IOGear GDIP201 User Manual

Installation

Installation Guide

Installation

DVI Net ShareStation

GDIP201

PART NO. M1048

Table of Contents

Package Contents 4

Hardware Installation 5

USB Server software installation - XP 10

DisplayLink software installation XP 14

GDIP201 Full Software Installation - XP 18

Windows XP utility Setup 21

Connecting to a DVI Monitor - XP 25

Video Mode conﬁ guration - XP 28

Disconnecting the GDIP201 - XP 34

USB Server Software Installation - Vista 35

DisplayLink software installation - Vista 39

GDIP201 Full Software installation - Vista 43

GDIP201 Conﬁ guration - Vista 48

Connect to DVI Net ShareStation – Vista 52

Video Mode conﬁ guration - Vista 54

Disconnect the GDIP201 in - Vista 59

Setting Polling Interval - XP 60

Web Management Interface 61

Upload Firmware 64

Federal Communications Commission (FCC) Statement

CE Statement 70

Limited Warranty 71

Contact 72

Package Contents

Verify that nothing is missing from the package by using the checklist below. Please contact your dealer if anything is missing or damaged. All packing materials are recyclable. Please conﬁ rm the items in the package below:

1 x DVI Net ShareStation

1 x RJ45 Ethernet Cable

1 x USB Cable

1 x User Manual

1 x Installation CD

1 x Warranty/Registration Card

1 x Power Adapter

1 x US-Euro Prong Changer

1 x DVI to VGA Adapter

Hardware Installation

*Make sure that your DVI monitor is powered off and that the server’s power adapter is disconnected before the installation.

1. Connect the DVI Net ShareStation to your router or switch with the included RJ45 Ethernet cable.

If your home or ofﬁ ce already has a pre-installed network, you may connect the DVI Net ShareStation to the RJ45 jack on the wall with the included RJ45 Ethernet cable.

DSL MODEM

2. Connect the DVI cable of the DVI monitor to the DVI port on the DVI Net ShareStation.

3. Connect the power adapter to the DVI Net ShareStation and make sure it is powered on. When the Link indicator lights up, the DVI Net ShareStation is correctly connected to the network.

Before you start the software installation,

If this is the ﬁ rst time you are installing the GDIP201 software please proceed to page 18

If you had purchased the IOGEAR GUC2020D and installed DisplayLink software, then you will only need to install the IOGEAR USB Server software.

• Please see page 10 for Windows XP installation.

• Please see page 35 for Windows Vista installation.

If you had purchased the IOGEAR GUIP201 and installed the IOGEAR USB Server software installed, then you will only need to install the DisplayLink software.

• Please see page 14 for Windows XP installation.

• Please see page 39 for Windows Vista installation.

USB Server Software Installation - XP

1. Insert the GDIP201 installation disk into the CD-ROM drive, which will bring up the auto run screen menu.

Click the Exit button to close the auto run screen.

2. Go to My Computer which can be located by double clicking on the My Computer icon on your desktop.

3. Right click on the CD-ROM drive and select

Explore.

4. Double click on the folder that corresponds to your operating system.

Double click on the setup icon to install the IOGEAR utility.

5. The installation wizard will start the installation process, click “Next” to continue.

6. When the installation completes, click

“Finish” to close the installation wizard.

DisplayLink- software installation XP

1. Insert the GDIP201 installation disk which will bring up the auto run screen menu.

Click the Exit button to close the auto run screen.

2. Go to My Computer which can be located by double clicking on the My Computer icon on your desktop.

3. Right click on the CD-ROM drive and select Explore.

4. Double click on the DL_Driver folder

5. To start the DisplayLink software installation you will need to double click on the Setup icon.

6. The installation program will start, click

I Accept to continue

7. The DisplayLink software is now installing

GDIP201 Full Software Installation - XP

This section will guide you through the complete GDIP201 software installation.

1. Insert the Software CD into your computer. A splash screen should appear with a menu of options. Click on “Windows XP installation” to set up the DVI Net ShareStation’s control center software.

2. The installation wizard will start the

installation process, click “Next” to continue.

3. When the installation completes, click

“Finish” to close the installation wizard

DisplayLink installation

4. To start the DisplayLink installation, click

I Accept to continue

5. The DisplayLink software is now installing

Windows XP Utility Setup

1. Once you have completed both the IOGEAR and the DisplayLink software installation you will be ready to use the GDIP201.

You will ﬁ nd a new icon on your desktop called “Launch IOGEAR USB server”, double click the icon and it will bring up the IOGEAR USB server conﬁ guration utility.

2. Once the IOGEAR utility is launched, Windows will prompt you with a “Found New Hardware Wizard” window. You will need to complete the wizard so that you will be able to use the DVI Net ShareStation on your computer

Select “No, not this time” and click on

Next to continue.

3. Click on “Install the software automati- cally (Recommended)” and click Next to continue.

4. Windows will install the necessary drivers for the DVI Net ShareStation.

5. Select Finish to complete the wizard.

+ 51 hidden pages