Involight BATBAR230 User Manual [ru]

INVOLIGHT BATBAR230

USER MANUAL

Battery Powered DMX LED Bar, 240*10mm RGB, 8 Sections

User Manual

Our Battery Powered DMX LED Bar offers very nice and bright effect for performance stages where traditional
stage lighting emits a lot of heat onto performers. Very smooth field with rich palettes of color created by mixing
the Red, Green and Blue LEDs. Please read the manual before operation.

A. SPECIFICATION

1. Voltage: AC 100V-240V, 60Hz/50Hz

2. Power Consumption: 42W

3. LED: 240*10mm (R96, G72, B72)

4. Beam Angle: 30°

5. Working temperature: -10~40℃

6. Control Feature: Built-in programs, Auto running, DMX 512, Master/slave mode, Static color and Charge mode

7. DMX channels: 3, 5, 24, 2, 7 CH

8. N.W: 4.36kgs

9. Dimension: 1073*120*135 mm

10. Stand by time: 3.5 hours（RGB）

11. Charging time: 6 hours

12. Lumen: R: 110lux /2m
G: 234lux /2m
B: 250lux /2m
RGB: 490lux /2m

B. OPERATION

This fixture is with rich effect programs, LED dislay for easier operation, there are seven working modes:

1. Built-in Program Mode

This mode is built-in programs mode, it is static color program when the display board shows , then press
SETUP button to set the static colors via UP or DOWN buttons. Press SETUP button again to set the strobe value
of the static colors via UP or DOWN buttons - .

Press SETUP button could set the speed - and strobe value - when the display
board shows ~

2. Auto running Mode

CH1

CH2

CH3

R(0~255)

G(0~255)

B(0~255)

CH1

CH2

CH3

CH4

CH5

R(0~255)

G(0~255)

B(0~255)

Dimmer(0~255)

Strobe(0~255)

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

R1

G1

B1

R2

G2

B2

R3

G3

B3

R4

G4

B4

0~255

0~255

0~255

0~255

0~255

0~255

0~255

0~255

0~255

0~255

0~255

0~255

CH13

CH14

CH15

CH16

CH7

CH18

CH19

CH20

CH21

CH22

CH23

CH24

R5

G5

B5

R6

G6

B6

R7

G7

B7

R8

G8

B8

0~255

0~255

0~255

0~255

0~255

0~255

0~255

0~255

0~255

0~255

0~255

0~255

CH1

CH2

Program

Speed

Pr.01

0~11

0-27(OFF)

28-55(R)

56-83(RG)

84-111(RG)

112-139(G)

140-167(GB)

168-195(B)

196-223(RB)

224-251(RB)

252-255(RGB)

This mode is Auto Running mode, the fixture will automatically run the programs according to the
present programs - .

3. M/S Mode

This mode is M/S Mode, the salve fixtures will follow the programs after they were linked to the master fixture via
DMX cables.

4. DMX Mode

It is DMX mode when the display board shows , the address could be set via UP and DOWN buttons, the
maximum value is 512.
Press the “UP” or “DOWN” button, set the DMX working modes: 3, 5, 24, 2, 7CH

DMX Mode 1：3-ch

DMX Mode 2：5-ch

DMX Mode 3：24ch

DMX Mode 4：2-ch

Pr.02

12~23

0~255

Pr.03

24~35

Pr.04

36~47

Pr.05

48~59

Pr.06

60~71

Pr.07

72~83

Pr.08

84~95

Pr.09

96~107

Pr.10

108~119

Pr.11

120~131

Pr.12

132~143

Pr.13

144~155

Pr.14

156~167

Pr.15

168~179

Pr.16

180~191

Pr.17

192~203

Pr.18

204~215

Pr.19

216~227

Pr.20

228~239

Sound

240~255

CH1

CH2

CH3

CH4

CH5

CH6

CH7

R G B

Strobe

Dimmer

Program

Speed

0~255

0~255

0~255

0~255

0~255

CH1-3 0

Pr.01

1~11

0-27(OFF)

28-55(R)

56-83(RG)

84-111(RG)

112-139(G)

140-167(GB)

168-195(B)

196-223(RB)

224-251(RB)

252-255(RGB)

Pr.02

12~23

0~255

Pr.03

24~35

Pr.04

36~47

Pr.05

48~59

Pr.06

60~71

Pr.07

72~83

Pr.08

84~95

Pr.09

96~107

Pr.10

108~119

DMX Mode 5：7-ch

Pr.11

120~131

Pr.12

132~143

Pr.13

144~155

Pr.14

156~167

Pr.15

168~179

Pr.16

180~191

Pr.17

192~203

Pr.18

204~215

Pr.19

216~227

Pr.20

228~239

Sound

240~255

5. Colr Mode

This mode is dimming mode, press SETUP to dim the static color, press UP and DOWN buttons could set
r.000~r.255, g.000~255, b.000~b.255.

6. Sound-active Mode

1) Press the “MODE”, enter into sound-active mode “Sound Mode ”.

2) Press “SETUP” button enter to set the sound sensitivity. Press the “UP” or “DOWN”, to set the sound-active

sensitivity value “00-31”.

7. Power Charge Mode

This mode is available when battery is charging.
Press the “SETUP” button to see the power percentage 0~100.

C. Lithium Battery Instruction

1. The battery is 11.1V, 6.6Ah which is brand of 18650 Lithium Battery. It will take 3.5 hours to be fully charged
and it can be use for 6 hours. Please operate this product in the right way and discharge it. Please don’t let the
fixture spare for long time, should use and charge time by time.

2. The battery capacity display will show the product is on, fully charge or low battery. While you are using it and
charging it, the fixture will be turned off and it is fully charge. The five LED instruct lights respect the battery is
100%~80%, 60%, 40%, 20%, 20%~0%. Please charge the fixture timely when the red LED instruct light flash
because it means the battery is less than 20%.

3. Please don’ t let the fixture spare for a l long time. This fixture should be charged every three or six months at
least one time.

4. Do not use this fixture in high temperature for long time, or the lithium battery would be fire, lose function or
reduce life

D. IR Specification
Warmth warning: when you use the IR to, you need to keep the IR aiming at the light for flexible control.
However, the IR will be useless when the mode turns to “DMX mode” and Master/Slave Mode”.

1. ON/OFF

2. AUTO
Press “AUTO” button and the fixture will enter into Auto Running Mode.

3. PRG

Press “PRG” button and the fixture will enter in Built-in Programs.
Press “+” or “-”button to select built in programs segment ~ .

4. SPEED

0 1 2 3 4 5 6 7 8

9

Cyan

Purple

Purlish
Red

Orange

White

Bright
Pink

Light
Green

Water
Blue

Yellow

Warm
White

Under Built-in Program Mode, press “SPEED” button enter into the speed setting mode.
You can set the programs segment running speed by press the“+” or“-”button.

5. STROBE
You will turn off the strobe function when the fixture is under built-in program mode by press “STROBE”.
Oppositely, you will turn on the strobe function. You can set the strobe value by press “+” or “-” button, the strobe

value is ~ .

6. Dimming Mode
a. Press “DIMMING” button and the fixture will enter into Dimming Mode.
b. Press “R”, “G”, “B” buttons respectively and the fixture will enter into single color value setting mode. In

order to get great color effect, please press “+” or “-”button to adjust corresponding single color value

“000~255”. (“A”, “W” button are invalid)
The fixture will enter into static color mode no matter which status it is under if only you press number buttons.
Every number button is respect a static color, please see below table.

When it is not in Dimming Mode, "R", "G", "B", "A", "W" are static color for RED, GREEN, BLUE, AMBER,
WHITE.
IR will help to restore factory settings by press buttons of “BLACKOUT”+“9”+“8”+“7”.

NOTE:

1. Press the “MODE” and “SETUP” at same time for a few seconds to restore factory settings, the data will be
initialized.

2. Please operate the fixture base on the specification to avoid security incidents,

3. If ambient temperature is beyond the permitted range when you operate the fixture, such as, the temperature is
too high, the fixture will be damaged. Please reduce the using time of it.

4. Please do not operate the fixture with power on for safety.

5. Take out the batteries if you don't use the lamp for a long time. Replace batteries immediately if battery is dead.

6. In DMX mode, if there is a control signal, the display board will flicker for prompting.

ООО «ИНВАСК»

Адрес: 143406, Московская область, Красногорск, ул. Ленина, дом 3-Б

Тел. [phone] (многоканальный)

Факс [phone], доб. 105

http://www.invask.ru e-mail: [e-mail]

Сервис-центр «ИНВАСК»

Адрес: 143400, Московская область, Красногорск, Коммунальный квартал,

дом. 20

Тел. [phone]

e-mail: [e-mail]