Page 1
PLDC01849
CT90 BT Quick Guide
This Guide is intended for quick consultation only and does not replace the Use and Maintenance Manual.
Before using the machine, read the Use and Maintenance Manual c ontained in the machine p ackaging thoroughly and ri gorously respect al l the
instructions.
PREPARATION/
OPERATION
1. Fill the detergent tank.
2. R
elease the emergency
button to turn the machine
on.
3. Lo
wer the machine head by
pressing the pedal
downwards and to the left.
4. Lo
wer the squeegee using
the lever.
5. O
pen the detergent tank
tap.
6. P
ress the brush button.
7. P
ress the suction button.
8. C
hoose the direction of
movement by moving the
direction selector, turn the
potentiometer to set the
work speed.
9. O
perate the drive lever.
10. B
egin working.
11. W
hen you have finished
cleaning, proceed as
follows:
• Turn the brush motor off.
• Turn the suction motor
off.
• Press the emergency
button.
• Raise the machine head.
• Raise the squeegee.
• Close the detergent tank
tap.
• If necessary, charge the
batteries.
DAILY MAINTENANCE
Empty the dirty water drum
through the drain hose.
C
lean the dirty water drum.
C
heck the suction filter is
undamaged and clean.
C
heck the detergent tank fill filter
is undamaged and clean.
C
heck the detergent output filter
is undamaged and clean.
Page 2
PLDC01849
Clean the brushes.
Check the squeegee is clean and
the blades are not damaged.
Check the battery charge.
To charge, insert the battery
charger connector into the
connector alongside the
squeegee lifting lever.
REPLACING THE SQUEEGEE BLADES
• release the clip;
• remove the two blade retainers by pushing them towards the outside of the squeegee then extracting them;
• remove the blade;
• reus e th e same blade by reversi ng t he edge in contact wit h th e fl o or u ntil all four edges are worn o ut, or replace with a
new blade, fitting it onto the screws on the body of the squeegee;
• rep osition the two blade re tain ers b y centring the widest pa rt of the slots over the fi xi ng screws on the squeegee body,
then pushing the blade retainers inwards;
• fasten the clip.
•
AUTOMATIC BRUSH ATTACHMENT
Attaching the brushes, THIS MUST BE DONE WITH THE MACHINE O FF: position the brus hes under t he head drive disk. Lift the ri ght brush with
your hands and turn it clockwis e, l ocking it in position on th e drive disk. Lift t he left br ush with yo ur ha nds a nd t ur n it a nt icl ockwise, locking it i n p os iti o n
on the drive disk.
Removing the brushes THIS MUST BE DONE WITH THE M ACHINE OFF: raise the m achine h ead by pushi ng the h ead lift pe dal down a nd to the
right. Turn the right brush anticlockwise, releasing it from the drive disk. Turn the left brush clockwise, releasing it from the drive disk.
TROUBLESHOOTING
THE MACHINE DOES NOT COME ON/START UP
CHECK THE EMERGENCY BUTTON IS NOT PRESSED
CHECK THE BATTERY CHARGE
THE SUCTION MOTOR DOES NOT WORK
CHECK THE DIRTY WATER DRUM IS NOT FULL
CHECK THE DIRTY WATER DRUM LEVEL SENSOR IS NOT
BLOCKED/MALFUNCTIONING
THE MACHINE LEAVES THE FLOOR WET
CHECK THE SQUEEGEE BLADES ARE NOT WORN
CHECK THERE IS NO DEBRIS BETWEEN THE TWO SQUEEGEE BLADES
CHECK THERE IS NO DEBRIS IN THE SUCTION HOSE
CHECK THE SUCTION FILTER IS UNDAMAGED AND CLEAN
CHECK THE DETERGENT TANK LID IS CLOSED CORRECTLY
CHECK THE SUCTION HOSE IS CORRECTLY ATTACHED TO THE SQUEEGEE
THE MACHINE LEAVES THE FLOOR DIRTY
CHECK THE TYPE OF BRUSH/PAD IN USE IS SUITABLE FOR THE TYPE OF DIRT AND
FLOOR.
THE MACHINE LEAVES STRIPES OF WET FLOOR
CHECK THE FLOOR HAS BEEN BRUSHED BEFORE USING THE MACHINE
CHECK THERE IS NO DEBRIS BETWEEN THE TWO SQUEEGEE BLADES
CHECK THE SQUEEGEE BLADES ARE NOT WORN
CHECK THE SQUEEGEE IS CORRECTLY ADJUSTED
Loading...