IP ONE AG3000 Series, AG503 Series, AG5000 Series User Manual

IPOne 54Mbps Wireless LAN Access Point

User’s Manual ver. 1.1.4e

IP ONE, Inc.

Gusang Bldg. 2F, 1009-5, Daechi-dong, Gangnam-gu, Seoul, 135-280, Korea http://www.ipone.co.kr Tel: +82-2-3011-0947 E-mail: sales_marketing@ipone.co.kr

☞ Models subjected to this document: AG3000/5000/503X series.

The instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual.

INFORMATION TO THE USER (Part 15.105(b))

For Class B digital device INFORMATION TO THE USER

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:

－Reorient or relocate the receiving antenna. －Increase the separation between the equipment and receiver. －Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected. －Consult the dealer or an experienced radio/TV technician for help.

WARNING (Part 15.21)

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

“Note: The manufacturer is not responsible for any Radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.”

“CAUTION: RF Exposure to Radio Frequency Radiation.

This equipment must be installed and provided minimum seperatiom distance of 20cm from the body of user and near by person. In addition to seperation distance, this device cannot be transmitted and operating in conjuction with any other transmitter or antenna.

IPOne 54Mbps AP User’s Guide

CONTENTS

ABBREVIA TION............................................................................................................................iii

CHAPTER 1. Wireless LAN Overview .......................................................................................... 1

CHAPTER 2. AP Architecture and Installation ..............................................................................2

2.1 AP Components...............................................................................................................2

2.2 AP View............................................................................................................................ 2

2.2.1 AP Front.................................................................................................................2

2.2.2 AP Rear..................................................................................................................3

2.3 AP Installation..................................................................................................................3

2.3.1 Notice before Installation....................................................................................... 3

2.3.2 Installation..............................................................................................................4

2.3.3 Notice when you use .............................................................................................4

CHAPTER 3. AP Software Configurations....................................................................................6

3.1 IPOne WOS Key Features............................................................................................... 7

3.2 AP Management System Access..................................................................................... 8

3.2.1 AP Access and TCP/IP Setting using HyperTerminal ............................................8

3.2.2 AP Access using Web Browser............................................................................12

3.2.4 AP Access using Telnet........................................................................................14

3.3 Basic Settings ................................................................................................................15

3.3.1 Configuring Operating Mode and TCP/IP............................................................15

3.3.2 Configuring Interface and Application Port..........................................................18

3.3.3 QoS Configurations .............................................................................................20

3.4 Configuring DHCP Server.............................................................................................. 23

3.5 Configuring Wireless LAN.............................................................................................. 25

3.5.1 5GHz IEEE 802.11a Radio Configuration............................................................ 25

3.5.2 2.4GHz IEEE 802.11g Radio Configuration......................................................... 28

3.6 Configuring Authentication and Accounting ...................................................................31

3.7 Configuring SNMP .........................................................................................................37

3.8 Configuring MAC Filtering and ACRM ...........................................................................39

3.8.1 MAC Filtering.......................................................................................................39

3.8.2 ACRM (Access Control for Remote Management)..............................................41

3.9 Configuring Mobile IP Foreign Agent............................................................................. 43

3.10 Configuring Management Functions............................................................................ 48

IPOne 54Mbps AP User’s Guide

3.10.1 Authenticated Users Information........................................................................ 49

3.10.2 Updating Firmware.............................................................................................51

3.10.3 System Log........................................................................................................ 54

3.10.4 System Reboot and Logout...............................................................................55

CHAPTER 4. AP Configurations According to Operation Mode................................................. 56

4.1 AP Configurations in Bridge mode................................................................................. 56

4.2 AP Configurations in Routed mode................................................................................56

4.3 AP Configurations in NAT mode.....................................................................................57

IPOne 54Mbps AP User’s Guide

iii

ABBREVIATION

AAA : Authentication, Authorization, Accounting ADSL : Asymmetric Digital Subscriber Line AP : Access Point BSS : Basic Service Set CCK : Compli mentary Code Keying CTS: Clear To Send DBPSK : Differential Binary Phase Shift Keying DC : Direct Current DHCP : Dynamic Host Configuration Protocol DNS : Domain Name Service DTIM : Delivery Traffic Indication Map DQPSK : Differential Quadrature Phase Shift Keying EAP : Extensible Authentication Protocol ESSID : Extended Service Set Identity FA: Foreign Agent GMT : Greenwich Mean Time HA: Home Agent HTTP: Hypertext Transfer Protocol IP : Internet Protocol IAPP : Inter Access Point Protocol ICMP: Internet Control Message Protocol ID: Identity IEEE : Institute of Electrical and Electronics Engineers LAN : Local Area Network LED: Light Emitting Diode MAC : Media Access Control MIP: Mobile IP MN: Mobile Node NAT : Network Address Translation NAS : Network Access Server PC : Personal Computer PCMCIA : Personal Computer Memory Card International Association POD : Pull Out Detection

IPOne 54Mbps AP User’s Guide

PoE : Power over Ethernet PPP : Point-to-Point Protocol PPPoE : Point-to-Point Protocol over Ethernet PS : Power Save RADIUS : Remote Authentication Dial In User Service RF : Radio Frequency RTS : Request To Send Rx : Receive SNMP : Simple Network Management Protocol. SNTP : Simple Network Time Protocol SSID : Service Set Identity TCP : Transmission Control Protocol TFTP : Trivial File Transfer Protocol Tx : Transmit UDP : User Datagram Protocol USB : Universal Serial Bus WAN : Wide Area Network WEP : Wired Equivalent Privacy WLAN : Wireless Local Area Network

IPOne 54Mbps AP User’s Guide

CHAPTER 1. Wireless LAN Overview

Wireless LAN (WLAN) refers to a LAN that uses high frequency radiowave instead of cables for inter-node communications. WLAN operation is specified in IEEE 802.11. Unlimited access to business applications is becoming essential. WLANs are increasingly being used to provide flexible network connectivity. WLAN solutions are typically deployed internally, usually within an office or factory environment, although they can be installed externally to provide short-range connectivity to mobile users.

WLAN benefits include:

 Increased mobility

 Fast deployment

 Network access where cabling is difficult

 Connectivity for temporary networks

Fig. 1.1.1 Wireless LAN examples

IPOne 54Mbps AP User’s Guide

CHAPTER 2. AP Architecture and Installation

2.1 AP Components

Please check the following components before installation:

① Access Point ② Antenna ③ Power Adaptor ④ RS-232 Cable (option) ⑤ CD (User’s Manual)

2.2 AP View

2.2.1 AP Front

Fig. 2.2.1 AP Front

IPOne 54Mbps AP User’s Guide

Num LED Name Color Description

① PWR Green Power status ② WL1 Green Tx/Rx data to/from WLAN port

③

WL2 Green Tx/Rx data to/from WLAN port 2

(Internal for Dual-mode AP)

④

LAN Green Tx/Rx data to/from Etherne t LAN port

(Internal for 2 port Ethernet AP)

⑤ WAN Green Tx/Rx data to/from Etherne t WAN port ⑥ SEC Green Encryption status

2.2.2 AP Rear

WAN CONSOLE LAN

RESET

POWERS/W

Fig. 2.2.2 AP Rear (Model dependent)

Num Name Description ①

WAN RJ-45 Ethernet Connect

②

CONSOLE RS-232 Serial Port

③

LAN RJ-45 Ethernet Connector (Internal for 2 port Ethernet AP)

④

RESET Factory Reset Switch

⑤

S/W Power ON/OFF Switch

⑥

POWER DC Power Connector

2.3 AP Installation

2.3.1 Notice before Installation

We recommend you to avoid these places where may be cause of performance decline or trouble:

IPOne 54Mbps AP User’s Guide

① Places with high humidity or wet condition ② Places with extreme temperature (too hot or too cold) ③ Places where change of temperature is extreme ④ Places with a lot of dusts ⑤ Places sealed with thick walls or still structure which cause high interference

2.3.2 Installation

STEP 1 Attach UTP Ethernet Cable Attach UTP Ethernet cable to AP’s RJ-45 connector and connect the other side of the cable to network equipments such as Router or Hub.

STEP 2 Attach RS-232C Serial Cable

Attach RS-232C serial cable to the AP and PC. The parameters of AP can be configured

through connection of RS-232C serial cable to the PC (Refer Chapter 3).

STEP 3 Supply Power

Plug in the DC output to AP’s power port. Make sure that the “Power” LED is on. If the “Power” LED is not on, please check the connections of the power code.

☞ Notice: Use the supplied power adapter (DC 5V, 2A) only to prevent the permanent failure of AP.

☞ Notice: Don’t use both DC power and PoE power at the same time. ☞ PoE usage: The PoE (Power over Ethernet) is the equipment that both power and data are

supplied throughput Ethernet cable. Plug in the power adapter to DC in of PoE and the Ethernet cable to Data in of PoE. Attach UTP Ethernet cable to AP’s RJ-45 connector and connect the other side of the cable to Data & Power Out of PoE (Internal for PoE supported models).

STEP 4 Confirm Installation Change settings of AP referring User’s Guide. Insert a wireless LAN card into your PC. Enter the same ESSID that you have set for the AP, using the wireless LAN card utility running on your PC. Check the signal strength of wireless link on the wireless LAN card utility.

2.3.3 Notice when you use

We recommend you to avoid the followings when you use:

① Do not disassemble on your own.

IPOne 54Mbps AP User’s Guide

② Do not drop the product or give excessive impact. ③ Do not use any parts or components, which are not provided. ④ Use only the power adapter provided. ⑤ Use the PoE only for PoE supported models.

IPOne 54Mbps AP User’s Guide

CHAPTER 3. AP Software Configurations

☞ This software configuration guide describes how to configure AG5031DU-AN2 Access

Points using web-based management system (WMS) or console-based management

system (CMS). This guide can be subject to other 54Mbps Access Points if we don’t comment specific notice.

☞ This software configuration guide is based on IPOne Access Point software, Wireless

LAN Operating System (WOS) version 1.1.14. However, this guide can be subject to other

higher WOS versions if we don’t comment specific notice.

Written by Jae-Woo So

Management Options

You can use the access point management system throughput the following interfaces:

 A web-browser interface  A command-line interface (CLI)  Simple Network Management Protocol (SNMP)

IPOne 54Mbps AP User’s Guide

3.1 IPOne WOS Key Features

The key features of IPOne WOS are as follows:

Authentication, Security, Billing

Authentication IEEE 802.1x based authentication/security

MAC address authentication

WPA Security 64/128/152 bit static WEP, 64/128 bit dynamic WEP, WPA Billing and Local Services RADIUS accounting

Session/Idle-timeout, Lost carrier detection

WEB-Redirection, white list support

Private IP allocation for guest uses

Notify user’s IP address to server

Networking and Control

IP sharing NAT Network Protocol TCP/IP, IEEE 802.1d transparent bridge, 802.1x

DHCP server/client/relay, PPPoE Access Control MAC address filtering,

Control of the maximum number of association Wireless Radio Control Radio transmission power control,

Automatic change of transmit rate,

Automatic channel selection

Roaming

L2 roaming Seamless roaming between AP’s, IEEE 802.11f IAPP support L3 roaming (Subnet roaming)

Mobile IP foreign agent support (RFC2002).

☞ This function is included only in Enterprise high-level AP

product (AG5031DU series).

Quality of Service

Downstream QoS IEEE 802.1p based downstream QoS support

Management

SNMP/MIB SNMP MIB (MIB II, WLAN MIB, 802.1x MIB, 802.1d Bridge MIB,

Enterprise MIB), Trap message Local Configurations ITU-T V.24 (EIA-RS232C), RJ-45 Port Remote Configurations Telnet, HTTP, SNMP, Web-based management Firmware Upgrade Upgrade via TFTP, FTP, HTTP

IPOne 54Mbps AP User’s Guide

3.2 AP Management System Access

3.2.1 AP Access and TCP/IP Setting using HyperTerminal

Attach RS-232C serial cable to the AP and PC. Execute “HypterTerminal” program on

your MS-Windows by following the steps.

STEP1 Execute HyperTerminal program.

STEP2 After executing the HyperTerminal, the following window will be displayed on MS-

Windows. As displayed above, type “IPOne WOS Configuration” in the name field, and

click [OK] button. You can enter any name you wish for the connection.

Fig. 3.2.1 HypterTerminal Initial Screen

STEP 3 Select the modem port as shown in the window below, and click [OK] button. In most of the cases, select either “Direct to Com1” or “Direct to Com2.”.

Fig. 3.2.2 HypterTerminal Select modem port

IPOne 54Mbps AP User’s Guide

STEP 4 You will view the following window and must set the properties of the selected COM port as shown below. Click [OK] button.

Fig. 3.2.3 HypterTerminal Port Settings

STEP 5 If all the steps above are executed correctly, then the following login prompt will be displayed on the HyperTerminal window. The default username and password is “admin” and “admin” respectively.

Fig. 3.2.4 HyperTerminal AP CMS Login

STEP 6 When username and password are correctly entered, the following [Status] menu of AP CMS (Console-based Management System) appears on the HyperTerminal window.

IPOne 54Mbps AP User’s Guide

Fig. 3.2.5 HyperTerminal AP CMS Status

In AP CMS, the command is the follows:

Command Description S <enter> AP Status C <enter> AP Configurations U <enter> AP Management Functions reboot <enter> Reboot quit <enter> Logout

IPOne 54Mbps AP User’s Guide

STEP 7 In AP CMS, configure TCP/IP information by following the steps.

① Enter the command “C” to move [Config]

menu of CMS.

② Enter the command “1” to select the menu

of [1. Basic Configuration].

③ Enter the command “y” to change

configurations.

④ Enter the proper values. Then, enter the

command “y” to apply them. If you just enter

without input of the proper value, the default

value keeps.

Fig. 3.2.6 HyperTermal TCP/IP Settings

IPOne 54Mbps AP User’s Guide

3.2.2 AP Access using Web Browser

☞ Default IP address of the AP is “10.0.0.2.” This example assumed that you change the IP address into “192.168.110.10” by using HyperTerminal.

STEP 1 Open Web Browser. We recommend beyond IE 5.0. STEP 2 Enter AP’s IP address and Port number on “Address” of the Web Browser to access AP’s WMS (Web-based Management System). The default HTTP port number is 8899.

http://[AP’s IP Address]:8899

STEP 3 Enter Username and Password. The default username and password is “admin” and “admin” respectively.

Fig. 3.2.7 AP WMS Login

STEP 4 When username and password are correctly entered, the following [Status] menu of AP WMS appears.

IPOne 54Mbps AP User’s Guide

Fig. 3.2.8 AP WMS Status

IPOne 54Mbps AP User’s Guide

3.2.4 AP Access using T elnet

☞ Default IP address of the AP is “10.10.10.2.” This example assumed that you change the IP address into “192.168.110.10” by using HyperTerminal.

STEP 1 Open “Run” on [Start] menu of MS-Windows. Enter the IP address for Internet Connection as following Example. Click [OK] button.

telenet [AP’s IP address]

Fig. 3.2.9 AP access using Telnet

STEP 2 Telnet order window appears, and please refer to “AP Access using HyperTerminal.”

Fig. 3.2.10 Telnet AP CMS Login

+ 44 hidden pages

IP ONE AG3000 Series, AG503 Series, AG5000 Series User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual