inveo Nano OUT User Manual

User manual

Nano OUT

Soft >= v1.xx

INVEO s.c.

ul. Rzemieślnicza 21

43-340 Kozy

tel: +48 33 444 65 87

www.inveo.com.pl info@inveo.com.pl

Dear Customer!

Thank you very much for choosing our product. Please carefully read this user manual as it contains most appropriate ways of dealing with this device, taking into account the basic principles of safety and maintenance. Please also keep the user guide that you can use it during subsequent use.

Manufacturer Liability!

The manufacturer is not liable for any damage caused by improper or incompatible use of this device, as well for any faults to the device resulting from improper use.

User manual NANO OUT Page 2 of 24

Contents:

1 PRELIMINARY INFORMATION....................................................................................................................4

2 DEVICE DESCRIPTION ...................................................................................................................................5

3 WARRANTY AND LIABILITY OF THE MANUFACTURER ...................................................................5

4 SAFETY GUIDELINES .....................................................................................................................................6

4.1 POWER SUPPLY....................................................................................................................................................6

4.2 STORAGE, WORKING ENVIRONMENT AND TRANSPORTATION..........................................................................................6

4.3 INSTALLATION AND USE OF THE MODULE..................................................................................................................6

4.4 UTILISATION OF THE MODULE.................................................................................................................................6

5 MODULE DESCRIPTION.................................................................................................................................7

5.1 GENERAL FEATURES.............................................................................................................................................7

5.2 TECHNICAL SPECIFICATION:....................................................................................................................................7

5.3 MODULE INPUT/OUTPUT TERMINAL DESCRIPTION.....................................................................................................8

6 MODULE CONFIGURATION..........................................................................................................................9

6.1 CHANGING THE PC SETTING FOR MODULE CONFIGURATION.........................................................................................9

6.2 CONFIGURATION OF THE MODULE MODULE THROUGH WEB BROWSER...........................................................................10

6.3 CHANGING THE STATE OF THE OUTPUT...................................................................................................................11

6.4 ACCESS CONFIGURATION.....................................................................................................................................14

6.5 MANAGING THE MODULE USING WINDOWS COMMAND LINE SOFTWARE........................................................................15

6.6 MANAGING THE MODULE USING LINUX COMMAND LINE SOFTWARE............................................................................16

6.7 MANAGING THE MODULE USING MODBUS TCP.................................................................................................17

6.8 COMMUNICATION WITH MODULE USING HTTP.......................................................................................................18

6.9 COMMUNICATION PROTOCOL DESCRIPTION..............................................................................................................20

6.10 COMMUNICATION WITH MODULE FROM OUTSIDE NETWORK .....................................................................................21

7 DHCP...................................................................................................................................................................22

8 RESTORING FACTORY DEFAULTS ..........................................................................................................22

9 FIRMWARE UPDATE.....................................................................................................................................23

NOTES..................................................................................................................................................................24

User manual NANO OUT Page 3 of 24

1 Preliminary information

Before using the module please read the user manual carefully and follow the

instructions contained within!

Description of visual symbols used in this user manual:

This symbol is responsible for reviewing the appropriate place in the user instructions, warnings and important information. Failure to follow warnings could cause injury or damage to the module.

 Important information and guidelines.

 Following this guidelines makes the use of the module easier.

Attention: The appearance of the screen shots shown in this manual may differ slightly from the actual work with the module. The differences may relate to the size and font type and size of symbols. There are no differences in the content of the information.

User manual NANO OUT Page 4 of 24

2 Device description

The NANO OUT device is used to control one electrical circuit using relay. The relay can be controlled using www website, network protocols or software supplied by manufacturer.

3 Warranty and liability of the manufacturer

The manufacturer provides a 2-year warranty on the module. The manufacturer also provides post-warranty service for 10 years from the date of the introducing the module on the market. The warranty covers all defects in material and workmanship.

The manufacturer undertakes to comply with the contract of guarantee, if the following conditions are met:

 All repairs, alterations, extensions and device calibrations are performed by the

manufacturer or authorized service,

 supply network installation meets applicable standards in this regard,  device is operated in accordance with the recommendations outlined in this manual,  device is used as intended.

The manufacturer assumes no responsibility for consequences resulting from improper installation, improper use of the module, not following this manual and the repairs of the module by individuals without permission.

This device doesn’t contain serviceable parts. The repairs can be done only by manufacturers approved repair service.

User manual NANO OUT Page 5 of 24

4 Safety guidelines

The module has been constructed using modern electronic components, according to the latest trends in the global electronics. In particular, much emphasis was placed on ensuring optimum safety and reliability of control. The device has a housing with high quality plastic.

4.1 Power supply

The module power supply must be in range of 10-24V AC or DC. The power to module is delivered via POE adapter (Power Over Ethernet).

4.2 Storage, working environment and transportation

The module has to be used in closed environments free from fumes and corrosive atmosphere.

Environmental conditions for storage:

 Temperature: + 5°C to +45°C,

 Relative humidity: <75%,  Atmospheric pressure: 700 – 1060hPa.

Environmental conditions for use:

 Temperature: +10°C to +30°C,

 Relative humidity: 30% to 75%,  Atmospheric pressure: 700 to 1060hPa.

Recommended conditions for transportation:

 Temperature: -10°C to +45°C,

 Relative humidity: 20 to 95%,  Atmospheric pressure 700 to 1060hPa.

4.3 Installation and use of the module

The module should be used following the guidelines shown in next part of the user manual.

4.4 Utilisation of the module

When it becomes necessary to liquidate the device (e.g., after the time of use), please contact the manufacturer or its representative, who are obliged to respond appropriately, i.e., collecting the module from the user. You can also ask the companies involved in utilization and / or liquidation of electrical or computer equipment. Under no circumstances should you place the device along with other garbage.

User manual NANO OUT Page 6 of 24

5 Module description

5.1 General features

Overall view of the module is shown on the picture below.

There are several ways to communicate with the module:

• using built in WWW server via any web browser,

• MODBUS TCP protocol,

• SNMP protocol,

• HTTP protocol,

• User application – communication protocol available for user

NANO module is equipped with two LEDs indicators: power and output status.

5.2 Technical specification:

Power supply voltage: 10-24VDC (POE) Power consumption: 1.5 W

Output

Max voltage: 250V AC, 30V DC,

Max current: 5A,

NO (normal open),

Engage time: 10ms,

Disengage time: 5ms,

LAN: Ethernet 1x10Mbps, RJ45

User manual NANO OUT Page 7 of 24

Nano Out

5.3 Module input/output terminal description

Module NANO OUT has two connection terminals:

• RJ45 socket – LAN network and POE

• Screw terminal – input

Teminal No Name Description

1 Relay output 2 RESET Reset to factory defaults:

IP:192.168.111.15 username: admin password: admin00

3 LAN LAN network connections

Pins: 1,2,3,6 -data 4,5,7,8 - power

User manual NANO OUT Page 8 of 24

6 Module configuration

If using the module for the first time it is needed to configure it as shown below

6.1 Changing the PC setting for module configuration.

After connecting the module to the network there is a need to change the PC setting. In order to do that navigate to: Start->Control Panel->Network connections. Then right click on the current network connection and click „Properties”. The configuration screen as shown below should be visible on the screen:

Choose the „Internet Protocol (TCP/IP)” and press „Properties”:

Tick the box „Use the following IP address” and enter: IP address: 192.168.111.1 Subnet mask: 255.255.255.0 The rest of the setting can be left blank. Press OK to accept the changes.

User manual NANO OUT Page 9 of 24

TCP/IP example settings

6.2 Configuration of the module module through web browser

Start the web browser and enter the following address into address bar:

192.168.111.15.

The default user name is „admin” with password „admin00”

There are several fields used to configure the module network settings:

 MAC Address – MAC address of the module,  Host Name – NETBIOS host name of the module,  Enable DHCP – When this box is ticked the module will get its address from DHCP

server,

 IP Address – IP address of the module – when configured manually,  Gateway – Network gateway,  Subnet Mask – Subnet mask of the module,  Primary DNS, Secondary DNS – DNS servers addresses,  Destination IP – Network address of the server that the module will connect to -

optional,

 Destination Port – Network port of the server that the module can connect to.

User manual NANO OUT Page 10 of 24

After changing the configuration press the „Save Config” button.

6.3 Changing the state of the output.

Visualisation of output state is shown below.

Output

To change state of the output press Output On/Off button. Relay State shows current state of output relay.

Relay configuration can be change in Channel tab

Description of output relay settings:

User manual NANO OUT Page 11 of 24

Output control

Static monostable.

Toggle bistable

1-Pulse 1 time pulse

Time On On time in Toggle lub 1-Pulse modes

Time Off Off time in Toggle mode

Start:Off Disables relay after power reset

Start:On Enables relay after power reset

Start:Last Relay set to the same state as before

power reset

Dest. Off Disables sending output state to different

devices

Dest. 1 Sends state of output 1 to different devices

Dest. 2 Sends state of output 2 to different devices

... ...

Dest. 8 Sends state of output 8 to different devices

User manual NANO OUT Page 12 of 24

User manual NANO OUT Page 13 of 24

6.4 Access configuration

Web site used to configure the access to the module is shown below. These settings allow for changing the access password and to enable/disable particular services.

Menu Administration umożliwia skonfigurowanie przez Użytkownika jakie usługi mają być aktywne w urządzeniu oraz zmianę hasła dostępu.

Changing the password

Enter old password into Current Password field. Enter new password into New Password field and into Re-type Password field then press „Save Config” to save new passwords.

Enabling/disabling particular service

This function enables/disables different services. By enabling the tick box next to a service user can turn it on or off.

Module Access configuration

 Enable user password – enables/disables requirement for user password

User manual NANO OUT Page 14 of 24

Ustawienia zabezpieczeń

 Enable admin password – enables/disables requirement for admin password  Enable Program Access – enables/disables the connection to the module via PC

software – Windows or Linux OS.

 Enable MODBUS TCP Protocol – enables/disables access using MODBUS TCP protocol.  Enable SNMP – enables/disables access using SNMP protocol.  Enable Destination client – enables/disables access using mode of operation

„customer”.

 Enable TFTP bootloader – enables/disables 10 second bootloader mode after module

reboot

6.5 Managing the module using windows command line software

The module can be operated using windows command line software – the software is delivered with the module.

Syntax is as follows:

: TCPRel.exe [Parameters]

Parameter Description

-out=1 Output number, for NANO always 1

-host=[HOST] Module IP address

-port=[PORT] Module Port number

-on | -off Enables or disables output

-verb Enabled display of additional info

-stat Displays current state of output

Examples:

Enables relay - module address 192.168.111.15 listening on port 9761:

TCPRel -out=1 -host=192.168.111.15 -port=9761 -on

Read output state:

TCPRel -host=192.168.111.15 -port=9761 –in=1 -stat

User manual NANO OUT Page 15 of 24

6.6 Managing the module using Linux command line software

The module can be configured using Linux command line software – the software is delivered with the module. Syntax is as follows:

./TcpRel.exe [Parameters]

Parameter Description

-o 1

Output number, for NANO always 1

-h [HOST]

Module IP address

-p [PORT]

Module Port number

-s [0,1]

Enables or disables output

-l

Displays current state of output

Examples:

Enables relay - module address 192.168.111.15 listening on port 9761:

./tcprel -o 1 -h 192.168.111.15 -p 9761 -s 1

Read output state::

./tcprel -h 192.168.111.15 -p 9761 –o 1 -l

User manual NANO OUT Page 16 of 24

6.7 Managing the module using MODBUS TCP

MODBUS TCP protocol is listening on port 502. The module supports following functions of MODBUS protocol:

- 0x01 Read Coils,

- 0x05 Write Single Coil,

The registers description is shown in tables below

MODBUS TCP - Coils

Register Name Mode:

R-read

W-write

Description

1000 On1 R/W Enable relay

MODBUS TCP - Holding Registers

Registe

r

Name Mode:

R-read

W-write

Description

4000 T1On R/W Relay engage time (*100ms) 4001 T1Off R/W Relay disengage time (*100ms) 4002 Rel1Mode R/W Mode of operation:

1 – Static 2 – Toggle 3 – 1-Pulse

User manual NANO OUT Page 17 of 24

6.8 Communication with module using HTTP.

NANO OUT modules can be controlled using HTTP. To read current state of the module inputs/outputs access this address - http://192.168.111.15/stat.php – in web browser.

XML file consist all of the information:

Section Description

<prod_name>PE-1-0</prod_name>

Type of module In this case PE-1-0.

Output state (enabled/disabled). In this case output inactive

Output state

In NANO-OUT always read as 0

In NANO-OUT always read as 0

In NANO-OUT always read as 0

Command Description

http://nr_ip/stat.php?on=1

Enable output relay.

http://nr_ip/stat.php?off=1

Disable output relay.

http://nr_ip/stat.php?inv=1

Invert output state.

http://nr_ip/stat.php?set=0000000x

Set output. Options x=: 1-Enable 0-Disable n-Invert

Example:

1.Enable relay output:

http://192.168.111.15/stat.php?o n =1

2.Invert output relay state :

http://192.168.111.15/stat.php? inv=1

3.Disable relay output:

http://192.168.111.15/stat.php?off=1

User manual NANO OUT Page 18 of 24

User manual NANO OUT Page 19 of 24

6.9 Communication protocol description

Byte 1 2 3 4 5 6 7 8 9 10 11

Name SOF CMD CH Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 CRC

Return

Command

Set output

15 1 0-7 Mode

[1-3]*

ON/OFF [0,1]

TON LSB*

TON MSB*

TOFF LSB*

TOFF MSB*

Restart state**

CRC ON or NO

Read channel parameters

15 2 0-7 x x x x x x x CRC

Set counter

15 10 0-7 [0:7] [8:15] [16:23] [24:31] CRC

Read counter

15 11 0-7 [0:7] [8:15] [16:23] [24:31] CRC

WWW control

15 99 x 1

-status 0x55 –

off

all

other -

on

x x x x x x CRC ON or NO

Read channels

15 100 x x x x x x x x CRC CH7-CH0 Chx – 2

bytes; 1 output state 2 coil state

Read channel name

15 101 0-7 x x x x x x x CRC String

Read device name

15 200 x x x x x x x x CRC String

*only Lantick and PE-2-1 ** only Lantick *** - Reading parameters returns:

SOF CMD Ch Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 CRC

15 2 0-7 Mode[1-3],

100-input

ON/OFF[0,1] TON

LSB

TON MSB

TOFF

LSB

TOFF

MSB

Restart state CRC

Description Value State

ON/OFF 0 off

1 on

MODE 1 static

2 toggle

3 1-pulse

CRC Byte sum

As default modules are listening on port 9761

Frame examples:

Enabling output 1 in static mode

SOF CMD CH Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 CRC

15 1 0 0 1 1 0 0 0 0 18

Set counter 2 to 100

SOF CMD CH Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 CRC

15 10 1 100 0 0 0 0 0 0 132

Moduł standardowo nasłuchuje na porcie TCP 9761.

Przykładowe ramki:

Załączenie wyjścia #1 w trybie static

SOF CMD CH D1 D2 D3 D4 D5 D6 D7 CRC

15 1 0 1 1 0 0 0 0 0 18

6.10 Communication with module from outside network

If the module is in the LAN network different than PC that connects to it, the redirection of ports is necessary. Depending on the form of communication different ports need to be redirected:

Using web interface:  port TCP/IP 80

Computer software or customer application:

1 port TCP/IP 9761

Using MODBUS TCP protocol:

• port TCP/IP 502

Using SNMP protocol:

• port UDP 161

7 DHCP

To enable disable DHCP:

1. Press and hold RESET button for 5-10 seconds

2. Green LED will start flashing 2 times a second

3. Release RESET button

8 Restoring factory defaults

In order to restore the module to its factory defaults press and hold reset button for at least 10-15 seconds. The green LED will start flashing 4 times second With factory defaults restored the module settings are as follows:

− IP address : 192.168.111.15

− IP mask : 255.255.255.0

− User name : admin

− Password: admin00

9 Firmware update

The module has the ability to update the firmware. The firmware is supplied as a file with .hex extension.

Note! Improper use of the update feature may damage the module. Make sure that undisturbed power is connected to the module for duration of programming.

To perform the programming operation, go to the Windows command line (Start-> Run> type 'cmd' and confirm with Enter).

Then navigate to the directory where the file resides and enter the command

tftp <module_ip_adress> PUT filename.hex

where: < module_ip_adress > is the IP address of the module filename.hex – is the firmware supplied by Inveo s.c.

The programming takes about 1 minute and it’s confirmed by “File Transferred” message.

Notes

…………………………………………………………………………………………………………………………………………………………

inveo Nano OUT User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1 Preliminary information

2 Device description

3 Warranty and liability of the manufacturer

4 Safety guidelines

4.1 Power supply

4.2 Storage, working environment and transportation

4.3 Installation and use of the module

4.4 Utilisation of the module

5 Module description

5.1 General features

5.2 Technical specification:

5.3 Module input/output terminal description

6 Module configuration

6.1 Changing the PC setting for module configuration.

6.2 Configuration of the module module through web browser

6.3 Changing the state of the output.

6.4 Access configuration

6.5 Managing the module using windows command line software

6.6 Managing the module using Linux command line software

6.7 Managing the module using MODBUS TCP

6.8 Communication with module using HTTP.

6.9 Communication protocol description

6.10 Communication with module from outside network

7 DHCP

8 Restoring factory defaults

9 Firmware update