IO-Power APM-101R, APM-102R, APM-103R, APM-101RH, APM-102RH User Manual

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

IO-Power Technology

Outdoor MIMO Wireless Access Point

APM-101R / APM-102R / APM-103R

APM-101RH / APM-102RH / APM-103RH

User Manual

201111 v1.1

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Chapter 1: Product Overview ............................................................................................................................................. 4

Introduction ................................................................. 4

Flexible wireless backbone deployment options ............................................................................................................. 5

High-performance wireless backbone .............................................................................................................................. 5

Secure and efficient client connectivity ............................................................................................................................. 5

APM-100R(H) Category ...................................................................................................................................................... 5

Installation ................................................................... 6

Package Contents ...................................................... 7

Chapter 2: System Configuration ...................................................................................................................................... 8

Access the Browser-Based Utility............................ 8

System Setup ............................................................. 9

System Setup > Basic Setup .................................... 9

System Setup > Network Setup ............................. 10

IP Setup ............................................................................................................................................................................... 10

Spanning Tree Protocol .................................................................................................................................................... 10

Ethernet Link Speed .......................................................................................................................................................... 11

DHCP Server Setting ......................................................................................................................................................... 11

Management VLAN ........................................................................................................................................................... 11

Wireless ..................................................................... 12

Wireless > Radio Setup........................................... 12

Wireless > WLAN Setup ......................................... 13

Wireless > Wireless Security .................................. 15

Wireless > WMM Setup........................................... 17

Wireless > Bandwidth Control ................................ 17

Administration ........................................................... 18

Administration > Management ............................... 18

Administration > Login Password .......................... 19

Administration > SNMP Setup ............................... 19

Contents

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

SNMP V3 ............................................................................................................................................................................. 19

RW User Name Read and write authority login ID. ...................................................................................................... 20

RO User Name Read only authority login ID. ................................................................................................................ 20

SNMP V2C .......................................................................................................................................................................... 20

Utility........................................................................... 20

Utility > Ping .............................................................. 21

Utility > RSSI Calculator .......................................... 21

Utility > Fresnel Zone .............................................. 22

Utility > Antenna Alignment Tool ........................... 22

Link Test .............................................................................................................................................................................. 23

Utility > Site Survey .................................................. 24

Status ......................................................................... 24

Status > System Information .................................. 24

Status > System Status ........................................... 25

Channel The channel used by the wireless interface. .................................................................................................. 25

Status > Connecting Nodes Information ............... 26

Status > Connecting AP Information ..................... 26

Appendix 1: Specifications................................................................................................................................................ 27

Hardware Specification ........................................... 27

Software Specification ............................................. 32

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Chapter 1: Product Overview

Product

Images

Model Name

APM-101R (H)

APM-102R (H)

APM-103R (H)

Rear Side

Top of Antenna

Connector

Below of

Antenna

Connector

Front Side

Introduction

The APM-100R(H) series are enterprise and carrier-grade 802.11N Outdoor Wireless Access Point
which offers customer a robust and high performing solution for PTP/PTMP/Hotzone applications in
both license-free 2.4GHz and 5GHz bands.
The APM-103R is the most ideal candidate for Service Providers looking to deliver carrier-grade
wireless services to multiple market segments such as campuses, hospitality, healthcare,
warehousing and wider metropolitan area deployments.
Designed to meet customer needs in a broad range of industries, the APM-100R(H) offer the following

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

benefits :

Flexible wireless backbone deployment options

Multiple radio interfaces were integrated by IO-Power’s core data switching technology inside the
APM-100R(H) series. Each radio interface can be configured independently to meet different wireless
connectivity purposes. With the fast data switching between multiple radio interfaces, the backbone
throughput will remain in a high level even after several relays between APs.

High-performance wireless backbone

With the next generation 802.11N MIMO technology, the APM-100R(H) offer data link rate up to
300Mbps in each single radio interface. Short Guard Interval and Frames Aggregation methodology
configurations improve the efficient of backbone usage.

Secure and efficient client connectivity

The nimble QoS (Quality of Service) configuration provides flexible management of user’s access
bandwidth of wireless connectivity. Perfect integrated with central RADIUS server and data encryption
technique, the APM-100R(H) series provide a secure wireless connectivity for each client device.

APM-100R(H) Category

Model

Radio Spec.

Radio Amount

APM-101R

Dual-Band 2x2 MIMO Normal Power

1

APM-102R

Dual-Band 2x2 MIMO Normal Power

2

APM-103R

Dual-Band 2x2 MIMO Normal Power

3

APM-101RH

Dual-Band 2x2 MIMO High Power

1

APM-102RH

Dual-Band 2x2 MIMO High Power

2

APM-103RH

Dual-Band 2x2 MIMO High Power

3

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Installation

The APM-100R(H) series product has up to 3 dual-band 2X2 MIMO radio interfaces. Each 2X2 MIMO
radio interface will has 2 N-type connectors come out on the waterproof housing. We strongly
recommend that check antenna attachment to match your configuration before the installation.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

A PoE is the power supply of the APM-100R(H) series. Please connect the ETH1+Power port to the
included PoE injector by Ethernet cable.

Connect another data port on the PoE injector to your LAN switch or PC, if necessary.

Package Contents

● APM-100R(H) 802.11A/G/N Outdoor Wireless Bridge

● PoE Power Injector

● Power Adapter

● Mounting Kit & Screw

● CD: User Manual

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Chapter 2: System Configuration

Access the Browser-Based Utility

To access the system web user’s interface, launch the web browser on your computer, and enter the

device IP address in the Address field of the web browser. (The factory default IP address is

192.168.1.1.) Then press Enter.

A login screen will appear. Go to the login page by Click the “Home > Login” in sub-menu. Login ID
and password is required before access the system web user’s interface. The default administrator’s

ID is

admin

and password is

admin

. For normal user’s login ID is

user

and password is

user

.

Configuration will be not available for user account.

The configuration page was vertically divided into right and left part. Items in the left part show the
concurrent configuration corresponds to the items in right part.

Please do remember to click the

Apply

button on the very bottom of every page to make your
configuration changes effected; otherwise the changes you just made will be ignored once you leave
the current page. You can also click the

Cancel

button to regret the changes.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

System Setup

A

System Setup

includes device related elements, such as system time and IP setting.

System Setup > Basic Setup

Language The APM-100R(H) series WEB GUI is designed to support English and Chinese language

in display. Users can choose the proper language in language list.

Device Name User would like to give a name for identifying a particular outdoor access point in here.

System Date User would like to set the date manually in this item.

System Time User would like to set the time manually in this item.

Time Synchronization Time synchronization setting will decide the duration to next time

synchronization. When any NTP server is available in network, user can enable the NTP and system
will automatically synchronize system time with NTP server.

GMT Time zone Set a Greenwich Mean Time setup for time synchronization.

Time Server User can insert an available IP address of NTP server in Internet for time

synchronization.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

System Setup > Network Setup

IP Setup

IP Assignment System allows you to assign the device IP address dynamically from existing DHCP

server or set a static IP address manually.

IP Address Once Static IP was selected, the IP Address field will allow you to set the bridge device IP

address manually. This IP address of the bridge is used as the base for all of your local network
settings.

Subnet Mask This is the subnet mask address for your bridge device. Set the IP subnet mask

manually.

Default Gateway Set the default gateway IP address manually.

DNS 1 & 2 The Domain Name System (DNS) is how the Internet translates domain or website names

into Internet addresses or URLs. Your ISP will provide you with at least one DNS Server IP Address. If
you wish to use another, enter that IP Address in DNS 2 field.

Spanning Tree Protocol

STP The Spanning Tree Protocol (STP) is a network protocol that ensures a loop-free topology for any

bridged Ethernet local area network. The basic function of STP is to prevent bridge loops and ensuing
broadcast radiation. Spanning tree also allows a network design to include spare (redundant) links to
provide automatic backup paths if an active link fails, without the danger of bridge loops, or the need
for manual enabling/disabling of these backup links.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Ethernet Link Speed

Link The link speed of Ethernet port can be changed manually into 10/100 Half/Full duplex.

DHCP Server Setting
The APM-100R(H) series can be configured as a DHCP server for a LAN network. Once the DHCP
Server is chose as on, the DHCP server setting elements will spread out on the page.

DHCP Server Allows you to enable or disable the DHCP server function in system.

IP Start / End The IP Start and End Address specify the range of addresses assigned by your device

when it functions as a DHCP server.

Primary & Secondary DNS Set the primary and secondary DNS server IP address which DHCP server

is going to assign for DHCP client devices.

Default Gateway Default gateways IP address assign for DHCP client devices.

Management VLAN

Management VLAN Management VLAN is a secure VLAN which divides Internet users from device IP

access. Administrators can management network devices under the Management LAN network
without betrayal of secrets.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Wireless

Wireless > Radio Setup

Wireless Band Choose a radio frequency for signal transmission. The frequency and channel

bandwidth match to selection is showed as following table:

Channel Available channel will relate to what wireless band is chosen.

Transmission Power Control the transmit power of a radio by selection of Transmission Power.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Antenna Number APM-100R(H) series complete 802.11n 1x1 1-steram and 2x2 2-stream for antenna

attached. The maximum data link rate at 1-steram and 2-stream will be 130Mbps and 300Mbps.

Short Guard Interval The guard interval is the space between symbols (characters) being transmitted.

Adding time between symbol transmissions allows these echoes and reflections to settle in before the
next symbol is transmitted. In normal 802.11 operations, the guard interval is 800 ns. A short guard
interval will short the time between symbol transmissions into 400 ns to enhance the efficiency of data
transmission.

Aggregation Frame aggregation is a feature of the 802.11n wireless LAN standards that increases

throughput by sending two or more data frames in a single transmission.

Distance To assign a distance between nodes in a point to point transmission will improve the success

rate of data transmit.

Wireless > WLAN Setup

Each physical radio interface supports up to 16 virtual WLAN AP setting. User can add or delete a
virtual AP by click the “+” or “-” button on top of the very right side of setting block.

SSID A service set identifier (SSID) is a name that identifies a particular 802.11 wireless LAN. A client

device receives beacon messages from all access points within range advertising their SSIDs. The
client device can then either manually or automatically select the network with which to associate.

Broadcast Network administrator can choose broadcast beacon messages of a virtual AP by checking

the broadcast block.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Enable Network administrator can also decide functioning of virtual AP or let it idle.

WLAN Mode Radios support “Access Point”, “Wireless Station”, “Access Point (WDS Support)” and

“Wireless Station (WDS Support)” mode to meet various network scenarios.

RTS “Request to send” is the optional mechanism used by the 802.11 wireless networking protocols

to reduce frame collisions introduced by the hidden node problem. Set the packet size to trigger
RTS/CTS enable. This is normally set in AC side only because the hidden station problem does not
exit from the perspective of the AP. RTS Threshold can be set between 1 and 2312 bytes.

Fragmentation Set the packet size to activate fragmentation. Fragmentation threshold can be set

between 1 and 2312 bytes.

Note: Fragmentation setting will be automatically disabled, once the frame aggregation is enabled.

Limited Data Rate Limit the wireless data link rate to enhance the stability of data transmission.

VLAN ID In order to create a wireless VLAN environment, each virtual AP can conform to an 802.1q

VLAN tag ID.

VLAN Priority Each VLAN ID can be gave a priority number (from 0 to 7) for data process priority.

Client Numbers Limit the maximum number of associate client devices.

Client Isolation Client isolation will protect the privacy of each connecting client from searching in a

wireless LAN.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Bandwidth Profile Choose a bandwidth control profile for virtual AP interface. (About the detail of

bandwidth profile, please refer to the bandwidth control setup in coming pages.)

Wireless > Wireless Security

SSID User can choose a specific virtual AP to assign a security type of wireless link.

MAC Filter MAC filter provides allow or deny MAC table for administrator to access control of AP by

insert a MAC address of client device. When running allow mode, only the MAC address which
showing on the table will be accept for wireless connectivity. When running deny mode, MAC address
which showing on the table will be blocked from wireless connectivity. The table can be configured 32
MAC address at most of each virtual AP interface.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Security Comprehensive security settings are available on system in this menu. These include WEP

Keys and WPA+WPA2-PSK. Details of each type of security are in appendix. The security settings are
independent between each virtual AP interface.

WEP System supports 64-bit, 128-bit and 152-bit WEP key in both ASCII and HEX format. Do make
sure the correctly number of digits/characters and format of WEP key as shown in the table are
entered. Note that in HEX format, HEX number cannot start with “0”.

Number of

digit/character

ASCII

HEX

64-bit

5

10

128-bit

13

26

152-bit

16

32

WPA+WPA2-PSK APM-100R(H) series support WPA+WPA2-PSK (WPA-Personal) in security.
WPA+WPA2-PSK (Pre-shared key) mode is designed for home and small office networks and doesn't
require an authentication server. Each wireless network device authenticates with the access point
using the same 256-bit key.

TKIP Temporal Key Integrity Protocol: A 128-bit
per-packet key is used, meaning that it dynamically generates a new key for each packet. Used by
WPA.

CCMP An AES-based encryption mechanism that is stronger than TKIP. Sometimes referred to as
AES instead of CCMP. Used by WPA2.

Both TKIP and CCMP encryption are available for WPA+WPA2-PSK. Pre-shared key of 8 to 63
characters are required. Group Rekey Interval can be set up to 65536 seconds.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Wireless > WMM Setup

Wi-Fi Multimedia (WMM) is a Wi-Fi Alliance interoperability certification, based on the IEEE 802.11e
standard. It provides basic Quality of service (QoS) features to IEEE 802.11 networks. WMM
prioritizes traffic according to four Access Categories (AC) - voice, video, best effort, and background.
It is suitable for simple applications that require QoS, such as Voice over IP (VoIP) on Wi-Fi phones
(VoWLAN).

Wireless > Bandwidth Control

Profile ID There are 20 bandwidth control profiles can be configured for administration.

Mode Downstream and upstream data rates for subscriber or the client devices connecting to AP can

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

be defined here. There are two bandwidth limit types in system. Both mode (UL+DL Limit Rate)
consolidates download and upload rate of each single client connection. UL/DL mode (UL/DL Limit
Rate) specifies download and upload rate of client connections. Once the bandwidth limit is enabled,
the limitation applies to all clients that connect to the AP.

Administration

APM-100R(H) series provide system management in menu partition: Administration, Which includes
configuration file management, password maintaining and SNMP setup.

Administration > Management

Firmware Upgrade Administrator can upload a new firmware file to device to keep system running by

the latest bug fixed version of firmware.

Configuration Management Administrator would like to save the configuration of device to local PC by

click “Backup Configuration”. Once hardware damage happened, administrator can restore a saved
configuration file to a new hardware without any reconfiguration. “Reset Default” allows administrator

to reload the system to factory default.

System Restart Click the “System Reboot” button will help to warm start the system.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Administration > Login Password

System allows administrator to change the “admin” and “user” login password in menu partition: “Login
Password”.

Administration > SNMP Setup

APM-100R(H) series support both SNMP V2 and V3. The configurable items show below:

System Location A description notes the device location.

System Contact A description notes the device maintaining information.

System Name A description notes the given name of device.

SNMP V3

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

RW User Name Read and write authority login ID.

RW User Password Read and write authority login password.

RO User Name Read only authority login ID.

RO User Password Read only authority login password.

AUTH method Choose the user authentication method.

ENC method Choose the SNMP data encryption method.

SNMP V2C

RW Community Read and write authority community stream.

RO Community Read only authority community stream.

Utility

APM-100R(H) series provide various software utilities helping administrator to do the network status
survey.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Utility > Ping

Graphical display helps administrator to get the responding time changes of target IP address. Insert
the remote host IP address, packet size and number in field than press

Ping

, system will show the

result on page. The result presenting can be adjusted by different choosing of graphic scale.

Utility > RSSI Calculator

Simple RSSI Calculator helps to estimate a possible RSSI and path loss by known device Tx power
(transmission power), cable loss, antenna gain and frequency both transmitting and receiving side.
Graphic displaying shows changes of path loss and RSSI.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Utility > Fresnel Zone

The First Fresnel Zone Calculator is a tool that helps you to estimate the possible obstruction from
existing object between two devices before the wireless installation. An

antenna angle

calculation can

also help you to aligning the vertical angle of the directional antenna.

Utility > Antenna Alignment Tool

In order to lift efficiency of antenna aligning, AMP-100R(H) series provide a software alignment tool
helping the installers to align and check the antenna directions.
Antenna Alignment Tool will require triggering the function both access point and wireless station (AP
Client) side. It means that both access point and wireless station (AP Client) side should be the
APM-100R(H) series product, otherwise, the function doesn’t get properly use.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Choose the SSID which you are going to do the antenna aligning and click the

Star

button both access
point and wireless station (AP Client) side to start the antenna alignment. You will able to see the
RSSI changes in figure. Try to adjust the directional antenna’s horizontal and vertical angle to get the
best RSSI level.

Link Test
A

Link Test

is additional tool base on Antenna Alignment Tool active status. When you start the

Antenna Alignment Tool, you may set a target throughput to active the

Link Test

to estimate the
packet error rate.
Choose a target throughput and test duration than click Start Test button. System will generate a test
data transmission to calculate the packet error rate.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

An

Rx rate

shows the best data rate you can reach under the current RSSI level.

Link Test Tool can also help you to do the fine tuning of your antenna direction.

Utility > Site Survey

In wireless site survey, system provides a signal scan function to detect any available wireless signal
around the AP. It will help AP installer to clarify the environment. Choose a radio interface which you
are going to do the survey on device and click

Scan

button. After few seconds, system will show the

APs around the device.

Status

Status > System Information

System Information summarizes all the configuration and hardware information of the device.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Status > System Status

Real-time link statuses of all interfaces are shown in the menu.

System Up Time Display how long APM-100R(H) has been operating since last boot-up.

Interface Status Indicate the interface is ENABLE or DISABLE.

Link Rate Data Link Rate here indicates the maximum transmission rate available, and can be used as

an indication of link quality.

Link Quality A Calculation of RSSI, signal and noise level to indicate the quality of the communication

link in percentage.

Channel The channel used by the wireless interface.

Signal Level A -70 ~ -50dBm signal level is recommended for a good connection. Too low a signal, the

wireless link between AP and AC cannot be established. Too high a signal level, the power amplifier at
the receiver might be forced to operate in saturation region and distorts the signal waveform.

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

In order to help user’s reading of the changes, system also provide a graphic interface to trace the

items’ changes. Click the

Graphic Display

button on the top left of the page, graphic mode will show on

your browser.

Status > Connecting Nodes Information

All the connecting clients’ MAC address will be display in Connecting Nodes Information, including

signal and data rate. The result shows information only when WLAN was configured as Access Point
mode.

Graphic display is also available for observing the changes.

Status > Connecting AP Information

In the “Connecting AP Information” page, RSSI, Rx rate, Tx rate and etc. are provided for verification

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

of wireless link status.

Graphic display is also available for observing the changes.

Appendix 1: Specifications

Hardware Specification

Key Components

Main Processor

Atheros AR7161(680Mhz)

Wireless Chipset

Atheros AR9220 based miniPCI module, Up to three modules

Switch Controller

Atheros AR8035 / Atheros AR8021

Flash Memory

16MBytes

SDRAM

64MBytes(Up to 128MBytes)

Console

UART x 1(PCBA onboard)

Interfaces

Wireless
Up to three 2x2 MIMO radios, mini-PCI version 1.0 type 3A

Frequency ranges :

a. USA : 2.400 ~ 2.483 GHz, 5.15 ~ 5.35 GHz, 5.5 ~ 5.7 GHz, 5.725 ~

5.825 GHz

b. Europe: 2.400 ~ 2.483 GHz, 5.15 ~ 5.35 GHz, 5.47 ~ 5.725 GHz
c. Japan: 2.400 ~ 2.497 GHz, 5.15 ~ 5.35 GHz, 5.47 ~ 5.725 GHz
d. China: 2.400 ~ 2.483 GHz, 5.725 ~5.85 GHz

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

RF ourput power of DNMA-92 :

a. IEEE802.11a

1. 21dBm@6M(all)

2. 17dBm@54M(5180MHz) 16dBm@54M(5825MHz)

b. IEEE802.11b

1. 20dBm@1M(2412MHz) 19dBm@1M(2484MHz)

2. 21dBm@11M(all)

c. IEEE802.11g

1. 23dBm@6M(all)

2. 19dBm@54M(all)

d. IEEE802.11a/n HT20

1. 21dBm@MCS0/8(5180MHz) 19dBm@MCS0/8(5825MHz)

2. 16dBm@MCS7/15(5180MHz) 14dBm@MCS7/15(5825MHz)

e. IEEE802.11a/n HT40

1. 19dBm@MCS0/8(5190MHz) 18dBm@MCS0/8(5795MHz)

2. 13dBm@MCS7/15(all)

f. IEEE802.11g/n HT20

1. 21dBm@MCS0/8(all)

2. 17dBm@MCS7/15(all)

g. IEEE802.11g/n HT40

1. 21dBm@MCS0/8(2422MHz) 20dBm@MCS0/8(2462MHz)

2. 16dBm@MCS7/15(all)

Receive Sensitivity of DNMA-92 :

a. IEEE802.11a

1. -82dBm@6M, 1Rx -95/-91dBm@6M, 2Rx

2. -65dBm@54M, 1Rx -79/-75dBm@54M, 2Rx

b. IEEE802.11b

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

1. -82dBm@1M, 1Rx -95/-91dBm@1M, 2Rx

2. -76dBm@11M, 1Rx -91/-87dBm@11M, 2Rx

c. IEEE802.11g

1. -82dBm@6M, 1Rx -95/-91dBm@6M, 2Rx

2. -65dBm@54M, 1Rx -80/-76dBm@54M, 2Rx

d. IEEE802.11a/n HT20

1. -82dBm@MCS0, 1Rx -95/-91dBm@MCS0, 2Rx

2. -64dBm@MCS7, 1Rx -77/-73dBm@MCS7, 2Rx

e. IEEE802.11a/n HT40

1. -79dBm@MCS0, 1Rx -91/-87dBm@MCS0, 2Rx

2. -61dBm@MCS7, 1Rx -74/-70dBm@MCS7, 2Rx

f. IEEE802.11g/n HT20

1. -82dBm@MCS0, 1Rx -95/-91dBm@MCS0, 2Rx

2. -64dBm@MCS7, 1Rx -77/-73dBm@MCS7, 2Rx

g. IEEE802.11g/n HT40

1. -79dBm@MCS0, 1Rx -90/-86dBm@MCS0, 2Rx

2. -61dBm@MCS7, 1Rx -74/-71dBm@MCS7, 2Rx

RF output power of DNMA-H92 :

a. IEEE802.11a

1. 24dBm@6M(all)

2. 21dBm@54M(all)

b. IEEE802.11b

1. 24dBm@1M(all)

2. 24dBm@11M(all)

c. IEEE802.11g

1. 25dBm@6M(all)

2. 22dBm@54M(all)

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

d. IEEE802.11a/n HT20

1. 24dBm@MCS0/8(all)

2. 18dBm@MCS7/15(5180MHz) 17dBm@MCS7/15(5825MHz)

e. IEEE802.11a/n HT40

1. 22dBm@MCS0/8(all)

2. 17dBm@MCS7/15(5190MHz) 16dBm@MCS7/15(5795MHz)

f. IEEE802.11g/n HT20

1. 25dBm@MCS0/8(all)

2. 21dBm@MCS7/15(all)

g. IEEE802.11g/n HT40

1. 24dBm@MCS0/8(all)

2. 20dBm@MCS7/15(all)

Receive Sensitivity of DNMA-H92 :

a. IEEE802.11a

1. -82dBm@6M, 1Rx -95/-91dBm@6M, 2Rx

2. -65dBm@54M, 1Rx -79/-75dBm@54M, 2Rx

b. IEEE802.11b

1. -82dBm@1M, 1Rx -92/-88dBm@1M, 2Rx

2. -76dBm@11M, 1Rx -92/-88dBm@11M, 2Rx

c. IEEE802.11g

1. -82dBm@6M, 1Rx -95/-91dBm@6M, 2Rx

2. -65dBm@54M, 1Rx -80/-76dBm@54M, 2Rx

d. IEEE802.11a/n HT20

1. -82dBm@MCS0, 1Rx -95/-91dBm@MCS0, 2Rx

2. -64dBm@MCS7, 1Rx -77/-73dBm@MCS7, 2Rx

e. IEEE802.11a/n HT40

1. -79dBm@MCS0, 1Rx -91/-87dBm@MCS0, 2Rx

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

2. -61dBm@MCS7, 1Rx -73/-69dBm@MCS7, 2Rx

f. IEEE802.11g/n HT20

1. -82dBm@MCS0, 1Rx -95/-91dBm@MCS0, 2Rx

2. -64dBm@MCS7, 1Rx -77/-73dBm@MCS7, 2Rx

g. IEEE802.11g/n HT40

1. -79dBm@MCS0, 1Rx -92/-88dBm@MCS0, 2Rx

2. -61dBm@MCS7, 1Rx -74/-70dBm@MCS7, 2Rx

Ethernet
10/100/1000 Base-TX MDI/MDIX RJ-45 x 1

Compliant with :

a. IEEE802.3 / 802.3u / 802.3at

Hardware based 10/100/1000, full/half, flow control auto negotiation

Connector

2 x N-type(1 radio)
4 x N-type(2 radios)
6 x N-type(3 radios)

Power Requirement

48V 1A PoE Support Gigabit Ethernet Link

Watch Dog

Hardware Watch Dog

Physical

Dimensions

220 x 220 x 77 mm

Weight

101R/101RH—1.8Kg 102R/102RH—1.9Kg 103R/103RH—2.0Kg

2.0kg (3.7kg mount kit included)

Environmental

Temperature Range

-20℃~70℃

Humidity

0% ~ 95% Non-condensing

Storage

-40~ 85℃

Dusty & Waterproof

Outdoor IP67 rated

Regulatory

Certification

FCC, CE Processing (will announce in 2011/12)

Safety

Processing

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Software Specification

System Operation

Bridge Mode

Layer 2 Switching Learning Technology

Store-and-Forward

Spanning Tree Protocol - IEEE 802.1d STP / IEEE 802.1w RSTP / IEEE

802.1s MSTP

Static IP / Dynamic IP

DHCP server / client

Multicast / Broadcast Storm Limitation

IEEE 802.1q Tag VLAN

IEEE 802.1p VLAN Priority Based QoS

Network Interface

Wireless

IEEE 802.11 a/b/g/n 2.4GHz / 5GHz Dual Band Radio

2 x 2 MIMO Technology

Single Radio / Dual Radios / Triple Radios

AP mode / Client mode / WDS mode

IEEE 802.11h DFS

WMM QoS

Channel / Tx Power / Data Rate / Max Distance Adjustable

Advanced Wireless Parameters Adjustable

Multi-SSIDs / VLAN tags mapping(Up to 16 x ESSIDs for each radio)

Wireless Site Survey

Node Information

Concurrent Connected Node Limitation

Client User Isolation

Wire

48V 1A PoE Support Gigabit Ethernet Speed

Ethernet Link Speed Configurable

10/100/1000 Base-TX MDI/MDIX RJ-45

Performance

Wireless

To

TCP
Up to 180Mbps for one radio to Ethernet

Up to 320Mbps for two radios to Ethernet

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Wire

Up to 320Mbps for three radios to Ethernet

UDP

Up to 240Mbps for one radio to Ethernet

Up to 350Mbps for two radios to Ethernet

Up to 350Mbps for three radios to Ethernet

PPS

>= 20,000@short packet for one radio to Ethernet

>= 28,000@short packet for two radios to Ethernet

>= 28,000@short packet for three radios to Ethernet

Latency

< 5ms

Multiple
Hops

2 hops

Up to 160Mbps

3 hops

Up to 150Mbps

>= 4hops

Up to 140Mbps

PPS

>= 20,000@short packet at multiple hops

Latency

< 10ms

Management

HTTP(s) WEB GUI

Telnet

SSH

Console(optional interface)

CLI commands

SNMP v2c/v3, standard / private MIBs

Syslog

Security

Hide SSID(turn off ESSID broadcasting)

MAC Address ACL

WEP 64/128/152 bits

IEEE 802.1x EAP-MD5 / EAP-TLS / EAP-TTLS

WPA / WPA2 PSK / EAP with TKIP / CCMP AES based Encryption

IO-Power Technology Co., Ltd 1F,No.100, Jinzhu Rd., North Dist., Hsinchu City 30053, Taiwan

http://www.io-power.com e-mail: [e-mail] Tel: [phone] Cell: 0933168849 Fax: [phone]

Form No.：IOP-OANI-001-001 Rev.：A.1 保存期限：6 年

Management VLAN Tag

NTP Client

Firmware upgrade / downgrade

Dual Images

Dual Configuration files / Factory Default

Multiple Level Management

Advanced Technology

Multiple Hopping

Up to 10 hops with more than 120Mbps throughput

Configurable Max. Hop Counts(default 20 hops)

Advanced Features

Wireless Bandwidth Limitation