COMMERCIAL
https://harrissupplyind.com - To Order Parts Call 608-268-8080
14” and 16”
UPRIGHT VACUUM
OPERATIONS & PARTS MANUAL
REV A
March 2004
If you observe the recommendations listed below,
this will ensure maximum performance by the
appliance, the longest possible life and a high level
of safety.
• Do not clean the appliance with solvents - the body and
accessories are in plastic and, therefore, may get damaged.
• Never immerse the appliance in water.
• Do not clean the appliance in water.
• Do not leave the appliance unattended while it is running.
• Never put the appliance near to heat sources.
• Remove the power plug from the power socket after each
use of the appliance.
• If the power lead and power socket are damaged, replace
them immediately at an authorized service center.
• Do not use the appliance as a liquid-suction device.
• Before every maintenance or replacement job, remove the
appliance’s power plug from the power socket.
• Do not suck in lighted cigarette ends or flammable
materials.
• Remove the plug by pulling the plug body and not the
power lead.
• Strictly use original dust-bags and filters.
NOTE
The manufacturer reserves the right to make any
modifications without prior notice.
IMPORTANT!!
Before attempting any maintenance job, always remove the power plug.
For all maintenance jobs, always contact our authorised service centers.
https://harrissupplyind.com - To Order Parts Call 608-268-8080
PAGE 1
CONNECTING THE HOSE
Insert the rotating sleeve into the bag-holding sleeve, insert the second rotating sleeve into the telescoping element, and hook the hose to the handle.
COMMERCIAL
1 Ergonomic handle
2 Power cord
3 Hose
4 Telescoping extension
5 Switch
6 Carrying handle
7 Cord winding device
8 Cover
9 Vent grid
10 Container
11 Engine housing
12 Electric brush
13 Base
14 Hi/Low vac motor switch
OPERATING THE TELESCOPING EXTENSION
Extend the telescoping extension by pulling it; block it by turning
the dedicated ring nut counter-clockwise.
SYSTEM START-UP
https://harrissupplyind.com - To Order Parts Call 608-268-8080
13
1
4
14
6
7
9
12
2
3
5
8
10
11
PAGE 2
STARTING THE BRUSH
Put your foot on the PUSH sign and tilt the vacuum-cleaner body.
FILTER FULL INDICATOR
If the “bag full” gauge turns red, please verify:
a) whether the dust bag is full, or
b) whether the brush is clogged, or
c) whether the vacuuming hose is clogged;
in these cases, remove the obstruction
d) whether the Hepa filter is fully clogged.
It is normal that during vacuuming the “bag full” gauge partially turns red,
because the hose is closed.
CHECKING THE BRUSH
The brush-checking device continuously monitors the operation of the brush:
Green light: the brush is working correctly
Red light: the brush is either blocked or it is undergoing excessive stress.
Turn the machine off, detach the plug from the mains, and look for the cause
of the blocking.
REPLACING THE FILTER BAG
Remove the cover.
Place the dust bag into the container, by inserting the bag-holding sleeve into
the dust bag hole and by pushing the safety ring all the way in.
If the filter bag is not placed correctly, closing the cover will be impossible.
MAINTENANCE
https://harrissupplyind.com - To Order Parts Call 608-268-8080
PAGE 3
REMOVING CLOGGING DEBRIS FROM THE OUTER DUCT
Any material clogging the duct can be removed by extracting the telescoping
extension from its seat, operating the vacuuming function, and intermittently
opening and closing the vacuuming by hand.
Do not insert objects into the duct in order to remove any clogging.
A
REPLACING THE FILTER
Pull out the filter holder and replace the filter, or clean it by tapping it lightly
(replace it approximately every 20 bags).
REPLACING THE HEPA FILTER;
REPLACING OR CLEANING THE PRE-FILTER
Pull latch “A” in order to unhook the vent grid; at the same time, slide it
(in the direction shown by the arrow) so that it comes free. The pre-filter is
housed in the air exhaust under the Hepa filter. Replace the pre-filter or clean
it, by washing it with water; dry it and carefully replace it in its housing.
Assemble the Hepa filter and the vent grid again, by sliding it all the way in
until you hear the latch snapping into place.
REMOVING CLOGGING DEBRIS FROM THE INNER DUCT
Lay the vacuuming body down horizontally, flush with the electric brush.
Unscrew the base screws, remove the base.
Remove any clogging material from the duct by using a flexible cleaning rod.
https://harrissupplyind.com - To Order Parts Call 608-268-8080
PAGE 4
REPLACING THE ROLLER
Unscrew the base screws, remove the base, and remove the roller by sliding
the holders off.
Insert the roller, paying attention to the correct installation of both the roller
holders into their seats and of the belt, keeping it in the guide on the engine
pulley first and then on the roller pulley. Reassemble the base.
INSTALLING THE VAC MOTOR
Place the rubber block of the engine holder onto its dedicated, oriented supporting element. Place the engine over it, rotating it until you find the correct
joint into its seat. Install the first grommet ring on the engine, then the spacer,
and finally the second grommet ring.
In order to disassemble the vac motor housing, remove the dust bag cover,
unhook the vent grid and unscrew the four screws from the shell.
REMOVING THE ELECTRIC BRUSH COVER
Unscrew the screws from the bottom and remove the cover.
https://harrissupplyind.com - To Order Parts Call 608-268-8080
PAGE 5
REPLACING THE ELECTRONIC BOARD
Slide the board off the guides and detach the connection.
Disconnect the supply wires from the terminal and replace the board.
DISASSEMBLING THE JOINT
Unscrew the case screws.
Lift the cover and free the joint.
Unscrew the cable-holder screws from the vacuuming device.
Slide the joint off.
Unscrew the cable-holder screws from the electric brush and free the
board wires.
Slide the joint off the cable.
IMPORTANT!!
Before attempting any maintenance job, always detach the power plug from
the mains.
For all maintenance jobs, always contact our authorized service center.
https://harrissupplyind.com - To Order Parts Call 608-268-8080
PAGE 6
SPARE PARTS
1 - Hepa filter
2 - Air freshener
3 - Filter bag
4 - Filter
5 - Pre-filter
1
ACCESSORIES PROVIDED
1 - Small brush
2 - Crevice tool
3 - Curved sleeve
4 - Hose
5 - Telescoping extension
SPECIFICATION
Vacuum motor power
Brush motor power
Dust bag capacity
Working surface
Weight
Noisiness level (at operator ear)
Voltage
Electronic card, motor blocking
14”
1000 W
150 W
6,5 l
350 mm
6,94 Kg
Provided
16”
1000 W
150 W
6,5 l
400 mm
7,04 Kg
Provided
The manufacturer reserves the right to make any modification without prior notice.
Specifications subject to change without notice.
EAGLE POWER PRODUCTS GROUP - ph. 1-800-486-2775
ELECTRIC DIAGRAM
Caution!
Any job involving the electric plant
must be carried out only by qualified
personnel.
120 Volt / 60 Hz
min 67,25 dBA / max 69,75 dBA
https://harrissupplyind.com - To Order Parts Call 608-268-8080
2
3
2
5
3
1
4
4
5
PAGE 7
Reference
Y
https://harrissupplyind.com - To Order Parts Call 608-268-8080
Number
1
2
COMMERCIAL 14 & 16 VACUUM ASSEMBL
Part Number Description Qty
VCSA1GUV0 HOUSING, VACUUM 1
USE KIT VC2000 SCREW 4
3
4/7
8
9
10+11
12
12
13
14
15
16
17
18
19
VCSA1PORTBBU
VCSA3MAWCC
VCA8LAMO CLIP, BRASS 1
USE KIT VC2000 SCREW 1
VCA1CWEGC COVER, UPPER, LIGHT GRAY 1
VCA1TAPDX RIGHT INSERT, BACK COVER 1
VCA1TAPSX LEFT INSERT, BACK COVER 1
VCA7FIP
VCA1VP
VCA3PF
USE KIT VC2000 SCREW 2
USE KIT VC2000 SCREW 7
VCA1SICS NO BAG SAFETY LOCK OUT RING 1
VCA8MOSISA SPRING, LOCK OUT RING 1
**
**
**
**
**
BACK COVER, COMPLETE W/GASKET 1
MOTOR, VACUUM, COMPLETE 1
FILTER, INNER 1
FILTER HOLDER, INNER, RED 1
AIR FRESHENER STICK 1
PAGE 8
Reference
Y
https://harrissupplyind.com - To Order Parts Call 608-268-8080
Number
COMMERCIAL 14 & 16 VACUUM ASSEMBL
Part Number Description Qty
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
VCSA1INDNE
VCA1MASAGS SLEEVE, DARK GRAY 1
VCA1ANMGS RING, SLEEVE, DARK GRAY 1
VC1000
VCA1MAGINE
VCA2TESC46
VCA4PNE
VCA4LNE
VCA1MACUNE
VCSA4PT
VCA2COSIL GASKET, HEPA FILTER 1
VCSA7FH1
VCSA1GFCOMM GRILL, FILTER, COMPLETE 1
VCA7PFCOM
VCA1SUPF HOUSING, HEPA FILTER 1
USE KIT VC2000 SCREW 1
USE KIT VC2000 SCREW 5
USE KIT VC2000 SCREW 1
VCA1CAFCNE CLAMP, CORD 1
**
**
**
**
**
**
**
**
**
**
FULL BAG INDICATOR, BLACK 1
BAG, PAPER 1
HOSE CUFF, BLACK 2
HOSE, L=18" 1
ROUND BRUSH TOOL, BLACK 1
CREVICE TOOL, BLACK 1
TUBE, CURVED 1
WAND, TELESCOPING, BLACK 1
FILTER, HEPA 1
PRE-FILTER, HEPA 1
38
39
40
41
42
43
44
45+47
46
48
49
50
51
52
TBD
**
VCA1AIGS CORD WRAP, LOWER, DARK GRAY 1
VCA3CABCOP-1 WIRING, INNER, L=25" 1
VCA1SM COVER, FRONT 1
VCA1CABC CLAMP, CORD 1
USE KIT VC2000 SCREW
VCA1TOR NUT, BLOCK 1
VCA1CLIPGS CLIP, WAND AND TOOL 2
USE KIT VC2000 SCREW 4
USE KIT VC2000 SCREW 1
VCSA1IMPC HANDLE HAND GRIP, COMPLETE 1
USE KIT VC2000 SCREW 1
VCA1GUCA CORD SLIDE 1
VCA6TCC CHROME PLATED BAR 1
VCA2GORG RUBBER SLACK ABSORBER 1
VCA1PUMGR BUTTON, HANDLE, DARK GRAY 1
VCA8MPUM SPRING, HANDLE BUTTON 1
VCA1SMPGR BUTTON SPRING HOLDER, DARK GREY 1
CIRCUIT BOARD, VAC MOTOR REGULATION 1
PAGE 8
Reference
Y
https://harrissupplyind.com - To Order Parts Call 608-268-8080
Number
COMMERCIAL 14 & 16 VACUUM ASSEMBL
Part Number Description Qty
53
54
55
56
57
58
VCA3INTR
VCA3INTN
VCA1MPWHSGRCU COVER, SWITCH 1
VCA8LAMO1 PLATE 1
USE KIT VC2000 SCREW 1
VCA3CA3NEUS
VC2000 HARDWARE KIT FOR VACUUM ASSEMBLY
**
**
**
Recommended Stocking Item
**
RED BIPOLAR SWITCH, WITH LIGHT 1
BLACK SWITCH, HI-LOW 1
POWER CORD, BLACK, 50' 1
PAGE 9
COMMERCIAL 14 & 16 BASE ASSEMBL
Y
https://harrissupplyind.com - To Order Parts Call 608-268-8080
Reference
Number
1
2 USE KIT VC2001 SCREW 3
3 USE VCSA4RSP14N OR TBD RIGHT SIDE PLATE, ROLLER BRUSH 1
4 USE VCSA4RSP14N OR TBD BEARING 2
5
6 USE VCSA4RSP14N OR TBD LEFT SIDE PLATE, ROLLER BRUSH 1
VCA1BAS350 BASE, 14" 1
TBD BASE, 16" 1
USE VCSA4RSP14N ROLLER BRUSH 14" 1
USE TBD ROLLER BRUSH 16" 1
Part Number Description Qty
3-6
7 VCA2CP
8
9
10 VCA2PASB GROMMET, CORD 1
11 VCA3CABBCUS BASE CORD 1
12 VCA1R57
VCSA4RSP14N
TBD
**
**
VCA1CARGR3 14" CASE, DARK GRAY 1
TBD 16" CASE, DARK GRAY 1
VCA2GUPANE 14" BUMPER, DARK GRAY 1
TBD 16" BUMPER, DARK GRAY 1
**
**
14" COMPLETE ROLLER BRUSH 1
16" COMPLETE ROLLER BRUSH 1
BELT, POLY V 1
WHEEL 2
PAGE 9
Reference
Y
https://harrissupplyind.com - To Order Parts Call 608-268-8080
Number
COMMERCIAL 14 & 16 BASE ASSEMBL
Part Number Description Qty
13 VCA1PER
14 VCSA1MICG
15 VCA1CMICG COVER, MICROSWITCH 1
16 USE KIT VC2001 SCREW 1
17+22 VCSA1CFSNEG TOP COVER WITH WINDOW 1
18 USE KIT VC2001 SCREW 4
19 USE KIT VC2001 SCREW 2
20 VCA1CABCC CLAMP, CORD 1
21 VCSA3SEG2 CIRCUIT BOARD, 120 VOLT 1
22 VCA1VETGBE WINDOW 1
23 VCA1SMPA MOTOR SUPPORT, REAR 1
24 VCSA3MT2AC
25 VCA1SMAA MOTOR SUPPORT, FRONT 1
26 VCA8PULM PULLEY, MOTOR 1
27 VCA3CAMT
28 VCA8MCMT
29 USE KIT VC2001 SCREW 2
30 VCA1BFSNCUS CORD FASTENER, JOINT 1
31 VCA8SNO JOINT 1
32 VCA2PASSC PROTECTIVE SLEEVE, WIRE 1
34 USE KIT VC2001 WASHER 2
VC2001 HARDWARE KIT FOR BASE ASSEMBLY
**
**
**
**
**
PIN, WHEEL 2
MICROSWITCH, COMPLETE 1
MOTOR, BRUSH COMPLETE 1
MOTOR CARBON BRUSH 2
MOTOR CARBON SPRING 2
Recommended Stocking Item
**
PAGE 9
Warranty Policy
https://harrissupplyind.com - To Order Parts Call 608-268-8080
Limited Warranty
Eagle Power Products (EPP) warrants new cleaning equipment against defects in material and
workmanship under normal use and service to the original purchaser as detailed below.
10 Years
Subject to the conditions stated below, EPP warrants polyethylene tanks and housings to be
free from defects in materials and workmanship for a period of ten years.
3 Years
Subject to the conditions stated below, EPP warrants all automatic scrubber components to
be free from defects in materials and workmanship for a 3-year period. Parts replaced or
repaired are warranted for the remainder of the original warranty period.
1 Year
Subject to the conditions stated below, EPP warrants all other cleaning equipment
components to be free from defects in materials and workmanship for a 1-year period. Parts
replaced or repaired are warranted for the remainder of the original warranty period.
Batteries are prorated for one year.
EPP will furnish and charge for replacement parts, including transportation, to the original
owner through an EPP authorized service center. If the part is returned within 30 days and is
found defective, the owner will be credited for the cost of the replacement part including
shipping and handling.
Labor charges are covered for one year from the date of purchase if provided by an authorized
EPP service center. Travel is covered for 90 days for battery operated equipment only.
Wear items exempt from warranty include belts, carbon brushes, power cords, wheels, pad
drivers, clutch plates, brushes, pads, handle grips, filters, screens, throttle cables, and squeegees.
This warranty shall not apply to failures caused by misuse or abuse, improper
maintenance as stated in the operation manuals, use of unauthorized repair parts, repairs
by other than an EPP authorized service center, and damage in transit.
EPP disclaims and denies any liability for any direct, indirect, special incidental or consequential damage which may
be suffered as a result of sale, delivery, servicing, use, loss of any product, downtime, labor, freight, or other charges
not expressly included herein.
Date Purchased:
Model Number:
Serial Number:
Please be sure to record this information. This information will be necessary for future warranty claims.
Eagle Power Products Sales and Service Provided by:
1174 Northland Drive Mendota Heights, MN 55120
651.686.5399 Fax 651.686.5695
www.eaglepower.com
Loading...