IPGARD SDHN-4D-P, SDPN-2D Quick Start Manual

DESIGNED

AND MADE

IN THE USA

NOTICE

The information contained in this document is
subject to change without notice. iPGARD makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of

merchantability and tness for particular purpose.

iPGARD will not be liable for errors contained herein
or for incidental or consequential damages in
connection with the furnishing, performance or use
of this material. No part of this document may be
photocopied, reproduced, or translated into another
language without prior written consent from
iPGARD, Inc.

20170523

SDHN-4D-P

Secure KVM Switch

Advanced 4-Port Secure

Dual-head DisplayPort to

HDMI KVM Switch with

Audio and CAC Support

Quick Start Guide

A full Manual can be downloaded from

www.ipgard.com/documentation/

TECHNICAL SPECIFICATIONS

WHAT’S IN THE BOX

VIDEO

Format DisplayPort/HDMI
Host Interface (8) DisplayPort 20-pin (female)
User Console

Interface

(2) HDMI 19-pin (female)

Max Resolution 3840x2160 @ 30Hz
DDC 5 volts p-p (TTL)
Input Equalization Automatic
Input Cable Length Up to 20 ft.
Output Cable Length Up to 20 ft.

USB

Signal Type

USB 1.1 and 1.0 Keyboard and
Mouse only.
USB 2.0 for CAC connection.

USB Type B Inputs (4) Keyboard-Mouse; (4) CAC

User Console
Output Interface

(2) USB Type-A for keyboard
and mouse connection only.
(1) USB Type-A for CAC
connection.

AUDIO

Input

(4) Connector Stereo 3.5mm
Female

Output

(1) Connector Stereo 3.5mm
Female

POWER

Power Requirements

12V DC, 2A power adapter with
center-pin positive polarity

ENVIRONMENT

Operating Temp 32° to 104° F (0° to 40° C)
Storage Temp -4° to 140° F (-20° to 60° C)
Humidity 0-80% RH, non-condensing

CERTIFICATIONS

Security Accreditation

Common Criteria Validated To

NIAP, Protection Prole PSS

Ver. 3.0

OTHER

Emulation

USB 1.1 and USB 2.0
Compatible

Control Front Panel Buttons

PART NO. QTY DESCRIPTION

SDHN-4D-P 1

4-port, Secure DH DisplayPort
to HDMI KVM Switch

PS12VDC2A 1

12V DC, 2A power adapter with
center-pin positive polarity.

1 Quick Start Guide

Toll Free: [phone]

Phone: [phone]

Fax: [phone]

3291 N. Jones Blvd.,

Las Vegas, NV 89108

iPGARD.COM

DESIGNED
AND MADE
IN THE USA

SDHN-4D-P

DP IN

AUDIO OUT

HDMI OUT

USB IN

USB OUT

CAC IN

CAC OUT

AUDIO IN

1 2 3 4

SDHN-4D-P

EDID LEARN HARDWARE INSTALLATION

A full Manual can be downloaded from

www.ipgard.com/documentation/

The KVM is designed to learn the connected
monitor’s EDID upon power up. In the event
of connecting a new monitor to the KVM, a
power recycle is required.

The KVM will indicate to the user the EDID

learn process by ashing the front panel’s

LEDs. Port one green and push button blue

LEDs will both begin to ash for about 10
seconds. When the LEDs stop ashing, the

EDID learn process is done.

If the KVM has more than one video board
(such as dual-head and quad-head models),
then the unit will continue to learn the EDIDs
of the connected monitors and indicate the

progress of the process by ashing the next

port selection green and push button blue
LEDs respectively.

The monitor must be connected to the video
output connector located in the console
space at the back of the KVM during the
EDID learn process.

If the read EDID from the connected monitor
is identical to the current stored EDID in the
KVM then the EDID learn function will be
skipped.

1. Ensure that power is turned off or disconnected from the unit and the computers.

2. Use a DisplayPort cable to connect the DisplayPort output port from each computer to the
corresponding DisplayPort IN ports of the unit.

3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the
respective USB ports of the unit.

4. Optionally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of
the computers to the AUDIO IN ports of the unit.

5. Connect the monitors to the HDMI OUT console ports of the unit using HDMI cables.

6. Connect a USB keyboard and mouse to the two USB console ports.

7. Optionally connect stereo speakers to the AUDIO OUT port of the unit.

8. Optionally connect CAC (COMMON ACCESS CARD, SMART CARD READER) to the CAC port
in the user console interface.

9. Power on the KVM by connecting a 12VDC power supply to the power connector, and then
turn on all the computers.

Note: The computer connected to port 1 will always be selected by default after power up.

Note: You can connect up to 4 computers to the 4 port KVM.

A full Manual can be downloaded from

www.ipgard.com/documentation/