PLDC01911
CT70 ECS/CT40 BT60 ECS quick guide
This Guide is intended for quick consultation only and does not replace the Use and Maintenance Manual.
Before using the machine, read the Use and Maintenance Manual c ontained in the machine p ackaging thoroughly and ri gorously respect all the
instructions.
PREPARATION/
OPERATION
1. Fill the detergent tank.
2. Release the emergency
button to turn the machine on.
3. Lower the squeegee using
the lever.
4. Press the brush button. The
machine automatically lowers
and attaches the brushes and
starts the suction motor.
5. Hold the brush button down for
3 seconds to choose the type of
operation, "MICRO SCRUB" or
with traditional brush.
6. Press the suction motor
button to disable suction if
you want to prewash the
surface.
7. Choose the direction of
movement by moving the
direction selector, turn the
potentiometer to set the
work speed.
8. Operate the drive lever.
9. Press the "H2O" button for
at least 2 seconds to
enable detergent flow.
Press the button repeatedly
to vary the quantity
delivered.
10. Adjust head pressure on
the surface to be cleaned
by pressing the button
repeatedly to vary the
pressure. The pressure
exerted is indicated by an
LED display on the control
panel.
11. Begin working.
12. When you have finished
cleaning, proceed as
follows:
• Turn the brush motor
off.
• Stop the detergent flow
• Turn the suction motor
off.
• Press the emergency
button.
• Raise the squeegee.
• If necessary, charge the
batteries.
DAILY
MAINTENANCE
Empty th e di rt y wate r drum
through the drain hose.
Clean the dirty water
drum.
Check the suction filter is
undamaged and clean.
PLDC01911
Check the detergent tank fill filter is
undamaged and clean.
Check the detergent output filter is
undamaged and clean.
Clean the brush and wash the
microfibre in a washing machine.
Check the squeegee is clean and
the blades are not damaged.
Check the battery charge.
To charge, insert the battery
charger connector into the
connector alongside the
squeegee lifting lever.
REPLACING THE SQUEEGEE BLADES
• release the clip;
• remove the two blade retainers by pushing them towards the outside of the squeegee then extracting them;
• remove the blade;
• reuse the same blade by rev ersing the edg e in contact wit h the floor until all four edges are worn out, or re place with
a new blade, fitting it onto the screws on the body of the squeegee;
• reposition the two bl ade retainers by c entring the widest par t of the slots over the fixing screws on t he squeegee
body, then pushing the blade retainers inwards;
• fasten the clip.
AUTOMATIC BRUSH ATTACHMENT
Brush attachm ent, with the head raised, re st the brushes on the floor at th e sides of the head. Push the brushe s into the head,
making sure they a re aligned with the centrin g devices in the head. P ress the brush button. Th e machine attaches the bru shes
automatically.
Brush release, stop the brushes and the su c tio n m ot o r b y pres s ing t he bru s h and s uc tio n m otor buttons. Hold the a u t om atic release button
down for at least five seconds and the machine releases the brushes from the head automatically.
TROUBLESHOOTING
THE MACHINE DOES NOT COME ON/START UP
CHECK THE EMERGENCY BUTTON IS NOT PRESSED
CHECK THE BATTERY CHARGE
THE SUCTION MOTOR DOES NOT WORK
CHECK THE DIRTY WATER DRUM IS NOT FULL
CHECK THE DIRTY WATER DRUM LEVEL SENSOR IS NOT
BLOCKED/MALFUNCTIONING
THE MACHINE LEAVES THE FLOOR WET
CHECK THE SQUEEGEE BLADES ARE NOT WORN
CHECK THERE IS NO DEBRIS BETWEEN THE TWO SQUEEGEE BLADES
CHECK THERE IS NO DEBRIS IN THE SUCTION HOSE
CHECK THE SUCTION FILTER IS UNDAMAGED AND CLEAN
CHECK THE DETERGENT TANK LID IS CLOSED CORRECTLY
CHECK THE SUCTION HOSE IS CORRECTLY ATTACHED TO THE SQUEEGEE
THE MACHINE LEAVES THE FLOOR DIRTY
CHECK THE TYPE OF BRUSH/PAD/MICROFIBRE IN USE IS SUITABLE FOR THE TYPE
OF DIRT AND FLOOR.
THE MACHINE LEAVES STRIPES OF WET FLOOR
CHECK THE FLOOR HAS BEEN BRUSHED BEFORE USING THE MACHINE
CHECK THERE IS NO DEBRIS BETWEEN THE TWO SQUEEGEE BLADES
CHECK THE SQUEEGEE BLADES ARE NOT WORN
CHECK THE SQUEEGEE IS CORRECTLY ADJUSTED
Loading...