CT70 PEDESTRIAN SCRUBBER DRIER
Operating & Care Guide
LED Display
Ignition Switch/Stop
70 litre solution tank Potentiometer (Speed)
75 litre recovery tank Forward/Reverse
50 cm (20”) 55 cm (22”) Brush Start/Stop
60 cm (24”) 70 cm (28”) Vacuum Start/Stop
Scrub Widths. Battery Level Indicator
Recovery Tank Full
Solution Tank Empty
MACHINE OPERATION DAILY CARE
1. Fill Solution Tank. 1. Drain Recovery Tank
2. Ignition Switch On 2. Flush Recovery Tank with Clean
Water & Wipe Off Float Switch
3. Lower Brush Head by Foot 3. Remove Vacuum Filter & Wash
Pedal. Press Down & to Left with Clean Water.
4. Lower Squeegee 4. Remove Squeegee Assembly &
Clean Rubbers Thoroughly.
5. Remove Brushes or Pads & Clean
5. Select Forward Traction Solution Flow
from Centre.
6. Wipe Down Machine
6. Open Solution Flow Lever
7. Charge Batteries, On-Board or
External Charger – 24v x 20A Min.
CT70 - Get Out Of Trouble ‘Quick’ Guide
PROBLEM / FAULT SOLUTION
1. MACHINE IS DEAD / NO POWER:- Check emergency stop button is not
depressed & batteries are connected & fully
Charged.
2. VACUUM WILL NOT OPERATE:- Check recovery tank is not full.
Check float switch is not dirty & stuck open
3. POOR DRYING:- Check squeegee blade is not worn or torn.
Check debris is not caught in the squeegee
blade. (Poor pre-sweep).
Check debris is not in suction hose.
Check vacuum filter is not dirty & blocked.
Check recovery tank lid is tight & rubber
‘0’ ring is in place.
Check vacuum hose is connected to the
Squeegee ok.
4. FLOOR IS DIFFICULT TO CLEAN:- Worn or wrong type of brush / pad.
5. STREAKY FLOORS:- Floor has not been pre-swept.
Torn or dirty squeegee.
Debris in squeegee, or Dirt on Rubbers.
Squeegee set incorrectly, Rake Angle –
Angle of Blade. ( 30◦ to 40◦)
Using the right chemical & Solution Flow Rate.
CHANGING SQUEEGEE BLADES LOCATING/CHANGING BRUSHES
IPC Gansow Squeegee rubbers have 4 working The CT70 has manual brush / pad pick up. Place
edges. Release toggle clamp, slide & remove brushes / pad under the brush head from the
the metal strap, peel off the squeegee rubber, front, lift brush head and push the brushes
turn over and replace locking toggle clamp. under, right hand brush first. Lift brush up and
turn anti-clockwise to locate, then left hand
brush, lift up and rotate clockwise to lock in
position.
RH
Check Rubber Edges are ‘Sharp’ of the blade, First
remember you have 4 x Edges to the blade.
Squeegee Rubbers & Assembly should be
Cleaned Daily, also checking for tears etc.
CT70BT70 Pad Holder = 2 x 340mm Dia.
Single disk models have auto brush on/off.
For full operating instructions, please refer to the IPC Gansow Operator Handbook.
If you require further information or assistance, please contact:-
IPC Gansow (UK)
Unit 7, Tame Valley Business Park,
Magnus, Tamworth,
Staffordshire,
B77 5BY.
Office Tel: 0044-(0)1827-288850
Office Fax: 0044-(0)1827-288583
Mobile: 07918-952733
Email: rslater@ipcleaning.com
Web Site: www.ipcgansow.com
IPC Gansow – Manufacturers of Industrial Cleaning Equipment
CT70BT60 Pad Holder = 2 x 310 mm Dia.
Loading...