in smoothly, do not force it. Pull it all the way out

and try again.

6. Make sure the DIMM is properly installed and locked by the tabs on both

sides of the socket.

Removing a DIMM:

To remove the DIMM, use your fingers or a small screwdriver to carefully
push away the plastic tabs that secure the DIMM at each end. Lift it out of
the socket.

Make sure you store the DIMM in an anti-static bag and must be
populated the same size and manufactory of memory modules.

11

Installations

2.1.4 Setting Jumpers and DIP Switches

There are jumpers and DIP-switches on the system board of the P4BGB
Series. You can set the jumpers to make the necessary operations.

Figure 7: Jumper Connector

For any three-pins jumpers (Figure 7), the jumper setting is 1-2 when the
jumper connects pin 1 and 2. The setting is 2-3 when pin 2 and 3 are
connected and so on. You see a number “ 1 “ and a “ 3 “ printed on the
circuit board to identify these pins. And also, there is a second way of
indication – one of the lines surrounding jumpers is thick, which indicates pin
NO.1.

To move a jumper from one position to another, use needle-nose pliers or
tweezers to pull the pin cap off the pins and move it to the desired position.

12

Installations

A

2.2 Board Layout

Jumper & Connector Location

COM1

KBMS1

LPT1

ATX1

FAN2

CPU FA N

CN2

DIMM2DIMM1

POWER FAN

FAN1

JP4

FAN3

CHASSIS FAN

TX2

FDD1

J2 J1

VGA1

USB1

USB2

BAT1

REV:1.0

JP3

IDE1 IDE2

JBAT1

LAN

AUDIO

CD IN1

AUX IN1

WOL1

USB3

ISA1

CN4

ISA2

92011

ISA3

JPB1

CN3

ADD ONLY

AGP1

PCI1

PCI2

PCI3

PCI4

13

Installations

2.3 Jumper Setting

Table for Jumper Location Description:

Use the information in the following table to change the jumpers and the DIP
switches.

Jumpers Functions

JP3 Watchdog Timer Setting Select
JP4 Power Management Setting Select

JBAT1 Clear CMOS Setting Select

JPB1 COM2 Port Setting Select

14

Installations

In order to set up the correct configuration, here is the description
about how to set the jumpers to enable/disable or change functions. All
jumpers’ location please refer to jumper location diagram.

 Watchdog Timer Setting Select: JP3

Function JP3

NMI (Default) 1-2

Reset System 2-3

y Location:

 Power Management Setting Select: JP4

Function JP4

ACPI Mode (Default) On

APM Mode Off

y Location:

15

 Clear CMOS Setting Select: JBAT1

Function JBAT1

Normal (Default) 1-2

Clear CMOS 2-3

y Location:

 COM2 Port Setting Select: JPB1

Function

RS-232 Off Off Off Off Off On
RS-422 On (Term.) On (Term.) Off On On Off
RS-485 On (Term.) On (Term.) On Off On Off

1-2 3-4 5-6 7-8 9-10 11-12

JPB1

y Location:

Installations

16

Installations

A

2.4 Connector’s Description

Connector Location

COM1

KBMS1

LPT1

ATX1

FAN2

CPU FA N

CN2

DIMM2DIMM1

POWER FAN

FAN1

JP4

FAN3

CHASSIS FAN

TX2

FDD1

J2 J1

VGA1

USB1

USB2

BAT1

REV:1.0

JP3

IDE1 IDE2

JBAT1

LAN

AUDIO

CD IN1

AUX IN1

WOL1

USB3

ISA1

CN4

ISA2

92011

ISA3

JPB1

CN3

ADD ONLY

AGP1

PCI1

PCI2

PCI3

PCI4

17

Table for Connector’s Location Description:

Use the information in the following table to change the connector.

Connectors Functions

IDE1 Primary IDE Connector

IDE2 Secondary IDE Connector
FDD1 Floppy Disk Connector
ATX2 ATX Power Connector
FAN1 Power Fan Power Connector
ATX1 ATX 12V Power Connector
FAN2 CPU Fan Power Connector

CN2 External K/B & M/S Connector

KBMS1 PS/2 Keyboard & Mouse Connector

COM1 COM1 RS-232 Serial Port Connector

LPT1 Parallel Port Connector
VGA1 CRT VGA Port Connector
USB1 USB 0/1 Connector

LAN Ethernet RJ-45 Connector

USB2 USB 2/3 Connector

AUDIO Audio Port Connector

CDIN1 CD_IN Connector

AUXIN1 AUX_IN Connector

WOL1 Wake On LAN Connector

USB3 USB 4/5 (Pin-Header) Connector

CN4 COM2 RS-232/422/485 Serial Port Connector

FAN3 Chassis Fan Power Connector

J1/J2 System Panel Indicate Connector

Installations

18

Installations

 Primary IDE Connector (40-pins 2.54mm Pitch Pin-Header with
Housing): IDE1

Pin # Assignment Pin # Assignment

1 Reset IDE 2 Ground
3 Host Data 7 4 Host Data 8
5 Host Data 6 6 Host Data 9
7 Host Data 5 8 Host Data 10

9 Host Data 4 10 Host Data 11
11 Host Data 3 12 Host Data 12
13 Host Data 2 14 Host Data 13
15 Host Data 1 16 Host Data 14
17 Host Data 0 18 Host Data 15
19 Ground 20 NC
21 DRQ 0 22 Ground
23 Host IOW 24 Ground
25 Host IOR 26 Ground
27 IOCHRDY 28 Host ALE
29 DACK 0 30 Ground
31 IRQ 14 32 No Connect
33 Address 1 34 No Connect
35 Address 0 36 Address 2
37 Chip Select 0 38 Chip Select 1
39 Activity 40 Ground

y Figure:

40 39

12

19

Installations

 Secondary IDE Connector (40-pins 2.54mm Pitch Pin-Header with
Housing): IDE2

Pin # Assignment Pin # Assignment

1 Reset IDE 2 Ground

3 Host Data 7 4 Host Data 8

5 Host Data 6 6 Host Data 9

7 Host Data 5 8 Host Data 10

9 Host Data 4 10 Host Data 11
11 Host Data 3 12 Host Data 12
13 Host Data 2 14 Host Data 13
15 Host Data 1 16 Host Data 14
17 Host Data 0 18 Host Data 15
19 Ground 20 NC
21 DRQ 1 22 Ground
23 Host IOW 24 Ground
25 Host IOR 26 Ground
27 IOCHRDY 28 Host ALE
29 DACK 1 30 Ground
31 IRQ 15 32 No Connect
33 Address 1 34 No Connect
35 Address 0 36 Address 2
37 Chip Select 0 38 Chip Select 1
39 Activity 40 Ground

y Figure:

40 39

12

20

Installations

 Floppy Disk Connector (34-pins 2.54mm Pitch Pin-Header with
Housing): FDD1

Pin # Assignment Pin # Assignment

1 Ground 2 Drive Density Selection

3 Ground 4 No Connect

5 Ground 6 Drive Density Selection

7 Ground 8 Index

9 Ground 10 Motor Enable 0
11 Ground 12 Drive Select 1
13 Ground 14 Drive Select 0
15 Ground 16 Motor Enable 1
17 Ground 18 Direction
19 Ground 20 Step
21 Ground 22 Write Data
23 Ground 24 Write Gate
25 Ground 26 Track 00
27 Ground 28 Write Protect
29 Ground 30 Read Data
31 Ground 32 Side 1 Select
33 Ground 34 Diskette Change

y Figure:

34 33

1

2

21

Installations

 ATX Power Connector: ATX2

Pin # Assignment Pin # Assignment

1 +3.3V 11 +3.3V
2 +3.3V 12 -12V
3 Ground 13 Ground
4 +5V 14 PS-ON
5 Ground 15 Ground
6 +5V 16 Ground
7 Ground 17 Ground
8 PW-OK 18 -5V
9 5VSB 19 +5V

10 +12v 20 +5V

y Figure:

10 20

1

11

 Power Fan Power Connector: FAN1

Pin # Assignment

1 Ground
2 +12V
3 Sense

y Figure:

3

1

22

Installations

1

3

 ATX 12V Power Connector: ATX1

Pin # Assignment Pin # Assignment

1 Ground 2 Ground
3 +12V 4 +12V

y Figure:

3

4

1

2

 CPU Fan Power Connector: FAN2

Pin # Assignment

1 Ground
2 +12V
3 Sense

y Figure:

23

Installations

 External K/B & M/S Connector (6-pin Male): CN2

Pin # Assignment

1 MS Clock
2 MS Data
3 KB Clock
4 KB Data
5 Ground
6 VCC

y Figure:

6

1

 PS/2 Keyboard Connector (6-pins Green Mini Din): KBMS1

Pin # Assignment Pin # Assignment

1 Keyboard data 2 NC
3 Ground 4 +5V
5 Keyboard clock 6 NC

y Figure:

6

2

5

34

1

24

Installations

 PS/2 Mouse Connector (6-pins Purple Mini Din): KBMS1

Pin # Assignment Pin # Assignment

1 Mouse data 2 NC
3 Ground 4 +5V
5 Mouse clock 6 NC

y Figure:

6

2

5

34

1

 COM1 RS-232 Serial Port Connector (D-Sub 9-pins Male): COM1

Pin # Assignment Pin # Assignment

1 DCD (Data Carrier Detect) 6 DSR (Data Set Ready)

2 RXD (Receive Data) 7 RTS (Request to Send)

3 TXD (Transmit Data) 8 CTS (Clear to Send)

4 DTR (Data T erminal Ready) 9 RI (Ring Indicator)

5 Ground

y Figure:

5

1

9

6

25

Installations

 Parallel Port Connector (D-Sub 25-pins Male): LPT1

Pin # Assignment Pin # Assignment

1 Line Printer Strobe 14 Auto Feed

2 PD 0, Parallel Data 0 15 Error

3 PD 1, Parallel Data 1 16 Initialize

4 PD 2, Parallel Data 2 17 Select

5 PD 3, Parallel Data 3 18 Ground

6 PD 4, Parallel Data 4 19 Ground

7 PD 5, Parallel Data 5 20 Ground

8 PD 6, Parallel Data 6 21 Ground

9 PD 7, Parallel Data 7 22 Ground
10 ACK, Acknowledge 23 Ground
11 Busy 24 Ground
12 Paper Empty 25 Ground
13 Select 26 N/A

y Figure:

13

1

25

14

26

Installations

 CRT VGA Port Connector (D-SUB 15-pins Female): VGA1

Pin # Assignment Pin # Assignment

1 Red 2 Green

3 Blue 4 NC

5 Ground 6 Ground

7 Ground 8 Ground

9 VCC 10 Ground
11 NC 12 DDData
13 HSync 14 VSync
15 DDClk

y Figure:

1

5

15

11

 USB 0/1 Connector (4-pins Female): USB1

Pin # Assignment Pin # Assignment

1a VCC 1b VCC
2a USB0 - 2b USB1 ­3a USB0 + 3b USB1 +
4a Ground 4b Ground

y Figure:

14

14

27

Installations

 Ethernet (82562ET) RJ-45 Connector (RJ-45 Phone–Jack): LAN

Pin # Assignment Pin # Assignment

1 Transmit output (+) 5 NC

2 Transmit output (-) 6 Receive input (-)

3 Receive input (+) 7 NC

4 NC 8 NC

y Figure:

8

1

 USB 2/3 Connector (4-pins Female): USB2

Pin # Assignment Pin # Assignment

1a VCC 1b VCC
2a USB2 - 2b USB3 ­3a USB2 + 3b USB3 +
4a Ground 4b Ground

y Figure:

14

14

28

Installations

1

 Audio Port Connector: AUDIO

Pin # Assignment

Blue Line-In

Green Line-Out

Red Mic-In

y Figure:

 CD_IN Connector: CDIN1

Pin # Assignment

1 Left CD_IN
2 Ground
3 Ground
4 Right CD_IN

y Figure:

4

29

1

3

1

 AUX_IN Connector: AUXIN1

Pin # Assignment

1 Left AUX_IN
2 Ground
3 Ground
4 Right AUX_IN

y Figure:

 Wake On LAN Connector: WOL1

Pin # Assignment

1 5VSB
2 Ground
3 Data

y Figure:

Installations

4

30

Installations

2

 USB 4/5 Connector (9-pins Pin-Header): USB3

Pin # Assignment Pin # Assignment

1 VCC 2 VCC

3 USB4 - 4 USB5 -

5 USB4 + 6 USB5 +

7 Ground 8 Ground

9 --- 10 NC

y Figure:

10

19

31

Installations

 COM2 RS-232/422/485 Serial Port Connector (14-pins Pin-Header):
CN4

Pin # Assignment Pin # Assignment

1 DCD (Data Carrier Detect) 2 RXD (Receive Data)

3 TXD (Transmit Data) 4 DTR (Data Terminal Ready)

5 Ground 6 DSR (Data Set Ready)

7 RTS (Request to Send) 8 CTS (Clear to Send)

9 RI (Ring Indicator) 10 Ground
11 TXD+ (Transmit Data+) 12 TXD- (Transmit Data-)
13 RXD+ (Receive Data+) 14 RXD- (Receive Data-)

y COM4 Figure:

2

14

1

13

Note: How to connect RS485 device with COM port ribbon cable?

Our Industrial Board encloses a COM port ribbon cable for internal
connection. RS422/485 device must connect to downside D-Sub
with 5-pin cable and signal indication as below.

For RS-232 Connector

5

1

9

For RS-422/485 Connector

6

RS-422/485:
1: TXD­2: TXD+
3: RXD­4: RXD+
5: GND

32

Installations

 Chassis Fan Power Connector: FAN3

Pin # Assignment

1 Ground
2 +12V
3 Sense

y Figure:

1

3

33

Installations

1

2

 System Panel Indicate Connector: J1 & J2

Pin # J1 Assignment Pin # J2 Assignment

PWR ON KEYLOCK

1 PWRBT- 1 Ground

2 PWRBT+ 2 KBLOCK

TB LED PWR LED

4 TBLED- 3 PWLED-

5 TBLED+ 4 NC

HDD LED

6 HDLED-

7 HDLED+ 7 +5V

IR

9 IRTX 9 NC
10 Ground 10 SPEAKER
11 IRRX
12 CIRRX 12 RESET­13 +5V 13 RESET+

5 PWLED+

SPEAKER

8 Ground

RESET

y Figure:

J

J

34

SECTION 3

AWARD BIOS SETUP

3.1 BIOS Instructions

Award’s ROM BIOS provides a built-in Setup program, which allows user to
modify the basic system configuration and hardware parameters. The
modified data will be stored in a battery-backed CMOS, so that data will be
retained even when the power is turned off. In general, the information
saved in the CMOS RAM will stay unchanged unless there is a configuration
change in the system, such as hard drive replacement or a device is added.

It is possible for the CMOS battery to fail, this will cause data loss in the
CMOS only. If this does happen you will need to reconfigure your BIOS
settings.

35

Award BIOS Setup

3.2 Main Menu

Once you enter the AwardBIOS™ CMOS Setup Utility, the Main Menu will
appear on the screen. The Main Menu allows you to select from several
setup functions and two exit choices. Use the arrow keys to select among
the items and press <Enter> to accept and enter the sub-menu.

Phoenix - AwardBIOS CMOS Setup Utility

¾ Standard CMOS Feature
¾ Advanced BIOS Feature
¾ Advanced Chipset Feature
¾ Integrated Peripherals
¾ Power Management Setup
¾ PnP/PCI Configurations
¾ PC Health Status

Esc: Quit ↑ ↓ →←: Select Item
F10: Save & Exit Setup

Time, Date, Hard Disk Type….

Note: that a brief description of each highlighted selection appears at the bottom of the screen.

¾ Frequency/Voltage Control

Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving

Setup Items:

The main menu includes the following main setup categories. Recall that
some systems may not include all entries.

Standard CMOS Features:

Use this menu for basic system configuration. See 3.3 for the details.

Advanced BIOS Features:

Use this menu to set the Advanced Features available on your system. See

3.5 for the details.

Advanced Chipset Features:

Use this menu to change the values in the chipset registers and optimize
your system's performance. See 3.6 for the details.

36

Award BIOS Setup

Integrated Peripherals:

Use this menu to specify your settings for integrated peripherals. See
section 3.7 for the details.

Power Management Setup:

Use this menu to specify your settings for power management. See 3.8 for
the details.

PnP / PCI Configuration:

This entry appears if your system supports PnP / PCI. See 3.9 for the
details.

PC Health Status:

Use this menu to show your syst em temperature, speed and voltag e status.
See 3.10 for the details.

Frequency / Voltage Control:

Use this menu to specify your settings for frequency/voltage control. See

3.11 for the details.

Load Fail-Safe Defaults:

Use this menu to load the BIOS default values for the minimal/stable
performance for your system to operate. See 3.12 for the details.

Load Optimized Defaults:

Use this menu to load the BIOS default values that are factory settings for
optimal performance system operations. While Award has designed the
custom BIOS to maximize performance, the factory has the right to change
these defaults to meet their needs. See 3.13 for the details.

Supervisor / User Password:

Use this menu to set User and Supervisor Passwords. See 3.14 for the
details.

Save & Exit Setup:

Save CMOS value changes to CMOS and exit setup. See 3.15 for the
details.

Exit Without Save:

Abandon all CMOS value changes and exit setup. See 3.15 for the details.

37

Award BIOS Setup

3.3 Standard CMOS Features

The items in Standard CMOS Setup Menu are divided into 10 categories.
Each category includes no, one or more than one setup items. Use the
arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to
select the value you want in each item.

Phoenix - AwardBIOS CMOS Setup Utility

Date: (mm:dd:yy)
Time: (hh:mm:ss)

¾ IDE Primary Master
¾ IDE Primary Slave
¾ IDE Secondary Master
¾ IDE Secondary Slave

Drive A
Drive B

Video
Halt On

Based Memory
Extended Memory
Total Memory

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

Standard CMOS Features

Wed, Aug 5 2003
16:19:20

2557 MB
None
None
None

1.44M, 3.5 in.
None

EGA/VGA
All, But Keyboard

640K
130048K
131072K

___________________________
_

Menu Level ¾
Change the day, month, year and

century

Item Help

Date: Options Month/DD/YYYY
Set the system date. Note that the ‘Day’ automatically changes when you
set the date.

Time: Options HH : MM : SS
Set the system time.

IDE Primary Master: Options are in its sub menu (described in 3.4)
Press <Enter> to enter the sub menu of detailed options.

IDE Primary Slave: Options are in its sub menu (described in 3.4)
Press <Enter> to enter the sub menu of detailed options.

38

Award BIOS Setup

IDE Secondary Master: Options are in its sub menu (described in 3.4)
Press <Enter> to enter the sub menu of detailed options.

IDE Secondary Master: Options are in its sub menu (described in 3.4)
Press <Enter> to enter the sub menu of detailed options.

Drive A/ Drive B: Options None 360K, 5.25 in/1.2M, 5.25 in/720K, 3.5 in/

1.44M, 3.5 in/2.88M, 3.5 in
Select the type of floppy disk drive installed in your system.

Video: Options EGA/VGA/CGA 40/CGA 80/MONO
Select the default video device.

Halt On: Options All Errors/No Errors/All, but Keyboard/All, but Diskette/All,
but Disk/Key
Select the situation in which you want the BIOS to stop the POST process
and notify you.

Base Memory: Option N/A
Displays the amount of conventional memory detected during boot up.

Extended Memory: Option N/A
Displays the amount of extended memory detected during boot up

Total Memory: Option N/A
Displays the total memory available in the system

39

Award BIOS Setup

3.4 IDE Adapters

The IDE adapters control the hard disk drive. Use a separate sub menu to
configure each hard disk drive.

Phoenix - AwardBIOS CMOS Setup Utility

IDE HDD Auto-Detection

IDE Primary Master
Access Mode

Capacity
Cylinder
Head
Precomp
Landing Zone
Sector

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

IDE Primary Master

Press Enter

Auto 2557 MB
Auto

13579MB
26310
16
0
26309
63

Item Help

____________________________
Menu Level ¾¾
To auto-detect the HDD’s size,

head... on this channel

IDE HDD Auto-detection: Options Press En ter
Press Enter to auto-detect the HDD on this channel. If detection is
successful, it fills the remaining fields on this menu.

IDE Primary Master: Options None, Auto and Man ua l
Selecting “Manual” lets you set the remaining fields on this screen. Selects
the type of fixed disk. "User Type" will let you select the number of cylinders,
heads, etc. Note: PRECOMP=65535 means NONE !

Access Mode: Options CHS, LBA, Large and Auto
Choose the access mode for this hard disk.

Capacity: Options Auto Display your disk drive size.
Disk drive capacity (Approximated). Note that this size is usually slightly
greater than the size of a formatted disk given by a disk-checking program.

40

Award BIOS Setup

The following options are selectable only if the ‘IDE Primary Master’ item is
set to “Manual”

Cylinder: Options Min = 0, Max = 65535
Set the number of cylinders for this hard disk.

Head: Options Min = 0, Max = 255
Set the number of read/write heads

Precomp: Options Min = 0, Max = 65535
**** Warning: Setting a value of 65535 means no hard disk

Landing zone: Options Min = 0, Max = 65535
****

Sector: Options Min = 0, Max = 255
Number of sectors per track

41

Award BIOS Setup

3.5 Advanced BIOS Features

This section allows you to configure your system for basic operation. You
have the opportunity to select the system’s default speed, boot-up
sequence, keyboard operation, shadowing and security.

Phoenix - AwardBIOS CMOS Setup Utility

Virus Warning
CPU L1 & L2 Cache
Quick Power On Self Test
APIC Mode
HDD S.M.A.R.T. Capability

¾ Boot Seq. & Floppy Setup

Boot Up NumLock Status
Gate A20 Option

Typematic Rate Setting

X Typematic Rate (Chars/Sec)
X Typematic Delay (Msec)

Security Option

OS Select For DRAM > 64MB

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

Advanced BIOS Features

Disabled
Enabled
Enabled
Disabled
Disabled
Press Enter
On
Fast
Disabled

6
250

Setup
Non-OS2

____________________________
Menu Level ¾
Allow you to choose the VIRUS

warning feature for IDE Hard Disk
boot sector protection. If this
function is enabled and someone
attempt to write data into this area,
BIOS will show a warning message
on screen and alarm beep

Item Help

Virus Warning:

Allow you to choose the VIRUS Warning feature for IDE Hard Disk boot
sector protection. If this function is enabled and someone attempt to write
data into this area, BIOS will show a warning message on screen and ala rm
beep.
Enabled---Activates automatically when the system boots up causing a
warning message to appear when anything attempts to
access the boot sector or hard disk partition table.
Disabled---No warning message will appear when anything attempts to
access the boot sector or hard disk partition table.

CPU L1 & L2 Cache:

These two categories speed up memory access. However, it depends on
CPU/chipset design.
Enabled---Enable cache
Disabled---Disable cache

42

Award BIOS Setup

Quick Power On Self Test:

This category speeds up Power On Self Test (POST) after you po wer up the
computer. If it is set to Enable, BIOS will shorten or skip some check items
during POST.
Enabled---Enable quick POST
Disabled--- Normal POST

APIC Mode:

This item allows you to enable/disable APIC Mode.
The choice: Enabled, Disabled.

HDD S.M.A.R.T Capability:

Enabled SMART hard driver functions for compatible. The default is
disabled.
The choice: Enabled, Disabled.

Boot Seq. & Floppy Setup:

Phoenix - AwardBIOS CMOS Setup Utility

First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device

Swap Floppy Drive
Boot Up Floppy Seek
Report NO FDD For Win 95

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

Boot Seq. & Floppy Setup

Floppy
HDD-0
SCSI
Enabled

Disabled
Disabled
No

____________________________
Menu Level ¾
Select your Boot Device Priority

Item Help

First/Second/Third Boot Device:

The BIOS attempts to load the operating system from the devices in the
sequence selected in these items.
The Choice: Floppy, LS/ZIP, HDD, SCSI, CDROM, LAN and Disabled.

Boot Other Device:

When enabled, the system searches all other possible locations for an
operating system if it fails to find one in the devices specified under the first,
second, and third boot devices.
The Choice: Enabled, Disabled

43

Award BIOS Setup

Swap Floppy Drive:

If the system has two floppy drives, you can swap the logical drive name
assignments.
The choice: Enabled, Disabled.

Boot Up Floppy Seek:

Seeks disk drives during boot up. Disabling speeds boot up.
The choice: Enabled, Disabled.

Report No FDD For Win 95:

Whether report no FDD for Win 95 or not.
The choice: Yes, No.

Boot Up NumLock Status:

Select power on state for NumLock.
The choice: Off, On

Gate A20 Option:

Select if chipset or keyboard controller should control GateA20.
Normal---A pin in the keyboard controller controls GateA20
Fast---Lets chipset control GateA20

Typematic Rate Setting:

Keystrokes repeat at a rate determined by the keyboard controller. When
enabled, the typematic rate and typematic delay can be selected.
The choice: Enabled, Disabled.

Typematic Rate (Chars/Sec):

Sets the number of times a second to repeat a keystroke when you hold the
key down.
The choice: 6, 8, 10, 12, 15, 20, 24 and 30.

Typematic Delay (Msec):

Sets the delay time after the key is held down before it begins to repeat the
keystroke.
The choice: 250, 500, 750 and 1000.

44

Award BIOS Setup

Security Option:

Select whether the password is required every time the system b oots or only
when you enter setup.
System---The system will not boot and access to Setup will be denied if
the correct password is not entered at the prompt.
Setup---The system will boot, but access to Setup will be denied if the
correct password is not entered at the prompt.

Note: To disable security, select PASSWORD SETTING at Main Menu and then you will be

asked to enter password. Do not type anything and just press <Enter>, it will disable
security. Once the security is disabled, the system will boot and you can enter Setup
freely.

OS Select For DRAM > 64MB:

Select the operating system that is running with greater than 64MB of RAM
on the system.
The choice: Non-OS2, OS2.

45

Award BIOS Setup

3.6 Advanced Chipset Features

This section allows you to configure the system based on the specific
features of the installed chipset. This chipset manages bus speeds and
access to system memory resources, such as DRAM and the external
cache. It also coordinates communications between the conventional ISA
bus and the PCI bus. It must be stated that these items should never need
to be altered. The default settings have been chosen because they provide
the best operating conditions for your system. The only time you might
consider making any changes would be if you discovered that data was
being lost while using your system.

Phoenix - AwardBIOS CMOS Setup Utility

DRAM Timing Selectable

X CAS Latency Time
X Active To Precharge Delay
X DRAM RAS# To CAS# Delay
X DRAM RAS# Precharge

System BIOS Cacheable

Video BIOS Cacheable

Delayed Transaction

Command Per Clock

Fast CS#

Delay Prior To Thermal

AGP Aperture Size (MB)

** On-Chip VGA Setting **

On-Chip VGA

On-Chip Frame Buffer Size

Boot Display

TV Format

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

Advanced Chipset Features

By SPD

2.5
6
3
3

Enabled
Disabled
Enabled
Auto
Auto
16Min.
64

Enabled
8MB
Auto
Auto

____________________________
Menu Level ¾

Item Help

DRAM Timing Selectable:

Select the operating system that is selecting DRAM timing, so select SPD
for setting SDRAM timing by SPD.
The choice: Manual, By SPD and Turbo.

46

Award BIOS Setup

CAS Latency Time:

When synchronous DRAM is installed, the number of clock cycles of CAS
latency depends on the DRAM timing.
The choice: 1.5, 2, and 2.5.

Active To Precharge Delay:

Select the operating system that is active to precharge delay.
The choice: 5, 6 and 7.

DRAM RAS# To CAS# Delay:

This field let’s you insert a timing delay between the CAS and RAS strobe
signals, used when DRAM is written to, read from, or refreshed. Fast gives
faster performance; and Slow gives more stable performance. This field
applies only when synchronous DRAM is installed in the system.
The choice: 2, 3.

DRAM RAS# Precharge:

If an insufficient number of cycles are allowed for the RAS to accumulate its
charge before DRAM refresh, the refresh may be incomplete and the DRAM
may fail to retain data. Fast gives faster performance; and Slow gives more
stable performance. This field applies only when synchronous DRAM is
installed in the system.
The choice: 2, 3.

System BIOS Cacheable:

Selecting “Enabled” allows caching of the system BIOS ROM at
F0000h-FFFFFh, resulting in better system performance. However, if any
program writes to this memory area, a system error may result.
The choice: Enabled, Disabled.

Video BIOS Cacheable:

Select “Enabled” allows caching of the video BIOS, resulting in better
system performance. However, if any program writes to this memory area, a
system error may result.
The choice: Enabled, Disabled.

47

Award BIOS Setup

Delayed Transaction:

The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select “Enabled” to support compliance with PCI
specification version 2.2.
The choice: Enabled, Disabled.

Command Per Clock:

Select this item allows the command per clock for system.
The choice: Auto, Enabled, Disabled.

Fast CS#:

Select this item allows the Fast CS# function.
The choice: Auto, Enabled and Disabled.

Delay Prior To Thermal:

Select this item allows the delay prior to thermal time.
The choice: 4, 8, 16 and 32 Min.

AGP Aperture Size (MB):

This field determines the effective size of the Graphic Aperture used for a
particular GMCH configuration. It can be updated by the GMCH-specific
BIOS configuration sequence before the PCI standard bus enumeration
sequence takes place. If it is not updated then a default value will select an
aperture of maximum size.
The choice: 32, 64, 128 and 256.

On-Chip VGA

Select this item allows you to control the on-chip VGA.
The choice: Enabled, Disabled.

On-Chip Frame Buffer Size:

Select this item allows you to control the on-chip frame buffer size.
The choice: 1MB, 8MB.

Boot Display:

Select this item allows you to set the boot display device.
The choice: Auto, CRT, TV and EFP.

TV Format:

Select this item allows you to set the TV format.

48

Award BIOS Setup

3.7 Integrated Peripherals

Phoenix - AwardBIOS CMOS Setup Utility

¾ Onboard IDE Device Setup
¾ Onboard PCI Device Setup
¾ Onboard I/O Chip Setup

IDE DMA transfer access

Init Display First

Intel LAN Boot ROM

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

Integrated Peripherals

Press Enter
Press Enter
Press Enter
Enabled
Onboard
Disabled

____________________________
Menu Level ¾

Item Help

Onboard IDE Device Setup:

Phoenix - AwardBIOS CMOS Setup Utility

On-Chip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-Chip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
IDE HDD Block Mode

↑↓←→Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

Onboard IDE Device Setup

Enabled
Auto
Auto
Auto
Auto
Enabled
Auto
Auto
Auto
Auto
Enabled

Item Help

____________________________
Menu Level ¾

On-Chip Primary/Secondary PCI IDE:

The integrated peripheral controller contains an IDE interface with support
for two IDE channels. Select “Enabled” to activate each channel separately.
The choice: Enabled, Disabled.

49

Award BIOS Setup

IDE Primary/Secondary Master/Slave PIO:

The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode
(0-4) for each of the four IDE devices that the onboard IDE interface
supports. Modes 0 through 4 provide successively increased performance.
In Auto mode, the system automatically determines the best mode for each
device.
The choice: Auto, Mode 0, Mode 1, Mode 2, Mode 3 and Mode 4.

IDE Primary/Secondary Master/Slave UDMA:

Ultra DMA/33 implementation is possible only if your IDE hard drive
supports it and the operating environment includes a DMA driver (Windows
95 OSR2 or a third-party IDE bus master driver). If your hard drive and your
system software both support Ultra DMA/33, select “Auto” to enable BIOS
support.
The choice: Auto, Disabled.

IDE HDD Block Mode:

Block mode is also called block transfer, multiple commands, or multiple
sector read/write. If your IDE hard drive supports block mode (most new
drives do), select Enabled for automatic detection of the optimal number of
block read/writes per sector the drive can support.
The choice: Enabled, Disabled

Onboard PCI Device Setup:

Phoenix - AwardBIOS CMOS Setup Utility

USB Controller

USB 2.0 Controller

USB Keyboard Support

USB Mouse Support

AC97 Audio

Onboard LAN Controller

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

Onboard PCI Device Setup

Enabled
Enabled
Auto
Disabled
Auto
Enabled

____________________________
Menu Level ¾

Item Help

USB/USB 2.0 Controller:

Select “Enabled” if your system contains a USB/USB2.0 controller and you
have USB peripherals.
The choice: Enabled, Disabled.

50

Award BIOS Setup

USB Keyboard Support:

Select “Enabled” if your system contains a Universal Serial Bus (USB)
controller and you have a USB keyboard.
The choice: Enabled, Disabled and Auto.

USB Mouse Support:

Select “Enabled” if your system contains a Universal Serial Bus (USB)
controller and you have a USB mouse.
The choice: Enabled, Disabled.

AC97 Audio:

This item allows you to auto or disable to support AC97 Audio.
The choice: Auto, Disabled.

Onboard LAN Controller:

Select “Enabled” to Enables the onboard LAN feature.
The choice: Enabled, Disabled.

Onboard I/O Chip Setup:

Phoenix - AwardBIOS CMOS Setup Utility

Onboard FDC Controller

Onboard Serial Port 1

Onboard Serial Port 2

UART Mode Select

X RxD, TxD Active
X IR Transmission Delay
X UR2 Duplex Mode
X Use IR Pins

Onboard Parallel Port

Parallel Port Mode

X EPP Mode Select
X ECP Mode Use DMA

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

Onboard I/O Chip Setup

Enabled
3F8/IRQ4
2F8/IRQ3
Normal

Hi, Lo
Enabled
Half
IR-Rx2Tx2

378/IRQ7
SPP

EPP1.7
3

____________________________
Menu Level ¾

If your IDE hard drive supports block
mode select Enabled for automatic
detection of the optimal number of
block read/write per sector the drive
can support

Item Help

Onboard FDC Controller:

Select “Enabled” if your system has a floppy disk controller (FDC) installed
on the system board and you wish to use it. If you install and-in FDC or the
system has no floppy drive, select Disabled in this field.
The choice: Enabled, Disabled.

51

Award BIOS Setup

Onboard Serial Port 1/Port 2:

Select an address and corresponding interrupt for the first and second serial
ports.
The choice: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled and
Auto.

UART Mode Select:

This item allows you to select UART mode.
The choice: IrDA, ASKIR and Normal.

RxD, TxD Active:

This item allows you to determine the active of RxD, TxD.
The Choice: “Hi, Hi”, “Lo, Lo”, “Lo, Hi” and “Hi, Lo”.

IR Transmission Delay:

This item allows you to enable/disable IR transmission delay.
The choice: Enabled, Disabled.

UR2 Duplex Mode:

This item allows you to select the IR half/full duplex function.
The choice: Half, Full.

Use IR Pins:

This item allows you to select IR transmission routes, one is RxD2m, TxD2
(COM Port) and the other is IR-Rx2Tx2.
The choice: IR-Rx2Tx2, RxD2 and TxD2.

Onboard Parallel Port:

This item allows you to determine access onboard parallel port controller
with which I/O address.
The choice: 3BC/IRQ7, 378/IRQ7, 278/IRQ5 and Disabled.

Parallel Port Mode:

Select an operating mode for the onboard parallel (printer) port. Select
Normal, Compatible, or SPP unless you are certain your hardware and
software both support one of the other available modes.
The choice: SPP, EPP, ECP and ECP+EPP, Normal.

52

Award BIOS Setup

EPP Mode Select:

Select EPP port type 1.7 or 1.9.
The choice: EPP1.7, 1.9.

ECP Mode Use DMA:

Select a DMA channel for the parallel port for use during ECP mode.
The choice: 3, 1.

IDE DMA transfer access:

This item allows you to enable or disable the IDE DMA transfer access.
The choice: Enabled, Disabled.

Init Display First:

This item allows you to decide to active whether PCI Slot or on-chip VGA
first.
The choice: PCI Slot, Onboard.

Intel Lan Boot ROM:

This item allows you to decide whether to invoke the boot ROM of the
onboard LAN chip.
The choice: Enabled, Disabled.

53

Award BIOS Setup

3.8 Power Management Setup

The Power Management Setup allows you to configure you system to most
effectively save energy while operating in a manner consistent with your
own style of computer use.

Phoenix - AwardBIOS CMOS Setup Utility

POWER ON Function

X KB Power ON Password

Hot Key Power ON
PWRON After PWR-Fail
Power Management
Video Off Method
Video Off In Suspend
MODEM Use IRQ
Suspend Mode
HDD Power Down
Soft-Off by PWR-BTTN
CPU THER-Throttling
Wake-Up by PCI card
Power On By Ring or WOL

Resume by Alarm

X Date (of Month) Alarm
X Time (hh:mm:ss) Alarm

** Reload Global Timer Events **

Primary IDE 0

Primary IDE 1

Secondary IDE 0

Secondary IDE 1

FDD, COM, LPT Port

PCI PIRQ [A-D]#

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

Power Management Setup

Hot KEY

Enter

Ctrl+F1
Off
User Define
DPMS
Yes
3
Disabled
Disabled
Instant-Off

50.0%
Disabled
Enabled
Disabled

0
0 : 0 : 0

Disabled
Disabled
Disabled
Disabled
Disabled
Disabled

____________________________
Menu Level ¾

Item Help

Power On Function:

You can use this item to select operating Power On the system.

The choice: Password, Hot KET, Any Key, Button and Keyboard 98.

KB Power ON Password:
You can press Enter to set the password to limit operating KB Power On
system.

54

Award BIOS Setup

Hot Key Power ON:
You can use this item to select operating Hot Key to Power On system.
The choice: Ctrl+F1 ~ Ctrl+F12

PWRON After PWR-Fail:
This item allows you to select if you want to power on the system after power
failure.
The choice: Off, Former-Sts.

Power Management:

This category allows you to select the type (or degree) of power saving and
is directly related to the following modes:

Min. Power Saving:

Minimum power management. Doze Mode = 1 hr. Standby Mode = 1
hr., Suspend Mode = 1 hr., and HDD Power Down = 15 min.

Max. Power Saving:

Maximum power management -- ONLY AVAILABLE FOR SL CPU’s.
Doze Mode = 1 min., Standby Mode = 1 min., Suspend Mode = 1 min.,
and HDD Power Down = 1 min.

User Defined:

Allow you to set each mode individually. When not disabled, each of
the ranges is from 1 min. to 1 hr. except for HDD Power Down, which
ranges from 1 min. to 15 min. and disable.

Video Off Method:

This determines the manner in which the monitor is blanked.

V/H SYNC+Blank:

This selection will cause the system to turn off the vertical and
horizontal synchronization ports and write blanks to the video buffer.

Blank Screen:

This option only writes blanks to the video buffer.

DPMS:

Initial display power management signaling.

55

Award BIOS Setup

Video Off In Suspend:

This determines the manner in which the monitor is blanked.
The choice: Yes, No.

MODEM Use IRQ:

This determines the IRQ in which the MODEM can use.
The choice: 3, 4, 5, 7, 9, 10, 11 and NA.

Suspend Mode:

When “Enabled” and after the set time of system inactivity. All devices
except the CPU will be shut off.
The choice: Disabled, 1, 2, 4, 8, 12, 20, 30, 40 Min and 1Hour.

HDD Power Down:

When “Enabled” and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
The choice: Disabled, 1 ~ 15 Min.

Soft-Off by PWR-BTTN:

Pressing the power button for more than 4 seconds forces the system to
enter the Soft-Off state when the system has “hung.”
The choice: Delay 4 Sec, Instant-Off.

CPU THER-Throttling:

Select the CPU THRM-Throttling rate.
The choice: 12.5%, 25.0%, 37.5%, 50.0%, 62.5%, 75.0% and 87.5%.

Wake-Up by PCI Card:

An input signal from PME on the PCI card awakens the system from a soft
off state.
The choice: Enabled, Disabled.

Power On by Ring or WOL:

An input signal on the serial Ring Indicator (RI) line (in other words, an
incoming call on the modem) awakens the system from a soft off state.
The choice: Enabled, Disabled.

56

Award BIOS Setup

Resume by Alarm:

When “Enabled”, your can set the date and time at which the RTC (real-time
clock) alarm awakens the system from Suspend mode.
The choice: Enabled, Disabled.

Reload Global Timer Events:

The events are I/O events whose occurrence can prevent the system from
entering a power saving mode or can awaken the system from such a mode.
In effect, the system remains alert for anything, which occurs to a device,
which is configured as Enabled, even when the system is in a power down
mode.

Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
PCI PIRQ [A-D] #

57

Award BIOS Setup

3.9 PnP/PCI Configurations
This section describes configuring the PCI bus system. PCI, or Personal
Computer Interconnect, is a system, which allows I/O devices to operate at

speeds nearing the speed the CPU itself uses when communicating with its
own special components. This section covers some very technical items
and it is strongly recommended that only experienced users should make
any changes to the default settings.

Phoenix - AwardBIOS CMOS Setup Utility

Resources Controlled By

X IRQ Resources
X DMA Resources

PCI/VGA Palette Snoop

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

PnP/PCI Configurations

Auto (ESCD)

Press Enter
Press Enter

Disabled

Item Help

_________________________
Menu Level ¾

Resource controlled by:

The Award Plug and Play BIOS has the capacity to automatically configure
all of the boot and Plug and Play compatible devices. However, this
capability means absolutely nothing unless you are using a Plug and Play
operating system such as Windows

®

95. If you set this field to “Manual”
choose specific resources by going into each of the sub menu that follows
this field (a sub menu is preceded by a “¾”).
The choice: Auto (ESCD), Manual.

IRQ/DMA Resources:

When resources are controlled manually, assign each system interrupt a
type, depending on the type of device using the interrupt.

PCI/VGA Palette Snoop:

Leave this field at “Disabled”.
The choice: Enabled, Disabled.

58

Award BIOS Setup

3.10 PC Health Status

Phoenix - AwardBIOS CMOS Setup Utility

Show PC Health in Post

Current CPU Temp.
Current System Temp.
Current Chassis Fan Speed
Current CPU Fan Speed
Current Power Fan Speed
Vagp (V)
Vcore (V)
Vdimm (V)
+ 5 V
+12 V

ACPI Shutdown Temperature

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

PC Health Status

Enabled

40°C / 104°F
24°C / 75°F
3283RPM
5152RPM
4182RPM

1.52V

1.71V

2.48V

4.81V

11.73V

Disabled

Item Help

____________________________
Menu Level ¾

Show PC Health in Post:

When this function is enabled the PC health information is displayed during
the POST(Power On SelfTest).
The choice: Enabled, Disabled.

Current CPU Temp:

Show you the current CPU temperature.

Current System Temp:

Show you the current system temperature.

Current Chassis Fan Speed:

Show you the current CPU fan operating speed.

Current CPU Fan Speed:

Show you the current CPU fan operating speed.

Current Power Fan Speed:

Show you the current Power fan operating speed.

59

Award BIOS Setup

Vagp (V)

The voltage level of Power supplied to AGP card.

Vcore (V)

The voltage level of CPU (Vcore).

Vdimm (V)

The voltage level of the DRAM.

+5V/+12V:

Show you the voltage of +5V/+12V.

APCI Shutdown Temperature:

This item allows you to set up the CPU shutdown Temperature. This item is
only effective under Windows

®

98 ACPI mode.

The choice: Disabled, 60°C / 140°F, 70°C / 158, 75°C / 167°F,

80°C / 176°F, 85°C / 185°F, 90°C / 194°F and
95°C / 203°F.

60

Award BIOS Setup

3.11 Frequency/Voltage Control

Phoenix - AwardBIOS CMOS Setup Utility

CPU Clock Ratio
Watch Dog Function
CPU FSB / SPEED
Memory Frequency

Next boot AGP/PCI is

AGP / PCI Clock

AGP/PCI subtle tuning

Clock Generation for EMI

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

Frequency/Voltage Control

19X
Disabled

100MHz/2.40GHz

Auto=>DDR266
66/33MHz
Auto

66MHz

Press Enter

____________________________
Menu Level ¾

Item Help

CPU Clock Ratio:

This item allows you to set up the CPU clock ratio, but this function depends
on different CPU performance. It is only effective for those clock ratio
haven’t been locked.

Watching Dog Function

If you select enabled and overclock fail before POST code 26h, the system
will reset automatically by default configuration.
The choice: Enabled, Disabled.

CPU FSB / SPEED:

This item allows you to enabled or disabled the CPU FSB speed.
The choice: 90MHz~ 200MHz.

Memory Frequency:

Enables you to select a ratio of the Double Data Rate Synchronous DRAM
to match the installed DRAM frequency 200/266/333MHz.

AGP/PCI Clock:

Enables you to select host clock to work concurrently with the PCI bus or the
AGP bus.

AGP/PCI subtle tuning:

Enables you to select AGP/PCI frequency.

61

Award BIOS Setup

Clock Generation for EMI:

Auto Detect PCI Clk
Spread Spectrum Modulated

↑↓→←Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-safe defaults F7: Optimized Defaults

Clock Generation for EMI

Enabled
Disabled

____________________________
Menu Level ¾

Item Help

Auto Detect PCI Clk:

When enabled the mainboard automatically disables the clock source for a
PCI slot which does not have a module in it, reducing EMI (ElectroMagnetic
Interference).
The choice: Enabled, Disabled.

Spread Spectrum Modulated:

If you enable spread spectrum, it can significantly reduce the EMI
(ElectroMagnetic Interference) generated by the system.
The choice: +/- 0.35%, +/- 0.50%, +/- 0.75%, +/- 1.0%, Disabled.

62

Award BIOS Setup

3.12 Load Fail-Safe Defaults

When you press <Enter> on this item you get a confirmation dialog box with
a message similar to:

Load Fail-Safe Defaults (Y/N)? N
Pressing ‘Y’ loads the BIOS default values for the most stable,

minimal-performance system operations.

3.13 Load Optimized Defaults

When you press <Enter> on this item you get a confirmation dialog box with
a message similar to:

Load Optimized Defaults (Y/N)? N
Pressing ‘Y’ loads the default values that are factory settings for optimal

performance system operations.

63

Award BIOS Setup

3.14 Supervisor/User Password Setting

You can set either supervisor or user password, or both of then. The
differences between are:

Set Supervisor Password: can enter and change the options of the setup
menus.

Set User Password: just can only enter but do not have the right to change
the options of the setup menus. When you select this function, the following
message will appear at the center of the screen to assist you in creating a
password.

ENTER PASSWORD:

Type the password, up to eight characters in length, and press <Enter>.
The password typed now will clear any previously entered password from
CMOS memory. You will be asked to confirm the password. Type the
password again and press <Enter>. You may also press <Esc> to abort the
selection and not enter a password.

To disable a password, just press <Enter> when you are prompted to enter
the password. A message will confirm the password will be disabled. Once
the password is disabled, the system will boot and you can enter Setup
freely.

PASSWORD DISABLED.

When a password has been enabled, you will be prompted to enter it every
time you try to enter Setup. This prevents an unauthorized person from
changing any part of your system configuration.

Additionally, when a password is enabled, you can also require the BIOS to
request a password every time your system is rebooted. This would prevent
unauthorized use of your computer.

You determine when the password is required within the BIOS Features
Setup Menu and its Security option (see Section 3). If the Security option i s
set to “System”, the password will be required both at boot and at entry to
Setup. If set to “Setup”, prompting only occurs when trying to enter Setup.

64

Award BIOS Setup

3.15 Exit Selecting

Save & Exit Setup

Pressing <Enter> on this item asks for confirmation:

Save to CMOS and EXIT (Y/N)? Y

Pressing “Y” stores the selections made in the menus in CMOS – a special
section of memory that stays on after you turn your system off. The next
time you boot your computer, the BIOS configures your system according to
the Setup selections stored in CMOS. After saving the values the system is
restarted again.

Exit Without Saving

Pressing <Enter> on this item asks for confirmation:

Quit without saving (Y/N)? Y

This allows you to exit Setup without storing in CMOS any change. The
previous selections remain in effect. This exits the Setup utility and restarts
your computer.

65