IOGear Q1042, GBMA211 User Manual

Warranty Information

About Us

Quick Start

Bluetooth®•Stereo Audio Transmitter

•Stereo Audio Transmitter

rge

ack

Package Contents

FRONT

This product carries a 1 Year Limited Warranty. For the terms and conditions of
this warranty, please go to http://www.iogear.com/support/warranty or call
1-866-946-4327(U.S. only) or [phone].

Register online at http://www.iogear.com/register

Important Product Information

Product Model _________________

Serial # _______________________

Contact

Toll Free 866-9-IOGEAR (USA)
Phone: [phone]
23 Hubble
Irvine, CA 92618 USA
www.iogear.com
[e-mail]

About Us

About Us

FUN

IOGEAR offers connectivity solutions that are innovative, fun, and stylish,
helping people enjoy daily life using our high technology products.

GREEN

IOGEAR is an environmentally conscious company that emphasizes the
importance of conserving natural resources. The use of our technology
solutions helps reduce electronic waste.

HEALTH

IOGEAR supports healthy and fit lifestyles. By integrating products with
the latest scientific developments, IOGEAR’s solutions enhance the life of
end-users.

Quick Start Guide

Bluetooth

1 Bluetooth® Stereo Audio Transmitter
1 Mini USB 4 Pin Charging Cable
1 3.5mm to ¼” Adapter
1 3.5mm Audio Extension Cable
1 Full Range Power Adapter
1 European Prong Changer
1 Quick Start Guide
1 Warranty / Registration Card

System Requirements

• Available 3.5mm or ¼” Audio Jack

• A2DP supported Bluetooth Stereo Headphone or Speaker

BACK

Overview

1. Blue / Red LED

2. ON / OFF Button

3. 3.5mm Audio Connector

4. Mini-USB 4 pin Charger Jack

a

r J

4

Start Here!

1

2

3

Charging GBMA211

Note: You have to fully charge the batteries for 6 hours before initial usage.

1. Connect the mini USB charging cable to the GBMA211 and any open USB
port on your PC. You can also charge GBMA211 via AC adapter.

2. The LED on the GBMA211 will light up in red indicating that it is being
charged.

3. When the charging is completed, the red LED will go off.

Note: Please connect the cable directly to your PC and avoid connecting it

through other devices, such as a USB hub.

© 2008 IOGEAR, INC.

Pairing with GBMA211

1. Hold ON / OFF Button for 7 seconds on your GBMA211 when it is in OFF mode
to activate the pairing mode. GBMA211’s LED will be flashing blue and red
alternately.

2. Activate the pairing mode on your Bluetooth Headset / Headphone. (Please
refer to your Bluetooth Headset / Headphone’s user manual on how to activate
pairing mode.)

3. Wait for the GBMA211’s LED to flash blue only to confirm that the two devices
are connected to each other. Then you should be able to listen to music
through GBMA211 with your Bluetooth Headset / Headphone. (For example,
you can test to see if the GBMA211 is paired by plugging the 3.5mm or ¼”
audio connector to your PC’s audio output. Then use any audio software to play
your music to see you can hear any audio sound from your Bluetooth Headset /
Headphone.)

Connecting GBMA211 with audio source

1. Plug GBMA211 into the 3.5mm or ¼” audio jack of MP3 player or any audio
source.

PART NO. Q1042

2. Turn on GBMA211.

3. Turn on your Bluetooth Headset / Headphone and wait for the blue LED to
flash normally, then the two devices are successfully connected. (If
GBMA211 cannot reconnect to any device after turning on for 1 minute, it
will turn off automatically. Then please turn off both devices and move the
device closer to each other then repeat step 3.)

Note: GBMA211 can only reconnect to the last connected device. If you have

paired with another device before the one you currently want to use,
please go to Pairing with GBMA211 to re-pair the device.

4. Now, you should be able to listen to music from the MP3 player or any audio
source.

5. Use the audio source’s Volume Up / Down control button to adjust the
volume.

Note: You have to pair GBMA211 and the Bluetooth Headset / Headphone if

you are trying to connect them for the first time. After the initial pairing
process, GBMA211 will search and re-connect with the Bluetooth
Headset / Headphone on standby status. (Please refer to Pairing with
GBMA211 if you need to pair your Bluetooth device with GBMA211.)

GBMA211

Operation

Function Button

ON Hold ON / OFF for 3 second when it’s OFF

OFF Hold ON / OFF for 6 second when it’s ON

Pairing Hold ON / OFF for 7 second when it’s OFF

LED Definition Description

Connected Flash normally

Blue LED

Red LED

Blue and Red LED Paring Mode

Note: Before initial usage, we recommend that you fully charge GBMA211 for at

least 2 hours.

Waiting to connect

Power On

Charging

Charging completed

Low battery

Power Off

Flash slowly

Flash 3 times quickly

On

Off

Flash quickly every 5 second

Flash 3 times quickly

Blue LED and Red LED flash
alternately