ION Audio Tailgater User Manual [fr]

TAILGATER

PORTABLE
SOUND SYSTEM
FOR iPod

ENGLISH ( 1 – 2 )

 MANUAL DE INICIO RÁPIDO

ESPAÑOL ( 3 – 4 )

 GUIDE D'UTILISATION SIMPLIFIÉ

FRANÇAIS ( 5 – 6 )

 GUIDA RAPIDA

ITALIANO ( 7 – 8 )

 KURZANLEITUNG

DEUTSCH ( 9 – 10 )

NEDERLANDS ( 11 – 12 )

 QUICKSTART GUIDE

 SNELSTARTGIDS

QUICKSTART GUIDE (ENGLISH)

1. Make sure all items listed on the front of this guide are included

in the box.

2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING

THE PRODUCT.

3. MAKE SURE THAT YOU HAVE COMPLETELY CHARGED

THE BATTERY PRIOR TO FIRST USE FOR MAXIMUM
BATTERY LIFE.

4. Study this setup diagram.

5. Place product in an appropriate position for operation.

6. Make sure all input devices such as microphones, CD players, MP3 players, and linked amplifiers/PAs are

turned off and volume settings are set at “zero.”

7. Connect all devices as shown above.

8. Switch everything on in the following order.

i. audio input sources (i.e. microphones, instruments, CD/MP3 Players)

ii. TAILGATER

iii. any additional amplifiers

9. When shutting down, always reverse this operation by turning off:

i. any additional amplifiers

ii. TAILGATER

iii. audio input sources (i.e. microphones, instruments, CD/MP3 Players)

Go to http://www.ion-audio.com

for product registration.

BOX CONTENTS

 Battery Powered Amplifier
 (1) Microphone with Cable
 (1) Power Cable (standard IEC)

To input on

additional

TAILGATER

(Cable sold
separately)

(Cable sold separately)

OR

1

DIAGRAM AND PARTS DESCRIPTION

1. Microphone 1 Balanced
Input with Gain Control
(1/4” or XLR): This jack can

take either a ¼” balanced or
a XLR balanced cable.

2. Instrument/Microphone 2

Input with Gain Control
(1/4”): This mono input

accepts a ¼” input such as a
microphone, guitar, or other
musical instrument.

3. iPod/Auxuliary input with

Gain Control (Stereo
RCA): This stereo RCA

input can be used to connect a CD, MP3, or other audio source. The knob controls the level of the iPod and
the RCA input. To connect to a portable device with a 1/8” headphone jack, you need a standard 1/8”-to-RCA
adapter which is not included.

4. Master Volume Control: This knob controls the master volume of the TAILGATER.

5. iPod Charging Switch: Turn on iPod charging by setting this switch to the "Charge iPod" position.

6. Battery Level Indicator: While the unit is powered ON, these four lights indicate the power left in the battery.
Battery life varies based on volume and usage.

7. Link Output: Connect a 1/4" stereo (TRS) cable to this line-level output to connect another amplifcation
device, such as another TAILGATER.

8. Power In (IEC): Insert the included power cable here to charge the unit. Note that the TAILGATER can run off
wall power while it simultaneously charges the battery. The charge indicator illuminates when the battery is
charging.

9. Voltage Selector*: Set this to the correct voltage for your
location's standard.

10. Power ON/OFF Switch: Turns TAILGATER on or off.
Please note that while TAILGATER is connected to a
power source, it does not need to be powered on to
charge the battery.

1

5

6

7

* WARNING: U.S. users should set this
switch to "100-120V" whereas U.K. and most
European users should set this to "220­240V."Selecting the improper voltage can

damage the unit.

324

10

8

9

IMPORTANT NOTES

If your sound is distorted at high volumes, please refer to the following troubleshooting scenarios:

• Input is clipping: Try lowering the input gain or the volume control on your sound source or music instrument.

• Output is clipping: Lower the main volume level.

• There is too much bass: Try adjusting the tone or EQ control on your sound source to lower the bass level.

This will allow you to play the music louder before clipping (distortion) occurs.

• The link cable: is being plugged into the instrument or MIC input instead of the RCA line input.

Important: With all speakers, an initial “break-in” period is needed to perform at optimal levels. To properly “break­in” your TAILGATER, play an audio source at medium volume for a few hours.

SPECIFICATIONS

Input Voltage: AC 100-120V/ 60Hz 220-240V/ 50Hz
Output Wattage: 16W (THD: < 1%)
Output Voltage: 8V/4Ω
Frequency Response: Aux Input: 78Hz – 80kHz

iPod Input: 63Hz – 77kHz

Time required to fully charge the TAILGATER: ~ 6 hrs.
Battery life: 12 hrs. with typical use (at 2/3 volume)

* Note: Battery life may vary
based on temperature, age,
and volume usage of product.

2

MANUAL DE INICIO RÁPIDO (ESPAÑOL)

1. Asegúrese que todos los artículos incluidos al inicio de este manual
estén incluidos en la caja.

2. LEA LAS INSTRUCCIONES DEL FOLLETO DE SEGURIDAD ANTES

DE UTILIZAR EL PRODUCTO.

3. ASEGÚRESE DE QUE HA CARGADO COMPLETAMENTE LA
BATERÍA. PARA LOGRAR LA MÁXIMA VIDA ÚTIL DE LA
BATERÍA, CÁRGUELA TOTALMENTE ANTES DEL PRIMER USO.

4. Estudie este diagrama de instalación.

5. Coloque el producto en una posición adecuada para su funcionamiento.

6. Asegúrese de que todos los dispositivos de entrada tales como micrófonos, reproductores de CD, reproductores MP3 y
amplificadores/sistemas de amplificadores para altavoces estén apagados y con el control de volumen en “cero”.

7. Conecte todos los dispositivos como se muestra arriba.

8. Encienda todo en el siguiente orden:

i. fuentes de entrada de audio (por ejemplo, micrófonos, instrumentos, reproductores de CD/MP3)

ii. TAILGATER

iii. amplificadores adicionales

9. Al apagar, realice siempre esta operación en sentido inverso. Apague:

i. amplificadores adicionales

ii. TAILGATER

iii. fuentes de entrada de audio (por ejemplo, micrófonos, instrumentos, reproductores de CD/MP3)

Visite http://www.ion-audio.com para registrar el producto.

CONTENIDO DE LA CAJA

 Amplificador alimentado
 (1) micrófono con cable
 (1) cable de alimentación

A entrado en

TAILGATER

adicional

(Cable vendido

por separado)

Cable vendido por separado

O

3