INVENTOR V2MCI-30, U2MRS-30, V2MCI-36, U2MRS-24, U2MRS-36 Owner's Manual
...
Models: V2MCI-24 / U2MRS-24
V2MCI-30 / U2MRS-30
V2MCI-36 / U2MRS-36
V2MCI-50 / U2MRT-50
V2MCI-60 / U2MRT-60
IMCI-36 / UMLT-36
IMCI-50 / UMLT-50
IMCI-60 / UMLT-60
Remote Controller of Cassette Unit
11
2
3
4
6
7
7
7
8
8
9
12
Handling the remote controller ......................................................
Remote controller Specifications...................................................
Function buttons .................. .........................................................
Indicators on LCD ..........................................................................
How to use the buttons .................................................................
Auto operation.................................................................................
Cooling/Heating/Fan operation......................................................
Dehumidifying operation ...............................................................
Swing operation..............................................................................
Timer operation...............................................................................
ECO operation ..............................................................................
CONTENTS
Use the remote controller within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
Location of the remote controller.
8m
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller, either move
these appliances or consult your local dealer.
The remote controller is powed by two dry
batteries(R03/LR03X2) housed in the rear
part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new
batteries,placing the(+) and (-) ends correctly.
(3) Reattach the cover by sliding it back into
position.
NOTE: When the batteries are removed, the
remote controller erases all programming.
After inserting new batteries, the remote
controller must be reprogrammed.
Replacing batteries
.
Handling the remote controller
22
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
LOW
MODE
FAN SPEED
SWING
TIMER ON
ON/OFF
TIMER
OFF
RESET
LOCK
SET T
EMPE
RATU
RE( C)
Model
Lowest Voltage of
CPU Emitting Signal
Rated Voltage
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Dry batteries R03/LR03 2)
2.0V
Remote Controller Specifications
1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling & heating models only)
and FAN.
2. Timer Setting Function in 24 hours.
OO
3. Indoor Setting Temperature range: 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
Environment
Signal Receiving
Range
Performance Feature
Function buttons
CAUTIONS
Do not mix old and new batteries or batteries of a different type.
Do not leave the batteries in the remote controller if it is not going
to be used for 2 or 3 months.
Dispose of the old batteries in the special containers to be found
in the sales outlets.
1
TEMP UP Button
Push this button to increase the indoor temperature setting in 1 C increments to 30 C.
2
TEMP DOWN Button
Push this button to decrease the indoor temperature setting in 1 C increments to 17 C.
Each time the button is pressed, the operation
mode is selected in the sequence of the following:
3
MODE Button
33 44
4
SWING Button
SWING Button
6
5
7
RESET Button
Once the recessed RESET button is pressed,
all of the current settings will be cancelled
and the controller will return to the initial settings.
8
ON/OFF Button
Operation starts when this button is pressed
and stops when the button is pressed again.
NOTE: Heat mode is for Cooling & Heating
models only.
AUTO
COOL
DRY
HEAT FAN
Used to select the fan speed in four steps:
Auto Low Med High
FAN SPEED Button
O O
-5 C~60 C
RG51C/(C)E, RG51C/BG(C)E.
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
AIR
DIRECTION
FAN SPEED
SWING
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET LOCK
4
SET TEMPERATURE( C)
Used to stop or start horizontal louver movement.The louver will swing up and down
automatically if push this button.
Used to stop or start vertical louver movement .
Buttons design might be slightly different from the actual one you purchased
depending on individual models.
All the functions described are accomplished by the indoor unit. If the indoor unit
has no this feature, there is no corresponding operation happened when press the
relative button on the remote controller.
Note:
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
AIR
DIRECTION
FAN SPEED
SWING
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
AIR DIRECTION Button
Used to set the desired up/down air flow
direction. The louver changes 6 degree in
angle for each press.
4
NOTE:This button only available when the
remote controller is used with corresponding
unit.
Loading...