Inverto IDLV-4100PM-ST, IDLV-4100PM-CT, IDLV-4100PM-DT, IDLV-4100PM-S2T, IDLV-4100PM-TT User Manual
Professional DVB Processor and Trans-Modulator
IDLV-4100PM
Professional DVB
Processor and
Trans-Modulator
User Manual
En
IDLV-4100PM
En
5
Table of Contents
6
7
7
8
9
9
9
9
9
9
9
10
10
10
10
10
11
11
12
12
14
15
16
16
17
18
19
20
Notices
Before using the device
1. General
2. Features
3. Installation
3.1 Unpacking
3.2 Operating voltage
3.3 Power-on the device
3.4 Power supply
3.5 The fuses
3.6 Connecting the device
4. Control panel and interfaces
4.1 Front panel diagram
4.2 LED indicators
4.3 LCD dispaly
4.4 Operating buttons
4.5 Common interface
4.6 Rear panel & device connnection
5. Menu Structure and Operation
5.1 IDLV-4100PM-XT series
5.2 IDLV-4100PM-XC series
5.3 Menu operation
5.4 Inputs menu
5.5 Outputs menu
5.6 System menu
6.Technical specications
7. Accessories
8. Safety
6
Notices
COPYRIGHT (Copyright © 2010 Inverto Digital Labs )
Not to be copied, used or translated in part or whole without Inverto prior consent in writing except approval of
ownership of copyright and copyright law.
WARRANTY
This warranty does not cover parts which may become defective due to misuse of the information contained in
this manual.
Read this manual carefully and make sure you understand the instructions provided. For your safety, be aware of
the following precautions.
WARNING! IMPORTANT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.
•
To avoid explosion danger, do not dispose of batteries in an open re.•
CE MARK FOR EUROPEAN HARMONISED STANDARDS
The CE mark which is attached to these products means it conforms to EMC Directive (89/336/EEC) and Low
Voltage Directive (73/23/EEC).
IMPORTANT INFORMATION
Should you experience a problem with this unit, please refer to the trouble shooting section of this user
•
manual.
Please retain the original packaging, should it be necessary at some stage to return the unit.
•
Disposal of Old Electrical and Electronic Equipment (Applicable in the European Union and other European
countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise be caused by inappropriate waste handling of this
product. The recycling of materials will help to conserve natural resources. For more detailed information about
recycling of this product, please contact your local Civic Ofce, your household waste disposal service, or the shop
where you purchased the product.
COPYRIGHTS
Television programmes, movies, video tapes, discs, and other materials may be copyrighted. Unauthorized
recording of copyrighted material may be against the copyright laws in your region. Also, use of this product with
cable television transmissions may require authorization from the cable television operator or transmitter/owner.
The supplied AC power cable must be used to power this product. If the power cord becomes
•
damaged,
VENTILATION
Do not expose the product to high temperatures, such as placing it on top of other product that produce
•
heat or in places exposed to direct sunlight or spot lights.
The ventilation slots on top of the product must be left uncovered to allow proper airow into the unit.
•
Do not stand the product on soft furnishings or carpets. Do not stack electronic equipments on top of
the product.
Do not place the product in a location subject to extreme changes in temperature. The temperature
•
gradient should be less than 10 degrees C/hour.
Place the product in a location with adequate ventilation to prevent the build-up of heat inside the
•
product. The minimum ventilation space around the unit should be 7 cm. The ventilation should not
be impeded by covering the ventilation openings with items, such as newspapers, table cloth, curtains,
etc.
POWER SOURCES
The product is not disconnected from the AC power source (mains) as long as it is connected to the
•
power outlet or wall socket, even if the product is turned off.
If the product will not be used for a long period of time, disconnect it from the AC power outlet or wall
•
socket.
En
7
Before Using the Device
Thank you for purchasing the IDLV-4100PM series.
This User Manual is written for operators/users of the IDLV-4100PM Professional Digital TV Processor and
Trans-modulator to assist in installation and operation. Please read this user manual carefully before you
proceed to install and use the device
FOR YOUR SAFE T Y
This equipment is provided with a protective earthing ground incorporated in the power cord. The main plug shall
only be inserted in a socket outlet provided with a protective earth contact. Any interruption of the protective
conductor, inside or outside the device, is likely to make the device dangerous.
Do not remove the covers of this equipment. Hazardous voltages are present within this equipment and may be
exposed if the covers are removed. Only Inverto trained and approved service engineers are permitted to service
this equipment.
No operator serviceable parts inside. Refer servicing to Inverto trained and approved service engineers.
For the correct and safe use of the device, it is essential that both operating and servicing personnel follow
generally accepted safety procedures in addition to the safety precautions specied in this manual.
Whenever it is likely that safety protection is impaired, the device must be made in-operative and secured
against unintended operation. The appropriate servicing authority must be informed. For example, safety is likely
to be impaired if the device fails to perform the intended measurements or shows visible damage.
WARNINGS
The mounting environment should be relatively dust free, free of excessive vibration and the
•
ambient temperature between 0C° to 40C°. Relative humidity of 20% to 80% (non-condensed) is
recommended.
Avoid direct contact with water.•
Never place the equipment in direct sunlight.•
The outside of the equipment may be cleaned using a lightly dampened cloth. Do not use any cleaning •
liquids containing alcohol, methylated spirit or ammonia etc.
For continued protection against re hazard, replace line fused only with same type.•
Air intake for cooling is achieved via holes at the side of the device and the fans inside. The air ow •
should not be obstructed. Therefore, the device has to be placed on a at surface, leaving some space
at the sides of the device.
When in operation, the internal temperature should not exceed the limit of 70C
• °.
Loading...