Ioline I/S 60, I/S 130, I/S 100 System, SC-40, I/S 85 Quick Start Manual

1

Quick Start Guide

I/S Series SC Series

I/S 60, 85, 110, 130 and 100 System SC-40 & -48

Ioline SmarTrac™

2

User Notice

Trademarks

Ioline and SmarTrac are trademarks of Ioline Corporation. Other product names, logos, designs, titles, words or
phrases mentioned within this publication may be trademarks, service marks, or trade names of Ioline Corporation or
other entities and may be registered in certain jurisdictions including internationally.

Ioline Disclaimer

IOLINE CORPORATION PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL IOLINE, ITS DIREC­TORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF
USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF IOLINE HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

Limit of Liability Statement

It is the responsibility of the operator of the cutter to monitor the performance of the cutter and maintain it in proper
working condition by following the instructions in this User Guide. It is the responsibility of the operator of the cutter
to follow all safety precautions and warnings that are described in this User Guide. Ioline is not responsible for inju­ries that may occur as a result of unsafe operating procedures. Ioline is not responsible for substandard operational
performance as a result of failure to maintain the cutter as described in this User Guide.

© 1997-2005 Ioline Corporation. All rights reserved. This manual may not be copied, photocopied, reproduced, trans­lated, transmitted or converted to any electronic or machine-readable form in whole or in part without prior written
approval of Ioline Corporation.

Service and Support

If you require assistance with an Ioline product, your local Ioline dealer or authorized service center is ready to help.
Support information is also available 24/7 on the Ioline Web site—or you may contact Ioline directly:

Ioline Corporation

14140 NE 200th Street

Woodinville, Washington 98072 U.S.A.

Ioline Customer Service Department

Monday through Friday

7:00 A.M. - 5:00 P.M. U.S. Pacic Time

Voice: 1.425.398.8282

Fax: [phone]

[e-mail]

www.ioline.com

Part Numbers: (Print) 106916 Rev. 8 • (File) 107109 Rev. 5

Please read these safety guidelines before beginning operation of
the cutter. The cutter uses a very sharp blade when cutting. The
parts can move quickly. Always observe the following safety pre­cautions:

n Do not allow the material to become suddenly taut between

the cutter and a roll of material during plotting. A service
loop of unrolled material is required for problem-free opera­tion. Using the Autoloop function (enabled in the Control
Center) will create the required service loop by gently pulling
a set amount of material from the roll before cutting. Ioline
recommends using the Autoloop function when plotting on a
roll of material.

Safety &

Cautions

n Do not try to repair the machine without factory authorization.

Only qualied service personnel should attempt any disas­sembly or access to internal components. If external mechanical
adjustments are necessary, turn off the cutter and disconnect it
from all power sources (both the computer and the wall outlet).

n Be careful with hair, jewelry, or loose clothing near the cutter.

They can become caught in the mechanical parts.

n Never move the carriage by hand. Use the Arrow keys and let

the machine do it.

n Keep hands away from the carriage when the cutter is in opera-

tion. The carriage will automatically move to its right end posi­tion when the power is turned on.

n Be careful when lifting the cutter. Hold the bottom surfaces of

the cutter to lift or move it.

n Keep ngers away from the drive shaft when the cutter is in

operation.

n Use caution when changing a blade in the blade holder. See the

Routine Maintenance chapter of the SmarTrac User Guide for the
recommended procedure.

n Be careful when handling the blades. They are sharp and could

cause an injury if mishandled. Although the blades are made
of an extremely hard material, they are brittle and can break if
dropped or mishandled.

4

KEY

O

N

A. Dust Cover
B. Drive Shaft Marker
C. Carriage
D. Blade Holder

A B H

E. Idler Wheel
F. Drive Shaft
G. Pinchwheel
H. Pinchwheel Lever

E

I

J

M

L

K

G

F

Figure 1. The Ioline SmarTrac I/S Cutter Front View.

C

D