Page 1
Ion Technologies Sumpro
Battery Back-Up
®
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
Page 1 of 12
2. Risk of electrical shock. Connect only to a
properly grounded, three pronged grounding
type receptacle. Under any circumstances,
do not remove the grounding prong from the
power cord.
3. Do not smoke, use sparkable electrical devices
or open ame when working on this unit!
4. Do not install Unit in locations classied as
hazardous per N.E.C., ANSI/NFPA 70 - 2014.
FAILURE TO HEED ABOVE CAUTIONS
COULD RESULT IN INJURY OR DEATH.
The Sumpro® is designed to operate a load up to
12 Amps. If operating more than one pump, the
combined FLA cannot exceed 12 Amps.
Important Safety Instructions
Introduction
Reasonable care and safe methods should be
practiced. Check local codes and requirements
before installation. This manual contains important
information for the safe use of this product. Read
this manual completely before using this product and
refer to it often for continued safe product use.
Note: This manual covers the installation of the
inverter, regardless of what pump, switch or
controller combination is included in the system you
purchased. For more detailed installation information
and troubleshooting regarding the pump, switch or
controller, please refer to their individual manuals.
DO NOT THROW AWAY OR LOSE THIS MANUAL.
Keep it in a safe place so that you may refer to it when
needed.
Warning
WARNING: Always disconnect the Unit from
the receptacle power source and battery
before handling or making any adjustments to the
system.
Battery Backup Warning:
1. Risk of electrical shock this Unit has not been
investigated for use in outdoor areas.
Before proceeding further, please review the safety
instructions carefully.
General Precautions:
• Before using the inverter read all instructions
and caution markings on the inverter, the
batteries & all appropriate sections of this
instruction manual.
• Do not expose the inverter to any type of
chemicals. The inverter is designed for interior
use only.
• Do not disassemble the inverter; contact
Metropolitan Industries Wholesale Customer
Support at (800) 323-1665 when service or
repair is required. Opening by unqualied
personnel can lead to electrical shock or re
hazard and void the warranty.
• To reduce risk of electric shock, disconnect all
wiring before cleaning.
WARNING: Avoid exposing the inverter or
batteries to any type of explosive gases, as
batteries generate explosive gases during normal
operation. Install the batteries in a well ventilated
area.
To reduce the risk of battery explosion, follow all the
instructions of the battery supplier or any equipment
you intend to use in the vicinity of batteries.
www.ionproducts.net
Page 2
Ion Technologies Sumpro
Battery Back-Up
®
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
Page 2 of 12
• Use the correct insulated tools to make AC/DC
wiring connections.
• Do not install this inverter on or near ammable
materials (plywood, chemicals, gas line etc.)
CAUTION:
Personal Precautions:
• Someone should be within the range of your
voice to come to your aid when you work near
batteries.
• Have plenty of fresh water and soap nearby
in the event that battery acid contacts skin,
clothing or eyes.
• Wear complete eye, skin and clothing
protection.
• Avoid touching eyes while working near
batteries. Wash your hands when done.
• If battery acid comes in contact with skin or
clothing, wash immediately with soap and
water.
Knowing Your Inverter
CAUTION: The electrolyte is a dilute sulfuric
acid that is harmful to the skin and eyes. It is
electrically conductive and corrosive. The following
procedures should be observed:
a. If electrolyte contacts the skin, wash it o
immediately.
b. If electrolyte contacts the eyes, ush
thoroughly and immediately with water.
Seek medical attention.
c. Spilled electrolyte should be washed down
with a suitable acid neutralizing agent. A
common practice is to use a solution of
approximately one pound (500 grams)
bicarbonate of soda to approximately one
gallon (4 liters) of water. The bicarbonate
of soda solution should be added until the
evidence of reaction (foaming) has ceased.
The resulting liquid should be ushed with
water and the area dried.
CAUTION: Do not reverse the battery
connections, as it will blow the battery fuse. A
power cord has been provided to connect the inverter
to incoming AC wall outlet.
In its most basic form, an Inverter transforms Direct
Current (DC) to Alternating Current (AC). The battery
pack acts as reserve power to ensure continuous
supply of power whenever electrical supply from utility
power is not available. The inverter is used to charge
the batteries when normal utility power is available
and converts the battery’s DC to AC voltage to run the
pump when utility power is lost.
Battery Safety
CAUTION: Do not dispose of batteries in a
re. The battery may explode.
CAUTION: A battery can present a risk of
severe burn and injury from high short circuit
current. The following precautions should be observed
when working on batteries.
CAUTION: Do not open or mutilate the
battery. Released electrolyte is harmful to the
skin and eyes. It may be toxic.
Battery Requirements
Your Unit operates on 24 volt DC battery power
when in the power fail mode. Two UL recognized
deep cycle marine batteries should be used. There
are two principal types of batteries: starting and deep
cycle. There are several dierent types of battery
constitutions including liquid lead acid, nickel iron,
nickel cadmium, alkaline and maintenance free.
Batteries are sealed or vented.
NOTE: All batteries must be the same make, model,
and age for the inverter to function properly.
Starting Batteries (NOT RECOMMENDED)
Starting batteries are designed for high cranking
power but not deep cycling. DO NOT use them with
your inverter. They do not aect the inverter, but they
will simply not last long in a deep cycle application.
They use a lot of thin plates to maximize the surface
area of the battery. This allows very high starting
current but less run time when the battery is cycled.
www.ionproducts.net
Page 3
Ion Technologies Sumpro
Battery Back-Up
®
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
Page 3 of 12
Deep Cycle Batteries (RECOMMENDED)
Deep Cycle batteries, also known as marine batteries,
are best suited for use with the inverter. They are
designed to have the majority of their capacity used
before recharge. Available in many sizes and types,
be sure to use at least a 100 AH battery.
BATTERIES NOT INCLUDED
Tools Needed
An insulated adjustable wrench will be needed.
Installation
The Sumpro® unit is packaged in two separate cartons
containing one complete unit and a fuse link. Below
are the contents.
Fuse Link
PN: A0000702i7
reach of the power cord. When fully assembled, the
head unit with batteries weighs appoximately 200
lbs. It is recommended to use the optional Sumpro®
stand to keep the unit o the oor. A dedicated 15A
receptacle circuit is recommended.
3. Assembly
Set the battery box in place, making sure that the
openings will be facing the back of the head unit. Once
in place, place the head unit in front of the battery box
feeding the battery leads through the large holes in
the front of the battery box.
4. Battery Installation
Now that the unit has been properly assembled and in
its permanent location the batteries can be installed.
Note: If the battery post conguration diers from that
shown on Page 4, Figure A, additional post adapters
may be required.
CAUTION: Important Safety Instructions
A battery can present a risk of electrical
shock and high short circuit current. The following
precautions should be observed when working on
batteries.
Sumpro® Head Unit
PN: iS20281
®
Sumpro
See accompanying unit assembly drawings.
1. Unpack The Sumpro
Your Sumpro® auxiliary power supply should be in
two separate containers. Remove the contents from
the containers. They should include the head unit,
the battery box and the fuse link (located inside the
battery box).
Open the lid on the battery enclosure and remove the
fuse link from inside.
2. Location
Find a suitable place to set the unit (when it is
assembled). Keep in mind that the unit should be
placed in an area where water and moisture will not
splash or drip on the unit, the fan inlet on the front
of the head unit will not be obstructed, and where a
properly grounded three prong receptacle is within
Battery Box
PN: iB20386
®
1. Remove watches, rings, or other metal objects.
2. Use tools with insulated handles.
3. Do not lay tools or metal objects on top of
batteries.
4. Wear safety goggles and a face shield.
After taking the above precautions, secure the battery
box to the head unit using the screws provided.
Lower the two 12V batteries into the battery box with
the terminals facing each other. At this time check
the polarity of your batteries. Facing the front of the
Sumpro® unit, the left battery terminal should be
positive, and the right negative (See Page 4, Figure
A). If this is not the case, DO NOT continue until the
proper batteries can be obtained.
5. CONNECTING BATTERIES
Now that the batteries have been installed, and the
polarity conforms to the Sumpro®, connect the fuse
link across the back battery terminals (See Page
4, Detail A). Remove the protective cover from the
negative (-) battery lead (black) then connect it to
the negative (-) post of the battery. Screw down bolt
tightly.
www.ionproducts.net
Page 4
Figure A
Ion Technologies Sumpro
Battery Back-Up
BATTERY BOX
MOUNTING SCREWS
®
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
Page 4 of 12
ALTERNATIVE DC
INPUT ACCESS COVER
POSITIVE BATTERY
LEAD AND TERMINAL
FUSE LINK
NEGATIVE BATTERY
LEAD AND TERMINAL
Detail A
POSITIVE TERMINAL
A
NEGATIVE TERMINAL
www.ionproducts.net
Page 5
Ion Technologies Sumpro
Battery Back-Up
Figure B
®
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
Page 5 of 12
BATTERY BOX LID SCREW
ONE THIS SIDE AND ONE OPPOSITE SIDE
Figure C
DC1 TERMINALS DC2 TERMINALS 6P6C/RJ11 JACK
REMOVE KNOCKOUT
INSTALL FLEXIBLE
METAL CONDUIT
Plug the Sumpro® unit into the designated 115V AC
outlet.
6. Within 30 seconds, remove the protective cover
from the positive (+) red battery lead then connect it
to the positive (+) post.
Note: Make sure all battery connections are properly
tightened to 75 pound inches.
7. Close Unit
instructions in the controller manual. The controller
will be plugged into the Sumpro® instead of the wall
outlet.
If connecting a home alarm system to the Sumpro®,
make the connection to the 6P6C/RJ11 jack labeled
“ALARM CONTACT”. The center most pins (#3 and
4) are used for this circuit, and are normally closed
(N/C) under normal conditions. These pins electrically
open in a Sumpro® alarm condition.
Close and secure the battery enclosure lid using the
screws provided, so that children cannot tamper with
the unit (See Page 5, Figure B).
8. Plug In The Pump
At this time you may plug your 115V pump into your
Sumpro® unit, not exceeding the load limit of 12 amps
or 1440 watts at any one time.
Note: If connecting a pump controller, such as the
Ion Genesis or Ion Endeavor, follow the installation
www.ionproducts.net
Alternative DC Input Connections
The alternative DC inputs provide an alternate means
of charging the batteries via power source(s), not
included. When an alternative DC source is connected
to the Sumpro, it will charge the batteries if the
generated power is greater than the battery voltage,
whether or not AC power is available. If two alternative
DC power sources are connected at the same time, the
Sumpro utilizes the one generating the most power.
Page 6
Ion Technologies Sumpro
Battery Back-Up
®
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
Page 6 of 12
Please read the following instructions carefully before
attempting to connect an alternative DC source.
1. There are two sets of alternative DC input
terminals located on the top left side of
the Sumpro, DC1 and DC2. Open access
cover and remove the conduit knockout that
corresponds to the terminals you are going to
connect to (See Page 5, Figure C).
2. Connect conduit to the head unit (See Page
5, Figure C). Check local codes for conduit
requirements.
3. Run the wires from the alternative DC source
and connect the positive (+) wire to the positive
(+) DC terminal and the negative (-) wire to the
negative (-) DC terminal.
NOTE: It doesn’t matter which DC input is utilized, but
insure that the positive (+) and negative (-) wires from
the alternative DC source are connected to the same
set of DC terminals, i.e., if using DC2 terminals, the
positive and negative wires from the alternative DC
source must be connected to the positive and negative
terminals of DC2.
4. Put access cover back on the head unit.
a. Blinks when alarm condition occurs and
silence has NOT been pressed
b. Solid when alarm condition occurs and
silence has been pressed
c. O when no alarm condition is present
d. Alarm Contact – NC dry contact
i. Opens when either the Inverter LED or
Alarm LED are blinking
4. LCD Display - Displays all info that pertains to
current operating condition of the unit
Testing the System
To test the Sumpro®, simply unplug it from the 115V
AC power to run your pump on battery power for a
short time. You can repeat this if you wish, but it is
not necessary. If your Sumpro
time it is sure to work time and time again. Be sure
that you remember to plug the unit back into the
receptacle after you have completed the test.
Note: New batteries are rarely fully charged.
Depending on the charge condition of the batteries
and the voltage from the utility company, it may take
up to 7 days for the batteries to be fully charged.
®
unit works the rst
Light and Relay Functions
After you have your Sumpro® unit in operation, you can
check its status by looking at the system lights. They
should tell you everything you need to know about the
status of the unit.
1. Power – Green LED
a. Solid when AC Line In Voltage is deemed
present.
b. O when AC Line In fault occurs.
2. Inverter – Red LED
a. Blinks when unit is running o inverter and
silence has NOT been pressed.
b. Solid when unit is running o inverter and
silence has been pressed.
c. O when unit is operating o of AC Line
3. Alarm – Red LED
Sumpro® Maintenance
Your Sumpro® unit has been designed to be virtually
maintenance free. Just make sure it is kept clean and
dry and that the unit is periodically tested in the auxiliary
mode.
Battery Maintenance
If you are using AGM maintenance free batteries, you
should visually inspect the batteries every six months
for swelling or leakage. For all other batteries, refer to
the manufacturer recommended battery maintenance
section of the battery being used.
Maintenance or replacement of batteries should be
performed or supervised by personnel knowledgeable
of batteries and the required precautions.
www.ionproducts.net
Page 7
Ion Technologies Sumpro
Battery Back-Up
®
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
Page 7 of 12
Replacing Batteries
Wear full eye protection and protective clothing.
When replacing the batteries, use the same type and
size batteries. See battery requirements (Page 2).
CAUTION: The electrolyte is a dilute sulfuric
acid that is harmful to the skin and eyes. It is
electrically conductive and corrosive. The following
procedures should be observed:
• Do not lay tools or metal objects on top of the
batteries
• Use tools with insulated handles
1. Unplug the unit from the wall.
2. Follow the Installation Instructions found on
page 3 of this manual, starting with step 8 and
working back to step 1.
3. Remove and safely dispose of old batteries.
4. Install new batteries per the installation
instructions on page 3.
100
90
80
70
60
50
40
30
20
10
Duty Cycle (% of time running)
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 20 25 30
Reserve Power (total hours of operation)
Performance curve results using a 3/4 HP pump with
a 7.5 FLA and (2) Metropolitan Power Plus model
31P-36 batteries.
Warranty Is Void If...
1. Power cord has been cut or the grounding
prong has been removed.
2. Unit has been used in an outdoor application.
3. Batteries not meeting the above specications
have been used.
4. Unit has been submerged in water.
Technical Specifications
Model 100
A.C. Lower Voltage Limit 98 VAC ± 5V
Output Voltage with Full Load 85-135V ± 10V
Maximum Output Current 12 FLA
Battery Lower Voltage Limit 18.5V ± 0.3V
Main Output Frequency 60 Hz
Overload 125 ± 3% (With Auto
Reset Function)
Alarm Contact RJ11 Connection,
Normally Closed Dry
Contact
Alternative DC Inputs 24VDC, 20A max
5. Unit has been tampered with in any manner
not described in the above instructions.
6. Unit has been disassembled by the customer.
7. Unit has been applied to products exceeding
the maximum capacity of the Unit, i.e., a pump
other than the one supplied with the unit or
more than one pump.
8. Unit has been applied to the wrong voltage.
9. Any labels or cord tags have been removed.
www.ionproducts.net
Page 8
Ion Technologies Sumpro
Battery Back-Up
®
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
Page 8 of 12
Troubleshooting
Please read the following before calling in for technical
support as these are the most common, and easiest
to rectify, issues that may occur with your Sumpro®
unit.
System says that the batteries are too low
1. Check the age of the batteries.
a. We recommend that batteries be
replaced every 3 years to insure optimum
performance
b. Batteries must be the same age, make and
model in order for the Sumpro® to function
properly.
2. If using a wet battery, check water levels.
Normal Operation LCD Displays
LCD Display Description Remedy
1
Sumpro Status
The unit is operating o of AC Line
power and is functioning normally.
NORMAL
3. Clean all battery connections and leads with a
wire brush or sand paper. Even new batteries
could have a slight coating on the connections
that could cause issues. Ensure that battery
terminal screws are tightened to 75 pound
inches.
4. Check fuse link for blown fuses.
The system is stuck in a fault that won’t clear
1. Reboot the system
a. While in AC mode, disconnect the positive
(+) red wire from the battery terminal
b. Unplug the Sumpro® from the wall outlet
c. Wait a few minutes and plug the Sumpro®
back into the wall outlet
d. Within 30 seconds, reconnect the positive
(+) red wire to the battery terminal
Normal
2
Sumpro Status
The unit is in DC mode and running
o of power provided by attached
batteries.
Normal
BATTERY BACKUP
3
The unit is charging the batteries. Normal
Sumpro Status
BATTERY CHARGING
4
Input Voltage
The input voltage when running o
of AC power from the utility.
Normal
120V
5
Battery Current
Current going to the batteries
during charging.
Normal
15.0 A
6
Output Current
Current going to the connected load
while in DC mode.
Normal
5.0 A
www.ionproducts.net
Page 9
Ion Technologies Sumpro
Battery Back-Up
LCD Display Description Remedy
7
Battery Voltage
26.7 V
®
Battery voltage when batteries are
deemed present.
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
Page 9 of 12
Normal
8
Battery Capacity
91%
Battery capacity when batteries
are deemed present. Capacity is
calculated based on battery voltage
alone. While inverting, the battery
capacity can drop 15-20% when
load is connected and running.
Normal
Alarm & Fault Code LCD Displays
Below are the most common alarms and faults. For a complete list of LCD display alarms and faults, please refer
to the separate Sumpro
1
Batteries Not
2
AC Input Voltage
®
Troubleshooting Guide on our web site.
LCD Display Description Remedy
Installed
LOST
The unit will detect that batteries are
connected by installing fully charged
batteries or if it draws sucient
current while charging.
The unit has detected a loss of
AC power from the utility and has
switched to DC mode.
Install batteries of the
same age, make and
model. Once the unit
detects that batteries
are present, the unit will
always assume batteries
are connected unless
the unit is completely
powered o.
The unit must detect
good AC voltage before
switching back to AC
mode.
3
AC Input Voltage
UNDERVOLTAGE
4
AC Input Voltage
OVERVOLTAGE
5
Invert Lock OFF:
10 S
6
Charge Lock OFF:
10 S
www.ionproducts.net
The unit has detected an
undervoltage condition and has
switched to DC mode.
The unit has detected an overvoltage
condition and has switched to DC
mode.
The unit has suspended DC mode
because of a fault condition. The
display shows time left before DC
mode will resume.
The unit has suspended battery
charging because of a fault condition.
The display shows time left before
charging start timer can begin.
The unit must detect
good AC voltage before
switching back to AC
mode.
The unit must detect
good AC voltage before
switching back to AC
mode.
DC mode will resume
after the time expires.
Battery charging will
resume after the timer
expires.
Page 10
Ion Technologies Sumpro
Battery Back-Up
LCD Display Description Remedy
7
Cool Lock OFF:
10 S
8
Fault Lock OFF:
10 S
9
Sumpro Status
INVERT SUSPENDED
®
The unit has suspended battery
charging because it needs to cool
o for a period of time. The display
shows time left before charging start
timer can begin.
The unit has entered into a fault
condition and has suspended all
operations. The display shows time
left before operations can begin
again.
The unit has stopped DC mode due
to a fault condition. Subsequent
screens will state info regarding
suspension.
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
Page 10 of 12
Battery charging will
resume after the timer
expires.
Normal operation will
resume after the timer
expires.
The underlying fault
condition must clear and
the related lock timer must
elapse.
10
Sumpro Status
FAULTED
The unit has detected a fault
condition and has stopped all
operations until condition clears
and/or necessary time has elapsed
since fault.
The underlying fault
condition must clear and
the related lock timer must
elapse.
www.ionproducts.net
Page 11
Ion Technologies Sumpro
Battery Back-Up
®
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
Page 11 of 12
Warranty Registration Card
Please ll out and send back to: Metropolitan Ind. Warranty Department P.O. Box 7266 Romeoville, IL 60446. Or
to register online, go to www.ionproducts.net
Sumpro® Warranty Registration Card
To register your purchase, please ll in the following information:
Name:
Address:
City
Purchased From:
Serial Number*:
Installed By:
* The serial number is located next to the auxiliary inputs.
Date:
State: Zip:
Phone:
www.ionproducts.net
Page 12
Ion Technologies Sumpro
Battery Back-Up
1. Coverage and Term. Metropolitan Industries, Inc. (“Metropolitan”) warrants to the original
purchaser (the “Buyer”) of each Ion® product (the “product”), that any part thereof which proves to be
defective in material or workmanship within three (3) years from date of manufacture, will be replaced at no
charge with a new or remanufactured part, F.O.B. factory. Buyer shall be responsible for all freight charges
and all costs of fi eld labor or other charges incurred in the removal and/or reinstallation of any product, part
or component thereof.
2. Exclusions. THE WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONS AND
EXCLUSIONS:
(a) The Warranty excludes products or workmanship which becomes defective as a result
of: (i) earthquake, fi re, storms, the elements or any other acts of God; (ii) normal wear and tear from use;
(iii) accident, misuse, abuse or neglect; (iv) modifi cations made by Buyer or any third party, other than
Metropolitan; and (v) Buyer’s failure to properly install, maintain, service and/or operate the product under
normal conditions and according to manufacturer’s instructions.
(b) Metropolitan shall not be responsible for, and the Warranty shall not cover, extended
damage which occurs because of Buyer’s failure to notify Metropolitan promptly in writing of apparent
defects.
(c) Any part or component designated as manufactured by anyone other than Metropolitan
shall be covered only by the express warranty of the manufacturer thereof.
(d) The Warranty shall lapse upon Buyer’s failure to fully comply with the terms and conditions
of its contract with Metropolitan, including Buyer’s failure to pay the purchase price for the product or any
portion thereof. Buyer’s subsequent compliance with the terms and conditions of any such contract, will not
cause the term of the Warranty to extend beyond the time period set forth above.
(e) No actions taken by Metropolitan to correct a defect in a product shall extend the Warranty
beyond the period set forth above. Metropolitan shall not be obligated to remedy any defect, where otherwise
required pursuant to the Warranty unless and until Buyer notifi es Metropolitan in writing of the defect and
then only if such notifi cation is made prior to the expiration of the period set forth above.
3. Process of Claims and Repairs. Metropolitan agrees that if the product or any part or component
thereof shall fail to conform to the terms of this Warranty, Metropolitan shall replace such nonconforming
product, part or component at the original point of delivery and furnish instruction for its disposition. Any
transportation charges involved in such disposition and all costs of fi eld labor or other charges incurred in the
removal and/or reinstallation of any product, part or component thereof shall be the responsibility of Buyer.
4. Limitation on Liability. Notwithstanding any provision to the contrary, Metropolitan’s entire
liability under this Warranty shall not in the aggregate exceed, and Buyer’s exclusive and sole remedies
are, to the extent permitted by law, shall be to secure replacement of the defective product. UNDER NO
CIRCUMSTANCES SHALL METROPOLITAN BE LIABLE UNDER THE WARRANTY FOR
ANY INDIRECT, PUNITIVE, SPECIAL, EXEMPLARY, CONSEQUENTIAL OR INCIDENTAL
DAMAGES (INCLUDING LOST PROFITS, REVENUE, USE OR ECONOMIC ADVANTAGE).
5. Express Waiver of Any Other Warranties. THE EXPRESS WARRANTY SET FORTH IN THIS
WRITTEN W ARRANTY IS THE ONL Y W ARRANTY MADE BY METROPOLIT AN, OR ANY OTHER
PARTY, IN CONNECTION WITH ANY PRODUCT PURCHASED FROM METROPOLITAN.
NEITHER METROPOLITAN, NOR ANY OTHER PARTY, MAKES ANY OTHER EXPRESS OR
IMPLIED WARRANTY WHICH IS NOT SET FORTH HEREIN, AND METROPOLITAN HEREBY
DISCLAIMS AND BUYER HEREBY WAIVES ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTY OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE.
6. Not Transferable. The Warranty may not be transferred and shall be void on the sale or other transfer
of the product.
7. Products and Warranty Subject to Change. Metropolitan reserves the right to make revisions to its
products and their specifi cations, and to revise this Warranty and related information without notice.
®
OPERATION MANUAL
Dated: 08/18/2017
Document Name: SUMPRO_100_OM
3 Year Residential W arranty
Page 12 of 12
www.ionproducts.net
Loading...