Page 1
OPERATIONS
MANUAL
CT40ECS
CT70ECS
CT110ECS
Page 2
ENGLISH
2
1.
INDEX
1. INDEX................................................................................................................................... 2
2. GENERAL INFORMATION.................................................................................................. 4
2.1. S
COPE OF THE MANUAL
...................................................................................................................4
2.2. I
DENTIFYING THE MACHINE
.............................................................................................................4
2.3. D
OCUMENTATION PROVIDED WITH THE MACHINE
...........................................................................5
3. TECHNICAL INFORMATION............................................................................................... 5
3.1. G
ENERAL DESCRIPTION
...................................................................................................................5
3.2. L
EGEND
.......................................................................................................................................... 5
3.3. D
ANGER ZONES
...............................................................................................................................5
3.4. A
CCESSORIES
..................................................................................................................................6
4. SAFETY INFORMATION ..................................................................................................... 6
4.1. S
AFETY REGULATIONS
....................................................................................................................6
5. HANDLING AND INSTALLATION.......................................................................................8
5.1. L
IFTING AND TRANSPORTING THE PACKAGED MACHINE
..................................................................8
5.2. C
HECKS ON DELIVERY
.....................................................................................................................8
5.3. U
NPACKING
....................................................................................................................................8
5.4. E
LECTRICAL CONNECTIONS AND EARTH (CABLE MODELS
)..............................................................9
5.5. P
OWER SUPPLY BATTERIES (BATTERY MODELS
).............................................................................. 9
5.5.1. Batteries: preparation...............................................................................................................10
5.5.2. Batteries: installation and connection.......................................................................................10
5.6. B
ATTERY CHARGER (BATTERY MODELS
).......................................................................................11
5.6.1. Choosing the battery charger.................................................................................................... 11
5.6.2. Preparing the battery charger...................................................................................................11
5.7. L
IFTING AND TRANSPORTING THE MACHINE
..................................................................................11
6. PRACTICAL GUIDE FOR THE OPERATOR.....................................................................11
6.1. C
ONTROLS - DESCRIPTION
............................................................................................................11
6.2. M
OUNTING AND ADJUSTING THE SQUEEGEE
..................................................................................13
6.3. M
OVING THE MACHINE WHEN NOT IN OPERATION
.........................................................................13
6.4. M
OUNTING AND CHANGING THE BRUSH/DRIVE DISKS
....................................................................13
6.5. D
ETERGENTS – INSTRUCTIONS
...................................................................................................... 14
6.6. P
REPARING THE MACHINE FOR WORK
............................................................................................14
6.7. W
ORKING
......................................................................................................................................15
6.8. S
OME USEFUL TIPS TO GET THE MOST FROM YOUR SCRUBBER DRIER
............................................16
6.8.1. Prewashing using brushes or pads............................................................................................16
6.8.2. Drying..........................................................................................................................................16
6.9. D
RAINING THE DIRTY WATER
........................................................................................................17
6.10. D
RAINING THE CLEAN WATER
....................................................................................................... 17
7. PERIODS OF INACTIVITY................................................................................................. 17
8. BATTERY MAINTENANCE AND CHARGING.................................................................. 18
8.1. R
ECHARGING PROCEDURE
.............................................................................................................18
9. MAINTENANCE INSTRUCTIONS ..................................................................................... 18
9.1. M
AINTENANCE - GENERAL RULES
................................................................................................. 18
9.2. R
OUTINE MAINTENANCE
...............................................................................................................18
9.2.1 Suction motor air filter and float switch: cleaning..................................................................18
9.2.2 Basket filter: cleaning .............................................................................................................19
9.2.3 Detergent filter: cleaning ........................................................................................................ 19
9.2.4 Squeegee blades: replacing.....................................................................................................19
9.2.5 Fuses: replacement (battery models) ......................................................................................19
9.3. 1. Daily operations......................................................................................................................20
9.3.2. Weekly operations ...................................................................................................................20
9.3.3. Six monthly operations..............................................................................................................20
Page 3
ENGLISH
3
10.
TROUBLESHOOTING...................................................................................................21
10.1. H
OW TO RESOLVE POSSIBLE PROBLEMS
........................................................................................21
Page 4
ENGLISH
4
2.
GENERAL INFORMATION
Read this manual carefully before carrying out any work on the machine1.
2.1. Scope of the manual
This manual has been written by the Manufacturer and is an integral part of the machine.
It defines the purpose for which the machine has been designed and constructed and
contains all the information required by operators2.
In addition to this manual containing all user information, other publications are available
providing specific information for maintenance personnel3.
Constant respect for the instructions guarantees the safety of the operator and the
machine, low running costs and high quality results and extends the working life of the
machine. Failure to respect the instructions may lead to damage to the operator,
machine, floor being washed and environment.
To find the topic that interests you more rapidly, consult the list of contents at the
beginning of the manual.
Parts of the text requiring special attention are highlighted in bold and preceded by the
symbols illustrated and described here.
! DANGER
Indicates the need for attention in order to avoid a series of consequences which
could cause death or damage to the health of the operator.
IMPORTANT
Indicates the need for attention in order to avoid a series of consequences which
could cause damage to the machine or work environment or financial loss.
i INFORMATION
Particularly important instructions.
In line with the company's policy of constant product development and updating, the
Manufacturer reserves the right to make modifications without warning.
Although your machine may differ appreciably from the illustrations in this document,
safety and the information contained in this manual are guaranteed.
2.2. Identifying the machine
The rating plate (fig. 1) provides the following information:
• model code;
• model;
• power supply;
• total nominal power;
• serial number;
• year of fabrication;
1
The definition "machine" replaces the trade name covered by this manual.
2
Persons responsible for using the machine without performing any operations requiring precise technical skills.
3
Persons with experience, technical training and a knowledge of legislation and standards, able to perform all the
necessary operations and to recognise and avoid possible risks in handling, installation, use and maintenance of this
machine.
Page 5
ENGLISH
5
• dry weight;
• maximum slope;
• barcode with serial number;
• manufacturer's identification.
2.3. Documentation provided with the machine
• User manual;
• Guarantee certificate;
• EC certificate of conformity.
3.
TECHNICAL INFORMATION
3.1. General description
This machine is a scrubber drier for sweeping, washing and drying flat, horizontal, smooth
or moderately rough, even and obstacle free floors in civil and industrial premises. It is
available in both battery and cable versions to meet all running time and weight
requirements.
The scrubber drier spreads a solution of water and detergent in the correct concentration
on the floor and then scrubs it to remove the dirt. By carefully choosing the detergent and
brushes (or abrasive disks) from the wide range of accessories available, the machine
can be adapted to a wide range of combinations of types of floor and dirt.
A suction system incorporated in the machine dries the floor after washing by means of
the low pressure generated in the dirty water drum by the suction motor. The squeegee
connected to the drum collects the dirty water.
The machine is moved forward by:
MODEL B/C mechanical drive: the scrubber drier is provided with a special mechanical
drive device which exploits the friction between the brush and the floor to generate a
forward movement (for further details, see paragraph 6.7).
MODEL BT electric drive: the scrubber drier is moved forward by means of a special
electromechanical drive device.
3.2. Legend
The main parts of the machine are as follows (fig. 2):
• the detergent tank (fig. 2, ref. 7): contains and transports the mixture of clean water and
detergent;
• the dirty water drum (fig. 2, ref. 2): collects the dirty water picked up from the floor after
washing;
• control panel (fig. 2, ref. 1);
• head assembly (fig. 2, ref. 4): the main element is the brushes (fig. 2, ref. 5) which
distribute the detergent solution on the floor and remove the dirt;
• squeegee assembly (fig. 2, ref. 6): wipes and dries the floor by collecting the water.
• head lift pedal (fig. 2, ref. 3): raises the brush head during transport.
3.3. Danger zones
A -Tank assembly: when using certain detergents, danger of irritation for eyes, skin,
mucous membranes and respiratory tract and of asphyxia. Danger represented by
the dirt collected from the environment (germs and chemical substances). Danger of
crushing between the two tanks when the dirty water drum is replaced on the detergent
tank.
B -Control panel: danger of short circuit.
C -Bottom of washing head: danger due to brush rotation.
D -Rear wheels: danger of crushing between the wheel and chassis.
Page 6
ENGLISH
6
E -Battery compartment (in the detergent tank): danger of short circuit between the
battery poles and presence of hydrogen during charging.
3.4. Accessories
• Bristle brushes: for washing delicate floors and polishing;
• Polypropylene brushes: for normal floor washing;
• Tynex brushes: for removing accumulated stubborn dirt on resistant floors;
• Drive disks: enable the following disks to be used:
∗ Yellow disks: for washing and polishing marble and similar
surfaces;
∗ Green disks: for washing resistant floors;
∗ Black disks: for thorough washing of resistant floors with
stubborn dirt.
• MICRO SCRUB: microfibre cleaning system used for normal floor washing;
• CHEM DOSE (fig. 15): system for controlling detergent independently from the
detergent tank.
4.
SAFETY INFORMATION
4.1. Safety regulations
Read the "User Manual" carefully before start-up and use or before performing
maintenance or any other work on the machine.
IMPORTANT
Rigorously respect all instructions in the Manual (in particular those relating to
danger and important information) and on the safety plates fitted to the machine.
The Manufacturer declines all liability for damage to people or things resulting from
failure to observe the instructions.
The appliance must be used exclusively by persons trained in its use and/or who have
demonstrated their ability and have been expressly instructed to use the appliance.
The machine must not be used by minors.
The machine must not be used for purposes other than those for which it was expressly
designed. Scrupulously respect all safety standards and conditions applicable to the type
of building in which the machine is to be operated (e.g.: pharmaceutical companies,
hospitals, chemicals, etc).
Do not use the machine in places with inadequate lighting or explosive atmospheres, on
public roads, in the presence of dirt hazardous to health (dust, gas, etc) and in unsuitable
environments.
The machine is designed for temperatures of between +4°C and +35°C when in use and
between +0°C and +50°C when not in use.
The machine is designed to work in a humidity of between 30% and 95%.
Never use or pick up flammable liquids or explosives (e.g. petrol, fuel oil, etc), flammable
gases, dry dusts, acids and solvents (e.g. paint solvents, acetone etc) even if diluted.
Never pick up flaming or incandescent objects.
Never use the machine on slopes or ramps of more than 2%. In the case of slight slopes,
do not use the machine transversally, always manoeuvre with care and do not reverse.
When transporting the machine on steeper ramps or slopes, take the utmost care to avoid
tipping up and/or uncontrolled acceleration. Move the machine on ramps and/or steps
only with the brush head and squeegee raised.
Never park the machine on a slope.
Page 7
ENGLISH
7
The machine must never be left unattended with the motor or engine on. Before leaving it,
turn the motor or engine off, make sure it cannot move accidentally.
Always pay attention to other people, children in particular, present in the place where you
are working.
Never use the machine to transport people or things or to tow things. Do not tow the
machine.
Never rest objects of any weight on the machine for any reason.
Never obstruct ventilation and heat dispersion slits.
Never remove, modify or circumvent safety devices.
Numerous unpleasant experiences have shown that a wide range of personal objects
may cause serious accidents. Before beginning work, remove jewellery, watches, ties,
etc.
The operator must always use personal protection devices - protective apron or overalls,
non-slip waterproof shoes, rubber gloves, protective goggles and ear protectors and mask
to protect the respiratory tract.
Keep the hands away from moving parts.
Never use detergents other than those specified. Follow the instructions on the relative
safety sheet. Detergents should be kept out of reach of children. In the event of contact
with the eyes, wash immediately with abundant water. If swallowed, consult a doctor
immediately.
Make sure the power sockets used for the models with cable or battery charger are
connected to a suitable earth system and protected by differential thermal solenoid
switches.
Make sure the electrical characteristics of the machine (voltage, frequency, absorbed
power) given on the rating plate (fig. 1) are the same as those of the mains electricity
supply. The machine with cable has a three-wire cable and a three pin earthed plug for
use in an appropriate earthed socket. The earth wire is yellow and green. Never connect
this wire to anything other than the earth contact of the socket.
It is indispensable to respect the battery manufacturer's instructions and current
legislation. The batteries should always be kept clean and dry to avoid surface leakage
current. Protect the batteries from impurities such as metal dust.
Never rest tools on the batteries as this could cause short circuit and explosion.
When using battery acid, always follow the relative safety instructions scrupulously.
When using cable models, take care not to crush or pull the power supply cable. Check
this cable periodically for damage. If damaged, the machine must not be used.
In the presence of particularly strong magnetic fields, assess the possible effect on the
control electronics.
Never wash the machine with water jets.
The fluids collected contain detergent, disinfectant, water and organic and inorganic
material. They must be disposed off in accordance with current legislation.
In the case of malfunction and/or faulty operation, turn the machine off immediately
(disconnecting it from the mains power supply or batteries) and do not tamper. Contact a
service centre authorised by the Manufacturer.
All maintenance operations must be performed in an adequately lit place and only after
disconnecting the machine from the power supply (in cable models by unplugging the
machine from the socket, in battery models by disconnecting the batteries).
All work on the electrical system and all maintenance and repair operations other than
those explicitly described in this manual must be performed by specialised personnel
expert in the sector only.
If the power cable, plug or terminals require replacing, make sure the electrical
connections and cable grip inside the control panel are tightly fastened to guarantee the
resistance of the cable if pulled. Then replace the panel carefully to guarantee the safety
of the operator.
Only original accessories and spare parts supplied by the Manufacturer may be used in
order to guarantee safe problem-free operation of the machine. Never use parts removed
from other machines or from other kits.
Page 8
ENGLISH
8
This machine has been designed and constructed to provide ten years' service from the
fabrication date shown on the rating plate (fig. 1). After this time, whether the machine
has been used or not, it should be disposed of according to current legislation in the
country in which it is used:
- the machine must be disconnected from the power supply, emptied of liquids and
cleaned;
- the product is classified as WEEE type special waste and is covered by the
requisites of the new environmental protection regulations (2002/96/EC WEEE). It
must be disposed of separately from ordinary waste in compliance with current
legislation and standards.
Special waste. Do not dispose of with ordinary waste.
Alternatively the machine must be returned to the Manufacturer for a complete overhaul.
If you decide to stop using the machine, you are recommended to remove the batteries
and dispose of them at an authorised collection centre.
You should also make sure that all parts of the appliance which could represent a hazard,
particularly to children, are made safe.
5.
HANDLING AND INSTALLATION
5.1. Lifting and transporting the packaged machine
IMPORTANT
During all lifting operations, make sure the packaged machine is firmly anchored to
avoid it tipping up or being accidentally dropped.
Always load/unload lorries in adequately lit areas.
The machine, packaged on a wooden pallet by the Manufacturer, must be loaded using
suitable equipment (see EC Directive 2006/42 and subsequent amendments and/or
additions) onto the transporting vehicle. At destination, it must be unloaded using similar
means.
The squeegees are packed in cardboard boxes without pallet.
A fork lift truck must always be used to lift the packaged body of the machine. Handle
with care to avoid knocking or overturning the machine.
5.2. Checks on delivery
When the carrier delivers the machine, make sure the packaging and machine are both
whole and undamaged. If the machine is damaged, make sure the carrier is aware of the
damage and before accepting the goods, reserve the right (in writing) to request
compensation for the damage.
5.3. Unpacking
IMPORTANT
When unpacking the machine, the operator must be provided with the necessary
personal protection devices (gloves, goggles, etc) to limit the risk of accident.
Unpack the machine as follows:
• cut and remove the plastic straps using scissors or nippers;
• remove the cardboard;
Page 9
ENGLISH
9
• remove the bags in the battery compartment (in the detergent tank) and check the
contents:
- guarantee slip;
- use and maintenance manual;
- battery bridges with terminals (battery model only);
- 1 battery charger connector (battery models only);
• depending on the model, remove the metal brackets or cut the plastic straps fixing
the machine chassis to the pallet;
• using a sloping ramp, push the machine backwards off the pallet;
• unpack the brushes (fig. 3, ref. 1) and squeegee (fig. 3, ref. 2);
• clean the outside of the machine in respect of safety regulations;
• after unpacking the machine, install the batteries (battery models) or connect the
electrical connections (cable models). See relevant sections.
The packaging may be kept as it can be reused to protect the machine if it is moved to
another site or to a repair workshop.
Otherwise it must be disposed off in compliance with current legislation.
5.4. Electrical connections and earth (cable models)
The electrical characteristics of the machine are given on the rating plate (fig. 1). Make
sure the frequency and voltage correspond to those of the mains supply where the
machine will be operated. As far as voltage is concerned, models where the rating plate
specifies a voltage of 230 V can be used with voltages of between 220 V and 240 V.
Similarly, models rated at 115 V can be used at between 110 V and 120 V. The frequency
on the plate must always correspond to the mains voltage.
IMPORTANT
Make sure the mains circuit is suitably earthed and that the sockets (and any
adaptors used) ensure the continuity of the earth conductors.
! DANGER
Failure to observe these instructions could cause possibly serious damage to
people and things and invalidates the guarantee.
5.5. Power supply batteries (battery models)
Two different types of battery may be installed on these machines:
• tubular leak-proof batteries: the electrolyte level must be checked regularly. When
necessary, top up with distilled water until the plates are covered. Do not overfill (5 mm
max. above the plates).
• gel batteries: this type of battery requires no maintenance.
The technical characteristics must correspond to those indicated in the paragraph on the
technical specification of the machine. The use of heavier batteries could seriously
jeopardise manoeuvrability and lead to the brush motor overheating. Batteries with a
lower capacity and weight will require recharging more frequently.
They must be kept charged, dry and clean and the connections must be tight.
INFORMATION
Follow the instructions below to set the type of battery installed on the machine’s
hardware or software.
Mechanical drive version (B): on the back of the control panel, move the bridge (fig. 16)
to select the type of battery installed on the machine (ACID-LEAD/GEL)
Page 10
ENGLISH
10
Electric drive version (BT): on the back of the control panel, move the bridge (fig. 17) to
select the type of battery installed on the machine (ACID-LEAD/GEL)
CT90-MICRO SCRUB version: set the machine software to the type of battery installed,
following this sequence:
1. turn the machine on by turning the key switch (fig. 6, ref. 15), wait 5 seconds and
make sure the display comes on.
2. press the brush buttons (fig. 6, ref. 3) and suction button (fig. 6, ref. 2) together for
at least 5 seconds. This accesses the battery setting menu.
3. press the suction button (fig. 6, ref. 2) to select the type of battery installed on the
machine "ACd" for acid batteries (tubular leak-proof batteries) or "GEL" (GEL
batteries).
4. memorise the displayed parameter by pressing the emergency button (fig. 6 ref.
15).
5.5.1. Batteries: preparation
! DANGER
While installing or performing maintenance on the batteries, the operator must be
provided with the necessary personal protection devices (gloves, goggles, overalls,
etc) to limit the risk of accident. Keep away from naked flames, avoid short
circuiting the battery poles, avoid sparks and do not smoke.
The batteries are normally supplied filled with acid and ready for use.
If the batteries are dry, before mounting them on the machine, proceed as follows:
• remove the caps and fill all elements with specific sulphuric acid solution until the
plates are entirely covered (this requires at least a couple of passes for each element);
• leave for 4-5 hours to allow the air bubbles to come to the surface and the plates
to absorb the electrolyte;
• make sure the level of electrolyte is still above the plates and if necessary top up
with sulphuric acid solution;
• close the caps;
• mount the batteries on the machine (following the procedure described below).
Before starting up the machine for the first time, charge the batteries. Follow the
instructions in the relevant section.
5.5.2. Batteries: installation and connection
! DANGER
Check that all switches on the control panel are in the "0" (off) position.
Make sure you connect the terminals marked with a "+" to the positive poles of the
battery. Do not check the battery charge by sparking.
Follow the instructions given below meticulously as short circuiting the batteries
could cause them to explode.
1. Make sure the two tanks are empty (if necessary, empty them. See the relevant
paragraph).
2. Release the dirty water drum (fig. 2, ref. 2) from the detergent tank (fig. 2, ref. 7)
by pulling the catch (fig. 4, ref. 1).
3. Lift the dirty water drum and tilt it backwards by about 90°. This provides access to
the battery compartment (in the detergent tank) from above.
4. Place the batteries in the compartment in the direction shown in the drawing
printed inside the compartment on the detergent tank.
Page 11
ENGLISH
11
IMPORTANT
Mount the batteries on the machine using lifting means suitable for their weight.
The positive and negative poles have different diameters.
5) Referring to the wiring layout shown in the above diagram, connect the battery cable
and bridge terminals to the battery poles.
Arrange the cables as shown in the diagram, tighten the terminals on the poles and
cover with Vaseline.
6) Lower the dirty water drum into its work position and fasten it to the detergent tank;
7) When using the machine, follow the instructions below.
5.6. Battery charger (battery models)
IMPORTANT
Never allow the batteries to become excessively flat as this could damage them
irreparably.
5.6.1. Choosing the battery charger
Make sure the battery charger is compatible with the batteries to be charged:
− tubular lead batteries: a 24V - 20 A automatic charger is recommended. Consult the
battery charger manufacturer and manual to confirm the choice.
− gel batteries: use a charger specific for this type of battery.
5.6.2. Preparing the battery charger
If you wish to use a battery charger not provided with the machine, you must fit it with the
connector supplied with the machine (see paragraph "Unpacking" of this manual).
To install the connector, proceed as follows:
• remove about 13 mm of protective sheath from the red and black wires of the battery
charger;
• insert the wires into the connector contacts and squeeze them forcefully with suitable
pliers;
• respect the polarity (red wire + black wire –) when inserting the wires into the
connector.
5.7. Lifting and transporting the machine
IMPORTANT
All phases must be performed in an adequately lit room and adopting the safety
measures most appropriate to the situation.
The operator must always use personal protection devices.
To load the machine onto a means of transport, proceed as follows:
• empty the dirty water drum and detergent tank;
• remove the squeegee and brushes (or drive disks);
• remove the batteries (in battery models);
• place the machine on the pallet and fix it with plastic straps or metal brackets;
• lift the pallet (with the machine) using a fork lift truck and load it onto the means of
transport;
• anchor the machine to the means of transport with cables connected to the pallet and
machine itself.
6.
PRACTICAL GUIDE FOR THE OPERATOR
6.1. Controls - Description
With reference to fig. 6, the machine has the following controls and indicator lights:
Page 12
ENGLISH
12
• Power on light (fig. 6, ref. 1 - cable model only): green, indicates that the power
cable of the machine is connected to the mains.
• Battery charge light (fig. 6, ref. 1 – battery model only): 3 yellow LEDs, indicates the
battery charge level. There may be:
a) 3 LEDs on: batteries 100% to 50% charged;
b) 2 LEDs on: batteries 50% to 18% charged;
c) 1 LED on: batteries almost flat.
d) 1 LED flashing: batteries completely flat; after a few seconds the brushes
stop and the brush switch light also comes on.
• Main key switch - emergency button (fig. 6, ref. 15): enables and disables power to
all machine functions. Acts as a safety device. To start up the machine, turn the key
clockwise. To stop the machine press the button.
• Brush button with light (fig. 6, ref. 3): enables (LED on) or disables (LED off) the
"Brush" function. If the machine is fitted with the optional MICRO SCRUB system,
holding the button down for at least 3 seconds selects the machine operating mode,
with microfibre (MICRO SCRUB) or with brush/abrasive disc.
• Suction button with light (fig. 6, ref. 2): switches the suction motor responsible for
drying the floor being washed on ("LED on") or off ("LED off"). The light is on when
there is power to the suction motor.
• Tap lever (fig. 6, ref. 6): provides continuous control of the flow of detergent to the
brushes. Pull up to increase the liquid outflow.
• Drive lever (fig. 6, ref. 7): the drive lever moves the machine forwards and rotates the
brushes.
• Squeegee lever (fig. 6, ref. 8): raises (when lifted) or lowers (when pushed down) the
squeegee.
• Direction adjustment knob (fig. 6, ref. 10): turn to correct any deviation of the
machine from a straight line.
• Head lowering/raising pedal (fig. 6, ref. 9): on the left side of the machine, when
pressed it lowers/raises the brush head.
• Detergent tank level indicator (fig. 6, ref. 5): the LED comes on to indicate
insufficient water in the detergent tank.
• Dirty water drum level indicator (fig. 6, ref. 4): when the dirty water drum is full the
LED comes on and after a few seconds the suction motor shuts down.
• Display: displays any alarms active. During normal operation, it displays the hour
counter (giving the actual number of hours the machine has been operating).
• Direction selection button (CT40 - CT70 electric drive) (fig. 6, ref. 13): sets
movement of the machine to forwards or reverse.
• Alarm indicator (CT90 - MICRO SCRUB) (fig. 6, ref. 16), depending on the frequency
the LEDs come on, defines the board error code (see chapter 10). When operating
without malfunction, the LED is on steadily.
• Speed control potentiometer (CT40 electric drive - CT70 electric drive - CT90)
(fig. 6, ref. 11), turning the potentiometer sets machine speed.
• Pressure control light OPTIONAL MICRO SCRUB (fig. 6, ref. 17): consists of 3
green LEDs and 1 red LED indicating the pressure of the microfibre on the work
surface. There may be:
a) 1 green LED on: minimum pressure;
b) 2 green LEDs on: medium pressure;
c) 3 green LEDs on: maximum permitted pressure;
d) 3 green LEDs + 1 red LED on: excessive microfibre pressure. The light is
accompanied by a beep.
Page 13
ENGLISH
13
6.2. Mounting and adjusting the squeegee
The squeegee (fig. 2, ref. 6) is responsible for the first phase of drying.
To mount the squeegee on the machine, proceed as follows:
1) check that the squeegee mount (fig. 7, ref. 2) is raised, otherwise lift it by means of the
squeegee lever (fig. 7, ref. 5);
2) insert the suction hose sleeve (fig. 7, ref. 4) fully into the squeegee;
3) slacken the two knobs (fig. 7, ref. 3) at the centre of the squeegee;
4) insert the two threaded pins into the slots on the support (fig. 7, ref. 2);
5) fix the squeegee by tightening the two knobs (fig. 7, ref. 3).
The squeegee blades scrape the film of water and detergent from the floor and prepare
the way for perfect drying. With time, the constant rubbing makes the edge of the blade
in contact with the floor rounded and cracked, reducing the drying efficiency and requiring
it to be replaced. The state of wear should be checked frequently.
For perfect drying, the squeegee must be adjusted in such a way that the edge of the rear
blade bends during operation by about 45° with resp ect to the floor at every point. Adjust
the angle of the blade during operation by regulating the height of the two wheels
positioned behind the squeegee (fig. 7 ref. 1).
6.3. Moving the machine when not in operation
To move the machine, proceed as follows:
1) raise the squeegee;
2) push the head pedal down then to the right (fig. 6 ref. 9) to raise the head;
3) move the machine as follows:
- Versions with mechanical drive: push or pull;
- Versions with electric drive (CT40 – CT70 only): to move the machine forwards,
press the button (fig. 6 ref. 13), (LED fig. 6 ref. 14 on) and then operate the drive
lever (fig. 6 ref. 7). To move the machine backwards, press the button (fig. 6 ref. 13)
again, (LED fig. 6 ref. 12 on), then operate the drive lever (fig. 6. ref. 7);
speed can be varied by the potentiometer knob (fig. 6. ref. 11).
Versions with electric drive (CT90 only): to move the machine forwards/backwards,
move the selector (fig. 6, ref. 13), then use the drive lever (fig. 6. ref. 7). Speed can be
varied by the potentiometer knob (fig. 6. ref. 11).
4) once you have reached your destination, lower the head by pressing the release
pedal (fig. 6 ref. 9) down and to the left, then release it.
IMPORTANT
Do not leave the machine unattended or parked with the head lifted or the key
inserted in the emergency button.
6.4. Mounting and changing the brush/drive disks
IMPORTANT
Never work without the brushes and drive disks perfectly installed.
Fitting the brush (one brush version): Rest the brush on the floor in front of the
machine and centre it with the guard. Lower the head and repeatedly action the
brush/drive control lever (fig. 6, ref. 7) until the brush automatically engages on the flange
hub. If the manoeuvre is not successful, press on the handle again and repeat the
centring and repeated actioning of the brush/drive lever.
Use of abrasive/microfibre disks: fit the abrasive/microfibre disk on the drive disk and
perform the operations described for fitting the brush on the scrubber drier.
Removing the brush (one brush version) (or drive disk):
Raise the machine head by pushing the head lift pedal down and then to the right (fig. 6,
ref. 9) and repeatedly action the brush/drive lever. After a few pulses, the brush/es (or
drive disk) is released and falls to the ground.
Page 14
ENGLISH
14
Fitting the brushes (two brush version):
Place the brushes under the head drive disk.
Lift the right brush with your hands and turn it clockwise, locking it in position on the drive
disk. Lift the left brush with your hands and turn it anticlockwise, locking it in position on
the drive disk.
Use of abrasive/microfibre disks: fit the abrasive/microfibre disk on the drive disk and
perform the operations described for fitting the brush on the scrubber drier.
Removing the brushes (two brush version) (or drive disk):
Raise the machine head by pushing the head lift pedal down and then to the right (fig. 6,
ref. 9). Turn the right brush anticlockwise, releasing it from the drive disk. Turn the left
brush clockwise, releasing it from the drive disk.
6.5. Detergents – Instructions
IMPORTANT
Always dilute the detergent according to the manufacturer's instructions. Do not
use sodium hypochlorite (bleach) or other oxidants, particularly in strong
concentrations. Do not use solvents or hydrocarbons. The temperature of the
water and detergent must not exceed the maximum indicated in the technical
specification. They must be free of sand and/or other impurities.
The machine has been designed for use with low-foam biodegradable detergents made
specifically for scrubber driers.
For a complete and up-to-date list of the detergents and chemicals available, contact the
Manufacturer.
Use products suitable for the floor and dirt to be removed only.
Follow the safety regulations on use of detergents given in the section "Safety
regulations".
6.6. Preparing the machine for work
IMPORTANT
Before starting work, wear overalls, ear protectors, non-slip waterproof shoes,
mask to protect the respiratory tract, gloves and all other personal protection
devices recommended by the supplier of the detergent used or necessitated by the
work environment.
Before starting work, proceed as follows:
• Battery models: check the battery charge (recharge if necessary);
• lower the head by means of the pedal (fig. 6, ref. 9);
• make sure the dirty water drum (fig. 2, ref. 2) is empty. If necessary, empty it;
• check that the tap lever (fig. 6, ref. 6) is in the "CLOSED" position;
• via the opening at the front, fill the detergent tank (fig. 2, ref. 7) with a suitable
concentration of clean water and low-foam detergent. Leave at least 5 cm between the
surface of the liquid and the opening of the tank;
• if the machine is fitted with the optional CHEM DOSE accessory, remove the cap and
fill the tank (fig. 15, ref. 1) with appropriately diluted low-foam detergent.
• mount the most suitable brushes or drive disks for the floor and work to be performed
(see paragraph 3.4);
• make sure the squeegee (fig. 2, ref. 6) is firmly attached and connected to the suction
hose (fig. 7, ref. 4). Make sure the back blade is not worn.
i INFORMATION
If you are using the machine for the first time, we recommend trying it on a large
obstacle-free surface first to acquire the necessary familiarity.
Always empty the dirty water drum before filling the detergent tank again.
For effective cleaning and to extend the working life of the machine, follow a few simple
rules:
Page 15
ENGLISH
15
• prepare the work area by removing all possible obstacles;
• begin working from the furthermost point to avoid walking on the area you have just
cleaned;
• choose the straightest possible working routes;
• divide large floors into parallel rectangular sections.
If necessary, finish off by passing a mop or rag rapidly over parts inaccessible to the
scrubber drier.
6.7. Working
After setting up the machine, proceed as follows:
• Connect the machine as follows:
- cable model: plug the machine into the mains power socket;
• move the tap lever (fig. 6, ref. 6) to the minimum detergent flow position. Unless a
safety solenoid valve is fitted, the detergent solution starts flowing to the brush;
• lower the squeegee by means of the corresponding lever (fig. 6, ref. 8);
• press the brush switch (fig. 6, ref. 3). If the machine is set to also operate using the
MICRO SCRUB system, select the most suitable operating mode (brush/pad mode or
MICRO SCRUB mode) by holding the brush switch down for at least 3 seconds;
• press the suction switch (fig. 6, ref. 2) to start the suction motor;
• press the brush/drive lever (fig. 6, ref. 7);
• Versions with mechanical drive: When the brush switch is in the "1" position and
the drive lever is pulled, the motor which turns the brush and moves the machine starts
up. A special mechanical drive device uses the friction between the brush and floor to
generate a forward movement. When the mechanical drive lever is released, the brush
motor shuts down and the machine stops.
If the machine pulls to one side, restore a straight course by using the direction regulation
knob (fig. 6, ref. 10). If the machine pulls to the right, turn the knob clockwise and vice
versa.
• Versions with electric drive: to move forwards or backwards, see paragraph 6.3.
In both versions:
• periodically check that the detergent is reaching the brushes and refill when it runs out.
When there is no longer sufficient water in the detergent tank, the level indicator lights
up (fig. 6, ref. 5). Stop and fill the tank;
• If the machine is fitted with the optional CHEM DOSE accessory, press the button (fig.
15, ref. 2) to turn the device on, then adjust the detergent mixture to send to the
brushes using the regulation screw (fig. 15, ref. 3). The quantity can be adjusted from
0.5% to 3% per litre of water.
• during work check the cleaning quality and adjust the detergent flow to the brushes by
raising or lowering the lever (fig. 6, ref. 6) as required.
• When using the machine in optional MICRO SCRUB mode, the flow control lever must
be completely lowered (valve closed).
• on certain models, the pressure of the brushes on the work surface can be adjusted
using knob (fig. 14, ref. A)shown in the drawing. To access the knob, lift the dirty water
drum. Turn the knob clockwise to increase the pressure of the brushes on the work
surface, turn it anticlockwise to reduce the pressure of the brushes on the work
surface.
• If you are using the machine in optional MICRO SCRUB mode, make sure the
pressure of the microfibre on the work surface is within the permitted operating range 1 green LED on, minimum pressure; 2 green LEDs on, medium pressure; 3 green
LEDs on, maximum pressure (fig. 6, ref. 17). If the 3 green LEDs and the red LED (fig.
6, ref. 17) come on during operation, you must reduce brush pressure using the
adjustment knob (fig. 14, ref. A) until it is within the permitted pressure value.
Page 16
ENGLISH
16
IMPORTANT
Empty the dirty water drum each time you fill the detergent tank.
Never leave the suction motor on and detergent tap open when parked.
• when the dirty water drum is full, the level indicator comes on (fig. 6, ref. 4) and after a
few seconds the suction motor shuts off. You must stop working and empty the tank.
To restart the suction motor, turn the suction switch (fig. 6, ref. 2) off and then on
again.
• Battery models: if the warning LED (fig. 6, ref. 1) starts flashing, it means that the
batteries are almost flat. After a few seconds the brushes shut down to prevent
excessive discharge of the batteries. Recharge.
At the end of work:
• place the tap lever (fig. 6, ref. 6) in the "CLOSED" position;
• release the brush/drive lever (fig. 6, ref. 7) located under the handgrip. This turns the
brush/drive motor off and the machine stops;
• stop the brush (fig. 6, ref. 3);
• lift the lever (fig. 6, ref. 8) to raise the squeegee from the floor to prevent the
continuous pressure from warping the blades;
• let the suction motor run for at least 2 minutes to make sure it is completely dry, then
press "0" on the suction switch (fig. 6, ref. 2) to switch off the suction motor;
• remove the brushes (or drive disks) to prevent them from warping permanently;
• press the button to turn the optional CHEM DOSE accessory off (fig. 15, ref. 2)
• depending on the model, unplug the machine or disconnect the ANDERSON
connectors (fig. 5, ref. 1 and ref. 2);
• empty and clean the dirty water drum.
6.8. Some useful tips to get the most from your scrubber drier
•
In the event of particularly stubborn dirt on the floor, washing and drying can be
performed in two separate operations.
6.8.1. Prewashing using brushes or pads
• Open the water tap;
• place the brush switch in position "1";
• lower the head;
• operate the drive lever to rotate the brushes;
• make sure the suction motor is off and the squeegee is raised;
• begin washing.
The flow of water must be adjusted in proportion to the desired advance speed. The
slower the machine moves forwards, the less water is needed.
Persist when washing particularly dirty points to give the detergent time to perform its
mechanical action detaching and suspending the dirt and the brushes time to exert an
effective mechanical action.
6.8.2. Drying
Lower the squeegee and with the suction motor on, pass over the same area washed
previously. The result is equivalent to in-depth washing and subsequent ordinary
maintenance will take less time.
To wash and dry at the same time, operate the brush, water, squeegee and suction motor
simultaneously.
Page 17
ENGLISH
17
6.9. Draining the dirty water
! DANGER
Use suitable personal protection devices.
Drain the dirty water with the machine disconnected from the power supply.
The dirty water drum drain hose is at the back left side of the machine.
To empty the drum:
• move the machine near a drain;
• detach the drain hose (fig. 8, ref. 2) from its seat by holding it near the fixing spring (fig.
8, ref. 3) and pulling horizontally;
• keeping the hose end as high as possible, unscrew and remove the cap (fig. 8, ref. 4);
• lower the hose end gradually, controlling the intensity of the flow of water by adjusting
the height from the ground;
• check the amount of dirt left in the dirty water drum and if necessary wash it out. To
facilitate cleaning and complete emptying of the drum, you are recommended to
unfasten and lift it;
• when the dirty water has been totally drained, lower the dirty water drum (if previously
lifted) and refasten to the detergent tank;
• close the drain hose (fig. 8, ref. 2) by replacing the cap (fig. 8, ref. 4), check that it is
tightly closed and replace the hose in its housing.
IMPORTANT
When washing the dirty water drum, never remove the suction filter (fig. 10, ref. 2)
from its housing and never direct the jet of water against the filter itself.
You are then ready to wash and dry again.
6.10. Draining the clean water
! DANGER
Use suitable personal protection devices.
Drain the water with the machine disconnected from the power supply.
To empty the tank:
• move the machine near a drain;
• remove the cap (fig. 9, ref. 1);
• when the detergent tank is completely empty, replace the cap (fig. 9, ref. 1).
i INFORMATION
The water and detergent solution can also be used to wash the dirty water drum.
7.
PERIODS OF INACTIVITY
If the machine is not used for some time, remove the squeegee and brushes (or drive
disks), wash them and put them away in a dry place (preferably in a bag or wrapped in
plastic film) away from dust. Park the machine with the head lowered.
Make sure the tanks are completely empty and perfectly clean.
Disconnect the machine from the power supply (depending on the model, unplug from the
mains or disconnect the ANDERSON connector from the battery wiring).
Battery models: Completely recharge the batteries before storing them. During long
periods of inactivity, you should charge the batteries regularly (at least once every two
months) to keep them constantly at maximum charge.
IMPORTANT
If you do not charge the batteries regularly, they may be irrevocably damaged.
Page 18
ENGLISH
18
8.
BATTERY MAINTENANCE AND CHARGING
! DANGER
Do not check the battery by sparking.
The batteries give off flammable fumes. Put out all fires and hot embers before
checking or topping up the batteries.
Perform the operations described above in a ventilated room.
To avoid permanent damage to the batteries, do not run them down completely.
Remember that when the corresponding red LED (fig. 6, ref. 1) flashes on the control
panel, you must charge the batteries.
8.1. Recharging procedure
• connect the battery charger connector to the battery wiring connector (fig. 5, ref. 1);
IMPORTANT
In the case of gel batteries, use a charger specific for gel batteries only.
• Charge the batteries as described in the battery charger manual;
• at the end of charging, disconnect the connectors;
• reconnect the battery wiring connector to the machine connector.
9.
MAINTENANCE INSTRUCTIONS
! DANGER
Never perform any maintenance operations without first unplugging the machine
from the mains (cable version) or disconnecting the batteries.
Maintenance on the electrical circuit and all other operations not explicitly
described in this manual must be performed by specialised personnel only, in
compliance with current safety legislation and as described in the maintenance
manual.
9.1. Maintenance - General rules
Performing regular maintenance according to the Manufacturer's instructions improves
performance and extends the working life of the machine.
When cleaning the machine, respect the following:
• avoid the use of high pressure washers. Water could penetrate the electrical
compartment or motors leading to damage or the risk of short circuit;
• do not use steam to avoid the heat warping plastic parts;
• do not use hydrocarbons or solvents as they could damage the cowling and rubber
parts.
9.2. Routine maintenance
9.2.1 Suction motor air filter and float switch: cleaning
• Unscrew and remove the tank cap (fig. 10, ref. 1) from the dirty water drum (fig. 10,
ref. 4);
• make sure the dirty water drum (fig. 10, ref. 4) is empty;
• clean the float switch (fig. 10, ref. 5) at the back of the dirty water drum, taking care not
to direct the water jet directly against the float switch;
• remove the suction motor air filter (fig. 10, ref. 2) from the float switch support (fig. 10
ref. 3) inside the dirty water drum at the top;
• clean the filter with running water or the detergent solution used on the machine;
Page 19
ENGLISH
19
• dry the filter thoroughly before replacing it in the support. Make sure the filter is
correctly located in its housing;
• screw the cap back on the dirty water drum.
9.2.2 Basket filter: cleaning
• Remove the basket filter from the water fill hole at the front of the machine;
• clean the filter with running water or the detergent solution used on the machine;
• replace the filter back in its housing, making sure it is correctly positioned.
9.2.3 Detergent filter: cleaning
• Unscrew the screw located below the bottom tank (fig. 11, ref. 1);
• unscrew the detergent filter (fig. 11, ref. 2);
• clean the filter with running water or the detergent solution used on the machine;
• replace the filter back in its housing, making sure it is correctly positioned and retighten
the screw.
9.2.4 Squeegee blades: replacing
The squeegee blades collect the film of water and detergent from the floor and prepare
the way for perfect drying. With time, the constant rubbing leaves the edge of the blade
in contact with the floor rounded and cracked, reducing the drying efficiency and requiring
it to be replaced.
Turning or replacing the blades:
• lower the squeegee by means of the corresponding lever (fig. 6, ref. 8);
• remove the squeegee (fig. 2 ref. 6) from its mount (fig. 7 ref. 2) by completely
unscrewing the two knobs (fig. 7 ref. 3)
• remove the suction hose sleeve (fig. 7, ref. 4) from the squeegee;
• release the catch (fig. 12 ref. 3 or 6);
• remove the two blade retainers (fig. 12 ref. 2 or 7) by first pushing them towards the
body of the squeegee (fig. 12 ref. 1) then extracting them;
• remove the blade (fig. 12 ref. 4 or 5);
• reuse the same blade by reversing the edge in contact with the floor until all four edges
are worn out, or replace with a new blade, fitting it onto the screws on the body of the
squeegee (fig. 12 ref. 1);
• reposition the two blade retainers (fig. 12 ref. 2 or 7) by centring the widest part of the
slots over the fixing screws on the squeegee body (fig. 12 ref. 1), then pushing the
blade retainers inwards;
• refasten the catch (fig. 12, ref. 3 or 6).
Replace the squeegee in its support following the instructions in paragraph 6.2.
9.2.5 Fuses: replacement (battery models)
The fuses protecting the brush and suction motors are located in the fuse holder (fig. 13,
ref. 1) attached to the dirty water drum above the machine battery compartment.
To replace the fuses:
• make sure the dirty water drum is empty and empty if necessary;
• raise the dirty water drum;
• raise the fuse holder cover and remove the fuse by unscrewing the fixing screws;
• fit a new fuse and close the fuse holder cover;
• lower the dirty water drum.
Fuse table: For the complete fuse table, see the spare parts catalogue.
IMPORTANT
Never use a fuse with a higher amperage than specified.
Page 20
ENGLISH
20
If a fuse continues to blow, the fault in the wiring, boards (if present) or motors
must be identified and repaired. Have the machine checked by qualified
personnel.
9.3. Routine maintenance
9.3. 1.
Daily operations
After each day's work, proceed as follows:
• disconnect the machine from the power supply;
• empty the dirty water drum and clean if necessary;
• clean the squeegee blades and check for wear. If necessary, replace.
• check that the suction hole in the squeegee is not blocked. If necessary remove
encrusted dirt;
• Battery model: recharge the batteries according to the procedure described.
9.3.2. Weekly operations
• Clean the dirty water drum float switch and make sure it is working correctly;
• clean the suction air filter and make sure it is undamaged. If necessary, replace.
• clean the detergent filter at the front opening of the detergent tank (fig. 2, ref. 7) and
check that it is not damaged (replace if necessary);
• clean the suction hose;
• clean the dirty water and detergent tanks;
• Battery model: check the level of battery electrolyte and top up with distilled water if
necessary.
9.3.3. Six monthly operations
Have the electrical circuit checked by qualified personnel.
Page 21
ENGLISH
21
10.
TROUBLESHOOTING
10.1. How to resolve possible problems
[B]= battery machines
[C]= cable machines
[BT]= battery machines with electric drive
Possible problems affecting the whole machine.
PROBLEM CAUSE REMEDY
The machine does not function
• [B]= battery connector
disconnected
• [B]= connect the batteries to
the machine
• [B]= the batteries are flat
• [B]= recharge the batteries
• [C]= the machine is not plugged
into the mains socket
• [C]= plug into the mains
socket
The brushes do not turn
• [B]= place the brush switch in
the "0" position;
• [BT]= you have not used the
brush switch
• place the brush switch in the
"1" position;
• press the brush switch
• you have not pressed the brush
lever
• press the brush lever
• [B]= the motor thermal cutout
has tripped; the motor is
overheated
•
[B]= release the brush lever,
turn the brush switch to the "0"
position (off); leave the
machine to cool down for at
least 45'
• [B], [BT]= the power supply or
motor thermal cutout connectors
are disconnected
• [B], [BT]= reconnect the
power supply or motor
thermal cutout connectors
• [C]= the motor power supply
connector is disconnected
• [C]= reconnect the motor
power supply connector
• [B] [BT]= the brush motor
fuse has blown
• [B] [BT]= have someone
check and eliminate the
causes responsible for the
blown fuse, then replace
• [B] [BT]= the batteries are flat
• [B] [BT]= recharge the
batteries
• the reduction unit is faulty • have the reduction unit
replaced
• the motor is faulty • have the motor replaced
The brush motor has trouble in
starting (cable models only)
• you are working with a dry brush
on a very rough floor
• open the detergent tap
• you are working with power
cable extensions with an
inadequate section, or the
voltage is considerably lower
than the rated value for the
scrubber as shown on the rating
plate (15% less)
• avoid the use of
inappropriate extensions.
Increase the section of the
electric wires and locate
sockets with a higher voltage
• the motor is faulty • have the motor replaced
The machine does not clean
evenly
• the brush or disks are worn • replace
Page 22
ENGLISH
22
No detergent is delivered
• the tap lever is in the "CLOSED"
position
• move the lever to the
"OPEN" position
• the detergent tank is empty • fill it
• the hose delivering the
detergent to the brush is
blocked
• unblock and open the circuit
• the tap is dirty or faulty • clean or replace the tap by
unscrewing the screw (ref.
1 fig. 11)
The detergent flow does not
stop
• the tap stays open, because it is
damaged or very dirty
• have the tap cleaned or
replaced
The suction motor does not
start
• the suction switch is in the ‘0'
position (off)
• turn the suction switch on
• there is no power to the suction
motor or the motor is faulty
• check that the motor power
connector is correctly
connected to the main
wiring; in the second case
have the motor replaced
• [B] [BT]= the fuse has blown
• [B] [BT]= replace the fuse
The squeegee does not clean
or suction is ineffective
• the edge of the rubber blades in
contact with the floor is worn
• replace the rubber blade
• the squeegee or hose is
blocked or damaged
• unblock and repair the
damage
• the float switch has tripped (dirty
water drum), is clogged by dirt or
broken
• empty the dirty water drum
or reset the float switch
• the suction hose is blocked • unblock the hose
• the suction hose is not
connected to the squeegee or is
damaged
• connect or repair the hose
• there is no power to the suction
motor or the motor is faulty
• check that the motor power
connector is correctly
connected to the main wiring
and that the fuse is not
blown; in the second case
have the motor replaced
The machine does not move
• there is no power to the
brush/drive motor or it is faulty
• in the first case, place the
brush switch in the "1"
position and press the
brush/drive lever; in the
second case, check that the
brush/drive motor is correctly
connected to the main wiring;
in the third case replace the
motor
CT90, drive motor electronic
board protection activated,
check the type of alarm
present on the board (see
chapter 11)
• the reduction unit is broken
(therefore the brush does not
turn)
• have the reduction unit
replaced
• the brush motor thermal cutout
has tripped; the motor is
overheated
• stop the machine, turn it off
and leave it to cool for at
least 45'
• [B] [BT]= the batteries are flat
and the brushes have shut down
• [B] [BT]= recharge the
batteries
Page 23
ENGLISH
23
The machine tends to pull to
one side
• the direction adjustment knob
must be adjusted appropriately
for the floor
• regulate the direction of
movement by adjusting the
direction adjustment knob
The batteries do not provide
the normal work time (battery
models only)
• the battery poles and charging
terminals are dirty and oxidised
• clean and grease the poles
and terminals, recharge the
batteries
• the electrolyte level is low • top up all the elements with
distilled water as described in
the instructions
• the battery charger does not
work or is unsuitable
• see battery charger
instructions
• there are considerable
differences in density between
the various elements of the
battery
• replace the damaged battery
• you are using the machine with
excessive pressure on the
brushes
• reduce pressure on the
brush
• there are considerable
differences in density between
the various elements of the
battery
• replace the damaged battery
The battery discharges too fast
during use, even though it has
been charged correctly and
when tested with a hydrometer
at the end of recharging, it
turned out to be uniformly
charged (battery models only)
• the battery is new and does not
deliver 100% of its expected
capacity
• the battery must be "run-in"
by performing 20-30 charges
and discharges to obtain
maximum performance
• the machine is being used at
maximum capacity for
continuous periods and the
working time is not sufficient
• if possible, use batteries with
a higher capacity or replace
the batteries with others
charged previously
• the electrolyte has evaporated
and does not cover the plates
completely
• top up all elements with
distilled water until the plates
are covered then recharge
the battery
The battery discharges too fast
during use, recharging with an
electronic battery charger is
too fast and after recharging
the battery supplies the right
voltage (about 2.14V for each
element without load), but
when tested with a hydrometer
is found not to be uniformly
charged (battery models only)
• the battery supplied filled with
acid by the Manufacturer has
been stored for too long before
being recharged and used for
the first time
• if recharging with a normal
battery charger is not
effective, you must use a
double recharging cycle:
- charge slowly over a 10 hour
period at a current of 1/10 the
nominal capacity for 5 hours
(e.g. for a 100Ah(5) battery
the current must be set at
10A, using a manual battery
charger);
- rest for one hour;
- charge with the normal
battery charger.
Page 24
ENGLISH
24
At the end of charging with the
electronic battery charger, the
battery does not provide the
correct voltage (about 2.14 V
per element without load) and
appears to be uniformly not
charged when tested with a
hydrometer (battery model
only)
• the battery has not been
connected to the battery charger
(for example, because the low
voltage connector of the battery
charger has been erroneously
connected to the machine
connector)
• connect the battery charger
to the battery connector
• the battery charger and power
socket to which the battery is
connected are not compatible
• check that the power supply
characteristics indicated on
the battery charger rating
plate comply with those of the
mains power supply
• the battery charger has not
been installed correctly
• taking the actual voltage
available at the socket into
account, make sure that the
connections of the primary of
the transformer inside the
battery charger are correct
(consult the battery charger
manual)
• the battery charger is not
working
• make sure there is voltage to
the battery charger, that the
fuses are not blown and that
the current reaches the
battery; try charging with
another rectifier. If the battery
charger is not working,
contact the technical service
centre and indicate the serial
number of the battery charger
At the end of charging with the
electronic battery charger, the
battery does not provide the
correct voltage (about 2.14 V
per element without load) and
only one or a few elements are
found to be discharged when
tested with a hydrometer
(battery model only)
• one or more elements are
damaged
• replace the damaged
elements if possible.
For 6 or 12 V single block
batteries, replace the entire
battery
The electrolyte in the battery is
turbid (battery models only)
• The battery has reached the
end of the charging/discharging
cycles declared by the
manufacturer
• replace the battery
• the battery has been recharged
with too high a current
• replace the battery
• the battery has been charged
beyond the limit suggested by
the Manufacturer
• replace the battery
Page 25
ENGLISH
25
ALARMS ON THE DISPLAY
1) ACC "drive lever" already pressed when the machine is turned on or after an Emergency
2) SIC Emergency button pressed
3) POT Speed potentiometer fault
4) MOS Board (mosfet) short circuit
5) HOT Motor thermal cutout tripped
6) LIM Board (mosfet) thermal limitation problem
7) BLT Drive block. Appears when the battery voltage is too low and the drive is blocked.
8) AcS Brush Control Fault Appears when there is a fault in the solenoid switch controlling
the brushes.
9) AcA Suction control fault. Appears when there is a fault in the solenoid switch controlling
suction.
10) FuP Fuse. Appears when the fuse is blown.
Board alarms CLEANTIME 90/MICRO SCRUB
If drive is interrupted, the error code should be identified by means of the status LED (fig. 6. ref. 16).
In the absence of malfunctions, the status LED is steadily on while the machine is in operation. If a
malfunction is detected, the status LED provides two types of information, a slow flash (2 Hz) or a
rapid flash (4 Hz) to indicate the severity of the malfunction.
Malfunctions with a slow flash are cancelled automatically once the malfunction has been repaired
and the machine functions normally again. Malfunctions with a rapid flash ("*" in the table) are
considered more serious. The machine must be turned of using the key switch (fig. 6 ref. 14) to
reset operation after repairing the malfunction.
The indication of severity remains active for 10 seconds, after which the status LED flashes
constantly showing a two digit malfunction code until the repairs have been carried out.
For example, error code "1,4" is displayed as follows:
☼ ☼☼☼ example alarm code 1,4
LED CODES DESCRIPTION
1,1 ☼ ☼ Overheating > 92°
1,2 ☼ ☼☼ Accelerator malfunction
1,3 ☼ ☼☼☼ Speed limiter potentiometer malfunction
1,4 ☼ ☼☼☼☼ Overvoltage malfunction
1,5 ☼ ☼☼☼☼☼ Undervoltage malfunction
2,1 ☼☼ ☼ Principal contactor actuator opening failure
2,3 ☼☼ ☼☼☼ Principal contactor actuator closing failure
2,4 ☼☼ ☼☼☼☼ Principal contactor actuator closing failure
* 3,1 ☼☼☼ ☼ Accelerator potentiometer malfunction
3,2 ☼☼☼ ☼☼ Brake activation malfunction
3,3 ☼☼☼ ☼☼☼ Low battery voltage
3,4 ☼☼☼ ☼☼☼☼ Brake deactivation malfunction
3,5 ☼☼☼ ☼☼☼☼☼ HPD malfunction (incorrect regulation of accelerator
potentiometer)
* 4,1 ☼☼☼☼ ☼ Motor short circuit
* 4,2 ☼☼☼☼ ☼☼ Incorrect motor voltage/short circuit in motor
* 4,3 ☼☼☼☼ ☼☼☼ EEPROM malfunction
* 4,4 ☼☼☼☼ ☼☼☼☼ Short circuit in motor/EEPROM error
Loading...