In Win IW-RJ316-04, IW-RJ212-04 User Manual
IW-RJ316-04
User’s Manual
Table of Contents
PREFACE .......................................................................................................................................... 1
SAFETY INFORMATION ................................................................................................................... 1
CAUTION ......................................................................................................................................... 2
SPECIFICATIONS .............................................................................................................................. 3
1 Product Introduction ............................................................................................................... 4
1.1 Box Contents ............................................................................................................................ 4
1.2 General Information ................................................................................................................ 5
1.2.1 Front Panel Controls and Indicators ............................................................................. 6
1.2.2 Rear Panel Configuration ............................................................................................. 7
1.2.2.1 Expander Configuration ........................................................................................... 7
2 Hardware Installation ............................................................................................................. 8
2.1 Removing and Installing a Hard Drive ................................................................................... 8
2.1.1 Installing a Hard Drive .................................................................................................. 8
2.1.2 Removing a Hard Drive ................................................................................................ 9
2.2 Removing and Installing the Fan Module .............................................................................. 9
2.2.1 Removing the Fan Module ........................................................................................... 9
2.2.2 Installing the Fan Module ........................................................................................... 10
2.3 Removing and Installing the PSU Module ............................................................................10
2.3.1 Removing the PSU Module ........................................................................................ 10
2.3.2 Installing the PSU Module .......................................................................................... 11
2.4 Removing and Installing the Expander Module...................................................................12
2.4.1 Removing the Expander Module ................................................................................ 12
2.4.2 Installing the Expander Module ................................................................................. 13
2.5 Rail Installation .......................................................................................................................13
2.5.1 The Type of Rail Kit .................................................................................................... 13
2.5.2 Fixed Rails .................................................................................................................. 13
2.5.3 Slide Rail .................................................................................................................... 14
2.5.3.1 Take out the Inner Rail and Slide the Intermediate Rail Back .................................. 14
2.5.3.2 Attach the Inner Rail to the Chassis ........................................................................ 14
2.5.3.3 Mount the Rail Bracket to the Cabinet ................................................................... 15
2.5.4 Insert the Chassis to the Cabinet ................................................................................ 16
3 Expander Board Introduction ................................................................................................ 17
4 Ethernet Management Card Introduction ............................................................................. 18
5 User Interface Introduction ................................................................................................... 19
5.1 Overview ..................................................................................................................................19
5.2 Key Features ............................................................................................................................19
5.3 Software Management...........................................................................................................20
5.3.1 System Management Structure .................................................................................. 20
5.3.2 Serial Port Management ............................................................................................ 25
5.3.3 Network Management ............................................................................................... 29
5.3.4 Version Information ................................................................................................... 35
5.3.5 System Status............................................................................................................. 38
5.3.6 Network Settings ....................................................................................................... 40
5.3.7 Disk Information ........................................................................................................ 41
5.3.8 Zone Setting ............................................................................................................... 43
5.3.9 Firmware Upgrade ..................................................................................................... 46
5.3.10 System Logs ........................................................................................................... 54
6 Compatibility Lists ................................................................................................................ 58
7 Q&A ...................................................................................................................................... 58
8 Technical Support .................................................................................................................. 60
1
PREFACE
Thank you for choosing In Win IW-RJ316-04. This manual is written for system technicians who are
responsible for installation, troubleshooting, managing and repairing this server chassis. This
document provides the overview of all the features of the chassis, a list of accessories or other
components you may need to finish the installation, troubleshooting methods and instructions on
adding and removing components on the In Win IW- RJ316-04. For the latest version of this
manual, you may visit In Win’s server website to download the latest updated version.
SAFETY INFORMATION
To ensure a safe and smooth operation of your In Win IW-RJ316-04, it is essential that you choose
an appropriate location for the system, provide an appropriate operating environment and supply
an adequate amount power for all components of the system. As you plan for installation, follow
the guidelines below to ensure that the system and its environment are safely and appropriately
positioned for efficient operation and service. Your system should be installed and serviced only by
a qualified technician.
Environment selection: The system is designed to operate in a typical office environment:
• The location should be clean, dry and free of airborne particles.
• It should be a well-ventilated room, and away from sources of heat including direct sunlight
and radiators.
• It should be kept away from sources of vibration or physical shock.
• The space should be accommodated with a properly grounded wall outlet, and with sufficient
space to access the power supply cords.
• The operating environment temperature should be around 0°C to 40°C (32°F to 104°F).
Heed safety instructions: Before working with In Win IPC/Storage server products, we strongly
recommend you use this guide as a reference and follow the safety instructions. The instructions in
this manual will help you ensure and maintain compliance with existing product certifications and
approvals. Follow the described, regulated components mentioned in this manual. Use of non-UL
listing products or other regulators may not comply with product regulations in the region(s) in
which the product is sold.
System power on/off: The power button DOES NOT totally turn off the system AC power. To
remove the power of the system, you must unplug the AC power cord from the outlet or the
system’s power supply units. Make sure the power cord is unplugged before you open the chassis,
add or remove any components.
Hazardous conditions, devices and cables: Hazardous electrical conditions can be present on/in
power supply units and their cables. Disconnect the power cord and any other device attached to
the server before opening the case. Failing to follow safety procedures will increase the risk of
personal injury or equipment damage.
2
Electrostatic discharge (ESD) and ESD protection: In most cases, ESD may damage disk drives,
electronic boards and other parts. We recommend that you conduct installation only at an ESD
free space. If not possible, perform ESD protection protocol by wearing an anti-static wrist straps
attached to the ground on any unpainted metal surface on your server during operation.
Installing or removing jumpers: A jumper is a short length conductor used to close, open or bypass
part of an electronic circuit. Jumpers on In Win backplanes have a small tab on top that you can
pick up with your fingertips. Grip the jumper carefully, and plug the jumper to cover the jumper
pins on the backplane. Once you need to remove the jumper, grip the jumper and carefully pull
without squeezing.
CAUTION
To avoid damage and maintain your safety, please read the following terms listed below:
1. No to populate hard drives and turn on the power before the system is settles
down.
Make sure hard drives and other components are properly connected before
turning on the system.
2. Tighten or loosen all the screws with a screwdriver.
3. Apply the correct screws packed in the accessory box.
4. For your safety, please have at least two people lift and place the unit.
5. Before mounting the unit to the cabinet, make sure the rail is installed correctly.
6. When installing and removing any module or part, please use the handles.
3
SPECIFICATIONS
Model Name
IW-RJ316-04
Standard
EIA-RS310D
Dimensions (D x W x H)
w/o Front Door
520.7 x 482.6 x 131 mm
(20.5" x 19" x 5.25")
Storage
External: Hot-swap 3.5" x 16 (SAS 12Gbps)
Maximum Capacity
Up to 128 TB
(Cascades to 3 enclosures with 48 HDDs, including 1 host server)
Power Supply
Supports
▪ Form Factor: Platinum CRPS redundant
▪ Watt: 550W
Cooling Fan
8038mm x 4
SAS 12G Module
1 or 2
Host/Expansion Port
3 x Mini SAS HD (SFF-8644) for each 12G expander module
Management
Smart fan, thermal monitor, HDD monitor, voltage monitor, alarm
warning
SES
Supports SES-2 (SCSI Enclosure Service)
Maintenance
Supports management by Ethernet (Optional) and RS-232
HDD Power Management
HDD sequential power on
Temperature
0ºC to 35ºC
Material
Material: SGCC
Thickness: 1.0 mm
Rail Kit
Fixed rail included.
(Optional 20" tool-less & ball-bearing slide rail)
* The actual product is subject to change without prior notice. In Win Development Inc. reserves the
right to make any final modifications.
4
1 Product Introduction
1.1 Box Contents
5
1.2 General Information
IW-RJ316-04 JBOD enclosure is a 3U rackmount storage chassis with 16 tray-less bays, dual
expander module, dual fan module, and redundant 550W power supply. IW-RJ316-04 is capable
of providing ample storage, while allowing users to cascade 3 enclosures with 48 HDDs,
including 1 host server.
6
1.2.1 Front Panel Controls and Indicators
The front panel control buttons and LED indicators are located on the top left handle.
No.
Name
Color
Status
Description
1
Power On/Off Button
with LED
Blue
Solid on
System is powered on
N/A
Off
System is not powered on
2
Mute Button
N/A
Press the button to turn off the beeper
3
Chassis ID Button with
LED
Blue
Solid on
Press the button to activate system
identification
4
System Fail LED
Red
Solid on
System Fault (Beeper)
❶ ❷ ❹
❸
7
1.2.2 Rear Panel Configuration
No.
Item
No.
Item
1
Power Module 1
4
Fan Module 2
2
Power Module 2
5
Secondary Expander Module
3
Fan Module 1
6
Primary Expander Module
1.2.2.1 Expander Configuration
No.
Name
Color
Status
Description
1
Chassis ID button with
LED
Blue
Solid on
Press the button to activate
system identification
2
Uplink SAS Port
N/A
Host HBA/RAID card connection
3
Downlink Expander Port
N/A
External cascading
4
Expander Module Status
LED
Blue
Blink
Normal
Blue
No Blinking
Abnormal
5
RS-232 Port
N/A
Debug console connection
6
LAN
N/A
Ethernet remote monitoring
(optional)
❶ ❸ ❷ ❹ ❺
❻
❻
❶ ❷ ❸ ❹ ❺
8
2 Hardware Installation
2.1 Removing and Installing a Hard Drive
IW-RJ series JBOD features tool-less trays. Users no longer need to use screws to mount
disks, and can swap drives faster.
2.1.1 Installing a Hard Drive
Step 1: Press the release button then pull outward on the handle.
Step 2: Place the 3.5" HDD into the tray.
Align the HDD screw with the two pins on the side of the tray.
Press the other side of HDD downward to the tray.
Step 3: Insert the HDD tray to the slot.
Step 4: Push back the lever until it clicks.
Step 1
Step 2
Step 3
Step 4
Press
Pull
Push
Insert the HDD
9
2.1.2 Removing a Hard Drive
Step 1: Press the release button then pull outward on the handle.
Step 2: Press the HDD out of the bottom of the tray with your fingers.
Step 3: Pull out the hard drive.
Step 1
Step 2
Step 3
2.2 Removing and Installing the Fan Module
IW-RJ series JBOD has built-in dual fan modules that support hot-swappable and
redundant features. With a tool-less design, IW-RJ series JBOD is easy to maintain.
2.2.1 Removing the Fan Module
Step 1: Press the clip to release the fan slot.
Step 2: Pull out the fan module from the fan slot.
Press
Pull
Push
10
Step 1
Step 2
2.2.2 Installing the Fan Module
Step 1: Push the fan module back into the slot until it clicks.
Step 2: Connect the fan to the backplane.
Step 1
2.3 Removing and Installing the PSU Module
The IW-RJ316-04 hosts a built-in redundant power supply module. With this function,
the system is capable of still functioning if one of the modules fail. To replace it, the user
only needs to release the failed module, then insert a functional module.
2.3.1 Removing the PSU Module
Step 1: Press the release tab of the power supply unit’s module at the back.
Step 2: Pull the module out using the handle.
Pull
Press
Push
11
Step 1
Step 2
2.3.2 Installing the PSU Module
Step 1: Make sure the label is facing upward, and push the power supply module
into the cage until it clicks.
NOTE: 1. The unit supports In Win PSU modules only, please do not attempt to insert any
other brands of modules.
2. The two PSU modules’ output wattage must be the same.
Pull
Push
Press
Press
12
2.4 Removing and Installing the Expander Module
In Win IW-RJ series JBOD contains a set of redundant expander modules. The bottom
module is the primary expander, while the upper is the secondary. The primary
expander module includes an Ethernet management module, which allow users to
monitor and manage the system through Ethernet. Also, the redundant module can
minimize downtime should any on the expanders fail.
2.4.1 Removing the Expander Module
Step 1: Press the clip of the expander module and swivel the handle outward.
Step 2: Pull out the expander module.
Step 1
Step 2
Push
Press
13
2.4.2 Installing the Expander Module
Step 1: Push the expander module into the cage until it clicks back the original
location.
Step 2: Swivel the handle back to lock into position.
Step 1
2.5 Rail Installation
IW-RJ series JBOD is a rackmount model, which support EIA-RS310D standard cabinets
and chassis racks. In Win provides standard fixed rails or optional slide rails for mounting
the JBOD chassis to cabinets.
2.5.1 The Type of Rail Kit
Please follow the instructions to install the rails on the cabinet or chassis rack
according to the rail type you ordered.
2.5.2 Fixed Rails
Step 1: Insert the fixed rail into the rail bracket from the end of the chassis.
Step 2: Tighten the screws to secure the rail and the chassis on the cabinet.
Step 3: Repeat the same action on the other side.
Step 1
Pull
Insert
Insert
14
2.5.3 Slide Rail
2.5.3.1 Take out the Inner Rail and Slide the Intermediate Rail Back
Step 1: Pull out the inner rail until it reaches the stop. Release the blue
slide tab to unlock.
Step 2: Continue pulling the inner rail until the second stops. Release the
white slide tab to remove the inner rail.
Step 3: Pull the latch on the middle rail upward and retract the middle rail
back.
Step 1~2 Step 3
2.5.3.2 Attach the Inner Rail to the Chassis
Step 1: Remove the fixed rail brackets on both sides to reveal the
standoffs.
Step 2: Align the chassis sidewall standoffs to the inner rail keyholes. Slide
the inner rail toward the front until the standoff snaps into place,
securing the rail to the chassis.
Step 3: Repeat the same action on the other side.
Step 4: When removing the inner rail:
Pull up the latch and slide the inner rail forward. Remove the
keyhole from the standoff to detach the inner rail. (Action and
❖ in the figure)
Step 1
15
Step 2
Step 4
2.5.3.3 Mount the Rail Bracket to the Cabinet
Step 1: Extend the rail bracket over the rear rack of the cabinet.
Step 2: Pull out the rear hook on the end of the outer rail, align and push
the rail bracket pins into the post holes on the rack. Then, pull
back the hook on the end of the outer rail.
Step 3: Extend the opposite side of the rail bracket to the front rack of the
cabinet.
Step 4: Hang the front hooks of the outer rail at the front of the rack post
holes. Pull the rail bracket pins that go into the front post holes on
the rack until they click.
Step 5: The other side of the rail is symmetrical, repeat the installation
steps 1-4.
Step 6: Once you would like to detach the bracket, pull outward on the
front and rear hooks of the outer rail to release the bracket.
Repeat the same action to the other side.
Step 1~4
16
Step 6
2.5.4 Insert the Chassis to the Cabinet
Step 1: Pull out the middle rail to the stop position.
Step 2: Move the ball bearing retainer to the front end of the middle rail, it should
click into the locked position.
Step 3: Insert the inner rails of the chassis into the middle rails on the both sides of
the rack.
Step 4: Push the chassis to the stop position, then release the blue slide tab (by
either pulling the tab forward or pushing the tab back) to continue.
Step 5: Until reaching the second stop position, release the blue slide tab again to
continue.
Step 6: Push the chassis into position on the rack completely. Make sure that the
front end of the chassis is aligned with the edge of the rack to complete
the installation.
Loading...