Series 2800
Custom S-Pen Charger
Vertical Recoiler
DNAZ72
Clean the xture with the provided
1
alcohol wipe. Let it dry completely.
Optional:
2
If desired, route the cable through a
hole or slot in the xture.
Peel the liners from the adhesives on
3
the bottom of the recoiler.
Place the recoiler in the desired
4
location and apply pressure for at 10
least seconds.
Pull the sylus clip from the recoiler.
5
Remove the pin cover from the fob
6
tool.
Insert the pin into the hole opposite
7a
of the cable.
Pivot the fob tool back to remove the
7b
retainer.
Remove the sleeve and separate the
8
upper and lower halves of the stylus
clip.
Prepare the stylus for installation
9a
into the clip by making sure that it is
clicked open.
With the S-Pen clicked open, place
9b
it into the cavity of the bottom clam
shell piece. The button on the S-Pen
should face upwards.
Place the top half of the clam shell
10
over the S-Pen.
Orient the sleeve cover so that the
11
gap will align with the cable. Slide
the sleeve up the length of the S-Pen
and over the the 2 pieces of the
stylus clip.
Cable
Gap
Insert the retainer into the hole on the
12
outer sleeve and through the bottom
piece of the clip. It should sit ush
when properly assembled.
Insert the S-Pen into the hole in the
13
top of the recoiler to display.
Power Only: Plug the supplied USB-
14
C cable into the side of the power
injection port.
Plug the USB-A end of the power
15 16
cable into a power supply (InVue’s
PS515 or an OEM travel adapter).
Plug the power supply into a power
outlet.
Optional: If Alarming fuctionality is
desired, plug the micro-USB end of
the cable into a preinstalled S2800,
S2865 or Zips 2.0 unit.
If the micro-USB end of the cable
17
was plugged in to provide alarming
function, the LED on the sensor will
be illuminated to indicate that the
alarm circuit is armed.
The LED on the recoiler will illuminate
18
to indicate the S-Pen is charging
when fully docked as shown and will
turn off when it is removed.
FCC WARNING STATEMENT
FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation. FCC Part 15.21 Any changes or modications (including the antennas) to this device that are not expressly
approved by the manufacturer may void the user’s authority to operate the equipment.
FCC RADIATION EXPOSURE STATEMENT
(Wireless Charger Dock)
This equipment complies with FCC Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna
must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and your body.
IC WARNING STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage, et (2)
L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
IC RADIATION EXPOSURE STATEMENT
(Wireless Charger Dock)
This equipment complies with IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna
must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and your body. Cet équipement est conforme aux limites établies par
Industrie Canada en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Cet appareil etson antenne ne
doivent pas être colocalisés ou fonctionner en conjonction avec tout autre antenne ou émetteur. Cet équipement doit être installé et
utilisé avec une distance minimale de 20cm entre le radiateur et votre corps.
SD0612 Rev5 07/11a/18
www.invue.com
NA / LATAM // 70 4.75 2.6513 • 888.55.INVUE
EMEA // +31.23.8 90 0150
APAC // +852.3127.6811
© 2018 InVue Security Products Inc. All rights reserved.
InVue is a registered trademark of InVue Security Products.
Loading...