IPCMAX WebTrac-4 User Manual

GPS/GSM TRACKER

USER MANUAL

IPCMAX GPS/GSM TRACKER 2

1. PREFACE

Thank you for purchasing the GPS/GSM TRACKER. This deliberately edited
manual is to introduce the tracker with the complete technical data and the
instructions showing how to operate the device smoothly and correctly. Make sure to
read this manual carefully before using this product. Most problems could be solved
through the explanations and the troubleshooting tips. Once you finish reading it, keep
it handy for necessary reference.

Please note that specification and information are subject to change without prior
notice in this manual. Any change will be integrated in the latest release. The
manufacturer assumes no responsibility for any errors or omissions in this document.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 3

2. TABLE OF CONTENTS

1. PREFACE..................................................................................................................2

2. TABLE OF CONTENTS...........................................................................................3

3. HARDWARE DESCRIPTION .................................................................................4

4. SPECIFICATIONS....................................................................................................6

5. GENERAL FUNCTION............................................................................................7

5.1.1 Park/Geofencing Protection..................................................................................7

5.1.2 Auto.......................................................................................................................8

6. EASY START .........................................................................................................10

7. SETUP .....................................................................................................................14

8. RESPOND MESSAGES .........................................................................................30

8.1.1 Uploading Auto data to URL when GPS is fixed...............................................31

8.1.2 Uploading Auto data to URL when GPS is not fixed.........................................31

8.2.1 Uploading Park data to URL when GPS is fixed................................................32

8.2.2 Activate Park when GPS is not fixed..................................................................32

8.3.1 Uploading Un-Park data to URL when GPS is fixed .........................................33

8.3.2 Uploading Un-Park data to URL ........................................................................33

8.4.1 Uploading Move report to URL when GPS is fixed...........................................34

8.4.2 Uploading Move report to URL when GPS is not fixed.....................................34

8.5.1 Uploading Poll data to URL when GPS is fixed.................................................35

8.5.2 Uploading Poll data to URL when GPS is not fixed ..........................................35

8.6.1 Uploading Low-Power data to URL when GPS is fixed....................................36

8.6.2 Uploading Low-Power data to URL when GPS is not fixed..............................37

9. APN TABLE............................................................................................................39

10. CONTACT INFORMATION................................................................................48

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 4

3. HARDWARE DESCRIPTION

3.1 Front Face

3.2 Side Face

3.3 Bottom Face

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 5

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 6

4. SPECIFICATIONS

GSM Module:

-Dual Band (EGSM 900/1800 Mhz)

-ETSI GSM Phase 2+ standard Class 4 ( 2W @ 900Mhz) Class 1 ( 1W @
1800/1900Mhz )

GPS Receiver:

-Acquisition time:

-Reacquisition < 2sec.

-Cold < 60sec. TTFF (Time To First Fix)

-Warm < 40 sec. TTFF

-Hot < 15 sec. TTFF

Accuracy:

-Position 15 meters RMS without SA

-Velocity 0,1m/s without SA

-SA Speed 0,1 km/h without SA

Picture Pixels:

-

Maximum of 120 x 160 pixels

Environmental:

-Operating Temperature : -30°C to +60°C

-Storage Temperature : -30°C to +60°C

-Relative Humidity : 5% to 95 %, non-condensing

Battery Life:

-10 hours (stand-by mode)

Size:

-66(L)x43(W)x22(H) mm

Weight:

-87g

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 7

5. GENERAL FUNCTION

GPS/GSM tracker is using the GPRS service to upload the data containing a picture
shot by camera, latitude, longitude, speed and time to an assigned mail server and
account. It is specially designed for the security and tracking applications, such as
fleet management and life security.

Note1:
When GPRS network is not available, SMS will be sent instead in the HTTP/SMS
mode.

5.1 Features

5.1.1 Park/Geofencing Protection

-There are two methods to activate GPS/GSM tracker Parking mode.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 8

Mode 1:

You can press the “Park” button on the GPS/GSM tracker when leaving a vehicle.
After the park function is activated, it will have three buzzes for noticing user of park
mode activation. Then GPS/GSM tracker will suspend the auto report function. If it is
in the GPRS coverage then it will upload a confirmation data to either the assign
IP/domain or the E-mail address. If the GPRS is not available, it will send a SMS to
the first numbers in the contacts list instead. While the GPS is not fixed, you will not
be able to activate the Park function, and it will have two buzzes to alert you.

Mode 2:

You can use any cellular phone to send a SMS message for activation and
deactivation. The behavior will be the same as by pressing the button.

-When GPS/GSM tracker has been moved from the original place and its speed is
more than certain nautical miles/hr (it’s adjustable), it will send the “Move” message
containing GPS position to either the URL, e-mail or 1st predefined number depending
on the availability of GPRS. The default interval is 60s and the total of 60 reports will
be sent. The default picture-shot interval is 5. That means one picture will sent at
every 5th report.

-Both pressing the button again and sending a “Park” command can deactivate the
Park function; and there will be one buzz sound to notice you about the deactivation.
When the parking mode is deactivated, auto report will be continued if the monitor
had set the auto report function before.

-Once GPS could not fix a position and the user tries to activate the Park function,
GPS/GSM tracker will reply a failure message to the commander.

5.1.2 Auto

-You can set up auto report function to receive a regular report, note that the default
setup is off, the monitor has to set up an interval and the message amount first, and
the auto-report function will be pending once the park function is activated.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 9

5.2 Applications

• Fleet Management

• Vehicle Security and Recovery

• Asset tracking

• Yacht watching

• Covert Tracking

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 10

6. EASY START

This chapter provides you easy methods and fundamental operations for you to use it
simply and easily. Please follow the instructions as below.

Take out the GPS/GSM tracker and the AC to DC charger. Plug in the outlet and
connect the DC plug with Power hole for 90 minutes for charging GPS/GSM tracker.

Prepare a full-subscript SIM card with pin code disabled.

Press the eject button, take out the SIM card slot and place the SIM card on the slot
and slide it back with care.

Move the GPS/GSM tracker to an opened space and view the clear sky. Switch the
power on. First, the red LED is blinking. When it becomes still, it means GPS/GSM
tracker has hooked up the GSM network. About one minute later, the blue LED lights
on and it means the GPS/GSM tracker has GPS fixed up.

6.1 Start Programming GPS/GSM tracker

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 11

Use your cell phone to send a message as below to GPS/GSM tracker to obtain the
IMEI code for logon on our website in order to read the GPS position on Internet.
This is also helping you to verify if the GPS/GSM tracker is correctly functioning.

＃Username，0000，Imei＊

If the command has been transferred successfully, GPS/GSM tracker will send an
IMEI code to your cell phone. Otherwise a failure message will be sent instead.

Then send a SMS messages (the format is seen below) to set up the APN (Access
Point Name) that is provided by your GSM provider. If you don’t know what your
APN is, please refer to the APN table or contact your local mobile phone service.

＃Username，0000，3，your APN，user，password＊

After sending the SMS command, GPS/GSM tracker will response a message to your
cell phone to see if the GPS/GSM tracker does receive the command. Please note that
the GPS/GSM tracker is not able to determine the validity of the APN.

Use your cell phone to send a SMS command seen below to predefine a cell phone
number into GPS/GSM tracker.

＃Username,0000,5,cellular phone number*

After sending the SMS command, GPS/GSM tracker will response a message to your
cell phone to see if the setup is successful. When either APN or URL is incorrect or
GPRS/URL is not available, the GPS/GSM tracker will not be able to upload the data
to the website. In any case mentioned above, the GPS/GSM tracker will send a SMS
instead containing GPS position to the 1st predefined number after 5 failed tries on
uploading the data.

Next, send a message as below to GPS/GSM tracker to program the regular auto­report, GPS/GSM tracker sends a report every minute for 99 times. If you are in the e­mail/SMS mode, it will send a picture-shot at every 3rd report.

＃Username，0000，6，60，99，3＊

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 12

After sending above SMS command, the GPS/GSM tracker will also send a
confirmation message to your cell phone to see if the setup is successful. If both APN
and Auto Report are setup successfully, you should be able to read the GPS
information from our website by proceeding the next step. If only the Auto Report
and predefining number setups are successful, you will NOT be able to read the GPS
position on our web page provided. Instead, the 1st predefined number should receive
an SMS after about 2 minutes.

Surf to following website http://www.sanav.com/eric-gga/gprs_read.aspx and
key in the IMEI code.

Surf the website, you can see that GPS/GSM tracker has uploaded the data on the web
page, which contains the IMEI code, GPRMC information, status and the latest
uploading time. You will only see the data on our website when both APN and URL
are correct.

Press the Park button, it will sound 3 “beep”, it means Park mode has been enabled.
Check the website to see if the latest status shows “PARK”. You will only see the
data on our website when both APN and URL are correct.

Press the Park button again, it sounds 1 buzz, it means Park mode has been disabled,
Check the website to see if the latest status shows “UNPA”. You will only see the
data on our website when both APN and URL are correct.

Take out the camera in the package and plug it into GPS/GSM tracker’s com port
plughole.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 13

The camera with the red mark should face the object that you want to shoot. Please
see the picture below.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 14

7. SETUP

GPS/GSM tracker currently provides 15 commands to setup. You can setup the
GPS/GSM tracker by following the instructions shown in this chapter via SMS from a
cellular phone. Key the specific SMS message in your cellular phone as the
instruction and send it to the phone number of GPS/GSM tracker. The setup messages
are showed in the following sections.

Note1: The default settings are shown as below.
a. Default GPS/GSM tracker ID is “Username”.
b. Default password is “0000”.
c. There’s no number in the default contact.
d. Default setting of Auto Report is deactivated.
e. Default setting of Park is deactivated.
f. Default limit of Move is 5kn/hr.
g. Default setting of APN is only suitable for Taiwan GSM network.
h. Default setting of IP/domain is http://www.sanav.com/eric-gga/gprs.aspx.

Note2: Before doing any setup, please ensure GPS/GSM tracker is connected with the
GSM network. The red LED must lights on. And please note that GPS/GSM tracker
must not be under Panic mode.

Note3: While you are keying in any setup message, note that NO space is allowed
between the characters in the SMS. Characters can be letters, commas or any signs.

Note4: Any setup message must be started with a “#” sign and ended up with a “*”
sign.

Note5: Only when the password, username and setup message are correct, the
GPS/GSM tracker will update information according to user’s definition. If the
command is not valid, a failure report is going to be sent to the commander cell
phone.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 15

7.1 Set up the username

You can change the ID of GPS/GSM tracker by following the format below. No space
is allowed between the characters. For example, if you send the SMS message shown
in the example below to the GPS/GSM tracker, you will change the ID from
“Username” to “ason”.

Setup format:

＃「username」，「Password」，「Function Code」，「New username」＊

Example:

＃Username，0000，1，ason＊

The following table shows each confirmation message reply after setup.

7.2 Change password

Use this SMS message example seen below to change the password of GPS/GSM
tracker. For example, by following the example below, you will change the default
password, “0000” to a new password, “1111”.

Setup format:

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 16

＃「username」，「Password」，「FunctionCode」，「new

Password」，「new Password」＊
Example:

＃Username，0000，2，1111，1111＊

The following table shows each confirmation message reply after setup.

7.3 Set up the GPRS APN (Access Point Name)

For uploading the data to a web server, you must have a set of GPRS APN from your
GSM network. Various GSM network provides different GPRS APN settings. If you
can’t find the name of your GSM service provider, please ask your GMS service
provider about the APN settings. If the username and password of APN are indefinite
or showed in blank, just leave the parameters blank (no space). You can follow the
Setup Format below to setup the APN that is provided by your GSM network.

Setup format:

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 17

＃「username」，「Password」，「FunctionCode」，「access point

name」，「user」，「password」＊

Example:
＃Username，0000，3，internet，user，password＊

The following table shows each confirmation message reply after setup.

7.4 Set up a host name (URL) to transmit data

This command (SMS) instructs the GPS/GSM tracker to access an URL or fixed IP
for data transmission. If you send the SMS according to the example seen below to
GPS/GSM tracker, the URL “http://www.sanav.com/eric-gga/gprs.aspx“ will be
assigned to receive the data sent from the GPS/GSM tracker. Please note that the
question mark “?” or any symbol is not allowed to be keyed in behind the URL. The
GPS/GSM tracker will add the necessary symbols on automatically.

Setup format:
＃「username」，「Password」，「Function Code」，「Fixed IP or URL」＊

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 18

Example:
＃Username，0000，4，http://www.sanav.com/eric-gga/gprs.aspx＊

The following table is showing each confirmation message reply after setup.

7.5 Set up the phone number list

Use this SMS message to predefine the cellular numbers (Max. of 5 numbers) by
following the format below.

Setup format:
#「username」，「Password」，「Function Code」，「PH-01」，「PH-

02」，「PH-03」*

Example:

＃Username,0000,5,[phone],[phone],[phone]*

Note that both adding and not adding the “+“ sign in front of the cellular phone

number(s) are both acceptable, while the”+” sign should precede the national code.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 19

The following table shows each confirmation message reply after setup.

Note: The program will overwrite the previous contact list if the users do this setup.

7.6 Set up the Auto Report

Use this command to set up the frequency of Auto Report. If you send the SMS
according to the example shown below to GPS/GSM tracker, you will have an Auto
Report Message every 300 seconds for 99 report and it is going to be a picture shot at
every 3

rd report. Once the loop is done, you can send a SMS message to update/renew,

or switching off it in order to restart it. Please note that, once parking mode is
activated, auto-report function will be suspended. And once the Parking mode is
deactivated, the auto-report will be back.

Note1: You may limit the amount of the Auto reply messages by inputting the digits
from 1 to 9998 in the 「times」field. When you input 9999, the Auto Report Message

will not stop unless you define a new Auto Report Setting.

Setup format:

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 20

＃「username」，「Password」，「FunctionCode」，「intervals(sec)」，「total

number of report」，「Picture shot interval」＊

Example:

＃Username，0000，6，300，99，3＊

The following table shows each confirmation message reply after setup

7.7 Remote Control to activate the parking mode from distance

Use this SMS message to activate the Park function from a distance. You can just use
a cellular phone to send the SMS according to the example shown below to the
GPS/GSM tracker to activate the Park function from a distance. When GPS/GSM
tracker is moved with the speed of more than 5 knot/hr under park mode, it will send

the “Move” message containing GPS position to either the URL or 1st predefined

number depending on the availability of GPRS. Note that it will only be activated
when the GPS is currently fixed. The interval is 60s and the total amount of data sent
will be 60.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 21

Setup format:

＃「username」，「Password」，「Function Code」＊

Example:

＃Username，0000，7＊

The following table shows each confirm message reply after setup.

7.8 All parameters reset to default

Use this SMS message to reset GPS/GSM tracker to factory default. You can just
send the SMS according to the example seen below. It will overwrite all the current
parameters to default.

Setup format: ＃「username」，「Password」，「Function Code」＊

Example: ＃Username，0000，9＊

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 22

The following table shows each confirm message reply after setup.

7.9 Acquire the report of current position

You can send the SMS according to the example shown below. It will transmit current
data to the web server (URL) at once.

Setup format:

＃「username」，「Password」，「Function Code」＊

Example:

＃Username，0000，10＊

The following table shows each confirm message reply after setup.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 23

Note that the message reply shown in previous table will only be sent back to cell
phone that sent the SMS to do configuration. The caller’s ID of cellular phone must be

activated in order to let the GPS/GSM tracker recognize the caller ID and response
accordingly.

7.10 Set up a speed limit to activate the alarm in the park mode.

When the GPS/GSM Tracker is in the Park mode, and moved by for certain speed, it
will send a “towed” alarm to the URL or predefined cell phone number according to

which transmission route is set. However, the speed limit can be adjustable by
sending it SMS command as below, the default setting is 5 Knots/hr.

Setup format:

＃「username」，「Password」，「Function Code」，「speed limit」＊

Example:

＃Username，0000，11,[2~50]＊

The following table shows each confirm message reply after setup.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 24

7.11 Set up an E-mail address to receive the data

In addition to receiving data from URL, you can also obtain data from a specified E­mail address via GPRS service. After setting up the APN, you can also define an E­mail address to receive data by following the instruction below, please note that, since
processing the transformation from APN to E-mail address might cost longer time, so
receiving data from URL is still recommended.

Setup format:
＃「username」，「Password」，「Function Code」，「Email address」＊

Example:

＃Username，0000，12，sanav/com＊

The following table shows each confirmation message reply after setup.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 25

7.12 Set up the SMTP server

After setting up the E-mail address, you still have to setup a SMTP server so that the
GPS/GSM tracker can use the SMTP server and send E-mails. Setup SMTP by
following instruction.

Setup format:
＃「username」，「Password」，「Function Code」，「SMTP server」＊

Example:
＃Username，0000，13，sanav.com＊

The following table shows each confirmation message reply after setup.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 26

7.13 Set up the router for transmitting date either by URL/IP or
E-mail

You can choose the router to transmit the data by URL/IP, E-mail or SMS message.
Please refer to the following table for setup the router.

Setup format:
＃「username」，「Password」，「Function Code」，「0, 1,2,3 or 4」＊

Example:
＃Username，0000，14，1＊

The following table describes the meaning of each segment in the message above.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 27

7.14 Inquire IMEI code

IMEI stands for international mobile equipment identification. We offer you a
command to acquire the IMEI number from GPS/GSM tracker via SMS. Actually,
every GPS/GSM tracker budget has a different default IMEI code. You can send the
SMS according to the example shown below to check its IMEI number so as to
register to the web server for tracking.

Setup format:
＃「username」，「Password」，「Function Code」＊

Example:

＃Username，0000，imei＊

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 28

The following table shows each confirmation message reply after setup.

7.15 Deactivate Panic mode

In this function, it helps you to deactivate panic mode forcedly. The SMS command is
as following.

Setup format:

＃「username」，「Password」，「Function Code」＊

Example:

＃Username，0000，offpanic＊

The following table shows each confirmation message reply after setup.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 29

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 30

8. RESPOND MESSAGES

This chapter shows you how to read and understand the different response messages
sent from GPS/GSM tracker. Please note that the picture will only be sent in the e­mail/SMS mode. When GPS/GSM tracker is in GPRS/SMS or e-mail/SMS mode it
will upload the data to the assigned URL or e-mail first. However, if GPRS service is
not available, it will send the SMS to the predefined phone number instead. In the
case of GPRS-only mode, GPS/GSM tracker will only send the data by GPRS.

Basically, there’re 6 different situations that trigger the GPS/GSM tracker to response

its position (Auto Report, Polling, Park, Un-park, Move, Low Power) and are shown
in the following pages.

Event Table:

This event table helps you to know what event triggers the response.

8.1 Auto Report

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 31

8.1.1 Uploading Auto data to URL when GPS is fixed

When executed the Auto Report according to the settings with a GPS fixed,
GPS/GSM tracker will upload the data to your URL. The data format will be like the
following.

Format:

URL?imei=IMEI,RMC=GPRMC,AUTO

Example:

http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
RMC=GPRMC,092621,A,2458.4607,N,12126.1723,E,000.0,039.1,090204,003.5,W,
A*0A,AUTO

8.1.2 Uploading Auto data to URL when GPS is not fixed

Example:

http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
RMC=GPRMC,092621,V,2458.4607,N,12126.1723,E,000.0,039.1,090204,003.5,W,
A*0A,AUTO

Note 1: When in GPRS/e-mail mode and there is no GPRS service, the report will be
sent to the 1st predefined number. In the mean while, the “IMEI” will be changed to

the “Username” and the “Username” is changeable by using SMS command.

Note 2: The “A” is the GPRMC sentence indicates the GPS status, which is GPS

fixed. If the GPS is not fixed, the letter “A” will be substituted by letter “V”.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 32

8.2 Park Response

8.2.1 Uploading Park data to URL when GPS is fixed

When Park is activated with a GPS fixed, GPS/GSM tracker will upload a data to
your URL. The data format will be like the following.

Format:

URL?imei=IMEI,RMC=GPRMC,OARK

Example:

http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
RMC=GPRMC,092621,A,2458.4607,N,12126.1723,E,000.0,039.1,090204,003.5,W,
A*0A,PARK

Note: The “A” is the GPRMC sentence indicates the GPS status, which is GPS fixed.

8.2.2 Activate Park when GPS is not fixed

When try to activate Park without a GPS fixed, GPS/GSM tracker will send a SMS to
the caller. The content will be “Park cannot be activated when there is no GPS fixed”.

Note: When in GPRS/e-mail mode and there is no GPRS service, the GPS data will
be sent to the predefined number. In the mean while, the “IMEI” will be changed to

the “Username” and the “Username” is changeable by using SMS command.

8.3 Un-Park Response

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 33

8.3.1 Uploading Un-Park data to URL when GPS is fixed

When Park is deactivated with a GPS fixed, GPS/GSM tracker will upload a data to
your URL. The data format will be like the following.

Format:

URL?imei=IMEI,RMC=GPRMC,UNPA

Example:

http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
RMC=GPRMC,092621,A,2458.4607,N,12126.1723,E,000.0,039.1,090204,003.5,W,
A*0A,UNPA

8.3.2 Uploading Un-Park data to URL

When Park is deactivated without a GPS fixed, GPS/GSM tracker will upload a data
to your URL. The data format will be like the following.

Example:

http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
RMC=GPRMC,092621,V,2458.4607,N,12126.1723,E,000.0,039.1,090204,003.5,W,
A*0A,UNPA

Note 1: When in GPRS/e-mail mode and there is no GPRS service, the GPS data will
be sent to the predefined number. In the mean while, the “IMEI” will be changed to

the “Username” and the “Username” is changeable by using SMS command.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 34

Note 2: The “A” is the GPRMC sentence indicates the GPS status, which is GPS

fixed. If the GPS is not fixed, the letter “A” will be substituted by letter “V”.

8.4 Move Response

8.4.1 Uploading Move report to URL when GPS is fixed

When the object is moved under Park mode and there is a GPS fixed, GPS/GSM
tracker will upload a data to your URL. The data format will be like the following.

Format:

URL?imei=IMEI,RMC=GPRMC,MOVE

Example:

http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
RMC=GPRMC,092621,A,2458.4607,N,12126.1723,E,000.0,039.1,090204,003.5,W,
A*0A,MOVE

8.4.2 Uploading Move report to URL when GPS is not fixed

When the object is moved under Park mode and there is no GPS fixed, GPS/GSM
tracker will upload a data to your URL. The data format will be like the following.

Example:

http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
RMC=GPRMC,092621,V,2458.4607,N,12126.1723,E,000.0,039.1,090204,003.5,W,
A*0A,MOVE

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 35

Note 1: When in GPRS/e-mail mode and there is no GPRS service, the GPS data will
be sent to the predefined number. In the mean while, the “IMEI” will be changed to

the “Username” and the “Username” is changeable by using SMS command.

Note 2: The “A” is the GPRMC sentence indicates the GPS status, which is GPS

fixed. If the GPS is not fixed, the letter “A” will be substituted by letter “V”.

Note 3: When GPS/GSM tracker is in Move mode, it will start uploading a report to
the assigned URL every minute. After 60 minutes, it will stop uploading.

Note 4: You can deactivate the Move mode by sending it a Park command SMS.

8.5 Polling Response

8.5.1 Uploading Poll data to URL when GPS is fixed

When send an SMS to poll a report with a GPS fixed, GPS/GSM tracker will upload a
data to your URL. The data format will be like the following.

Format:

URL?imei=IMEI,RMC=GPRMC,POLI

Example:

http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
RMC=GPRMC,092621,A,2458.4607,N,12126.1723,E,000.0,039.1,090204,003.5,W,
A*0A,POLI

8.5.2 Uploading Poll data to U RL when GPS is not fixed

When send an SMS to poll a report without a GPS fixed, GPS/GSM tracker will
upload the data to your URL. The data format will be like the following.

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 36

Example:

http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
RMC=GPRMC,092621,V,2458.4607,N,12126.1723,E,000.0,039.1,090204,003.5,W,
A*0A,POLI

Note 1: When in GPRS/e-mail mode and there is no GPRS service, the GPS data will
be sent to the predefined number. In the mean while, the “IMEI” will be changed to

the “Username” and the “Username” is changeable by using SMS command.

Note 2: The “A” is the GPRMC sentence indicates the GPS status, which is GPS

fixed. If the GPS is not fixed, the letter “A” will be substituted by letter “V”.

8.6 Low-Power Response

8.6.1 Uploading Low-Power data to URL when GPS is fixed

When the power is low and there is a GPS fixed, GPS/GSM tracker will upload a data
to your URL. The data format will be like the following.

Format:

URL?imei=IMEI,RMC=GPRMC,LP

Example:

http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
RMC=GPRMC,092621,A,2458.4607,N,12126.1723,E,000.0,039.1,090204,003.5,W,
A*0A,LP

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 37

8.6.2 Uploading Low-Power data to URL when GPS is not fixed

When the power is low and there is not GPS fixed, GPS/GSM tracker will upload the
data to your URL. The data format will be like the following.

Example:

http://www.sanav.com/eric-gga/gprs.aspx?imei=351277000000000&
RMC=GPRMC,092621,V,2458.4607,N,12126.1723,E,000.0,039.1,090204,003.5,W,
A*0A,LP

Note 1: When in GPRS/e-mail mode and there is no GPRS service, the GPS data will
be sent to the predefined number. In the mean while, the “IMEI” will be changed to

the “Username” and the “Username” is changeable by using SMS command.

Note 2: The “A” is the GPRMC sentence indicates the GPS status, which is GPS

fixed. If the GPS is not fixed, the letter “A” will be substituted by letter “V”.

8.7 NMEA 0183 GPRMC Sentence

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 38

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 39

9. APN TABLE

Various GSM service providers offer different GPRS APN settings. Please check the
referential tables for APN before setup. If you could not find the name(s) of your
GSM service provider(s), please ask the local GSM network about the APN settings.

Australia

Austria

Belgium

Brasil

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 40

Canada

China

Croatia

Czech Republic

Denmark

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 41

Egypt

Estonia

Finland

France

Germany

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 42

Greece

Hongkong

Hungary

India

Ireland

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 43

Israel

Italy

Lithuania

Luxembourg

Netherlands

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 44

Malaysia

Norway

Poland

Philippines

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 45

Portugal

Russia

Serbia-Montenegro

Singapore

Slovakia

Slovenia

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 46

Spain

Sweden

Switzerland

Taiwan

Thailand

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 47

Turkey

UK

USA

www.ipcmax.com / versio 1.0

IPCMAX GPS/GSM TRACKER 48

10. CONTACT INFORMATION

GPS/GSM/GPRS Tracker is distributed by Serdex Soluions Ltd.

Please visit our web shop www.ipcmax.com

Contact information:

Serdex Solutions Ltd
Tiedepuisto 4
28600 PORI
Finland

Phone [phone]
Fax [phone]
E-mail [e-mail]

www.ipcmax.com / versio 1.0