INVENTOR RG35C/BGCE, RG35A2/BGCE, RG35A14/BGCEF, RG35B/BGCE, RG35A1/BGEF Owner's Manual

Wall Mounted Unit

Σας ευχαριστούμε που επιλέξατε τη
μονάδα κλιματισμού της INVENTOR. Για
τη σωστή χρήση της μονάδας.
παρακαλούμε διαβάστε προσεκτικά το
παρόν εγχειρίδιο και φυλάξτε το για
αναφορά στο μέλλον.

Thank you for choosing INVENTOR air
conditioning system. For correct use of
this unit, please read this manual
carefully and keep it for future
reference.

Μοντέλα:

English/Ελληνικά/ Română

Ασύρματο Τηλεχειριστήριο

Επιτοίχιας Κλιματιστικής Μονάδας

Εγχειρίδιο Χρήσης

Owner’s Manual

A3MVI-10/A3MVO-10
A3MVI-13/A3MVO-13
A2MVI-18/A2MVO-18
A2MVI-24/A2MVO-24
P4MVI-09/P4MVO-09
P4MVI-12/P4MVO-12
P4MVI-18/P4MVO-18
P4MVI-24/P4MVO-24
A3MVI-10WFR/A3MVO-10
A3MVI-13WFR/A3MVO-13
A2MVI-18WFR/A2MVO-18
A2MVI-24WFR/A2MVO-24
P4MVI-09WFR/P4MVO-09
P4MVI-12WFR/P4MVO-12
P4MVI-18WFR/P4MVO-18
P4MVI-24WFR/P4MVO-24

11

CONTENTS

Use the remote controller within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.

Location of the remote controller.

8m

The remote controller is powed by two dry batteries(R03/LR03X2) housed in the
rear part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new batteries,placing the(+) and (-)
ends correctly.
(3) Reattach the cover by sliding it back into position.

NOTE: When the batteries are removed, the remote controller erases all progra­mming. After inserting new batteries, the remote controller must be reprogrammed.

Replacing batteries

Handling the remote controller

CAUTIONS

The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller. either move
these appliances or consult your local dealer.

22

CAUTIONS

Do not mix old and new batteries or batteries of different types.
Do not leave the batteries in the remote controller if they are not
going to be used for 2 or 3 months.
Do not dispose batteries as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.

2

3

5

8

9

9

9

10

10

11

14

15

15

Handling the remote controller ......................................................

Remote controller Specifications...................................................

Function buttons .................. .........................................................

Indicators on LCD ..........................................................................

How to use the buttons .................................................................

Auto operation.................................................................................

Cooling/Heating/Fan operation......................................................

Dehumidifying operation ...............................................................

Adjusting air flow direction............................................................

Timer operation...............................................................................

SLEEP/FRESH function..................................................................

LED/FOLLOW ME function ...........................................................

TRUBO/SELF CLEAN function ......................................................

NOTE: Replace the batteries when there is no receiving beep from the indoor

unit or if the transmission indicator on the remote controller fails to light.

Model

Rated Voltage

8m

3.0V(Dry batteries R03/LR03 2)

Remote Controller Specifications

1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only model without), and FAN.

2. Timer Setting Function in 24 hours.

3. Indoor Setting Temperature Range : 17 C~30 C.

4. Full function of LCD (Liquid Crystal Display).

Environment

Signal Receiving
Range

Performance Feature

33 44

RG35A(2)/BG(C)EF,RG35A1(4)/BG(C)EF,RG35B/BG(C)E,RG35C/BG(C)E, RG36B3/BGE

RG36A(1)/BG(C)EF

RG36A2/BG(C)EF RG36C/BG(C)E

RG35A4/BG(C)EF

RG35A(2)/BG(C)EF

RG35B/BG(C)E

RG35C/BG(C)E

RG36A(1)/BG(C)EF,RG36A2/BG(C)EF,RG36B(1)/BG(C)E,RG36C/BG(C)E

-5 C 60 C

~~

TURBO
SELF
CLEAN

TURBO

SLEEP
FRESH

SLEEP

SLEEP

SHORT
CUT

SHORT
CUT

SHORT
CUT

TIMER
ON

TIMER
ON

TIMER
ON

TIMER
OFF

TIMER
OFF

TIMER
OFF

LOCK

LOCK

LOCK

RESET

RESET

RESET

LED
FOLLOW
ME

LED

FAN
SPEED

FAN
SPEED

FAN
SPEED

DIRECT

DIRECT

DIRECT

SWING

SWING

SWING

MODE

MODE

O

M

R

E

Y

M

MODE

TEMP

TEMP

TEMP

MODE

MODE

MODE

MODE

SWING

SWING

SWING

SWING

TEMP

TEMP

TEMP

TEMP

SHORTCUT

SHORTCUT

SHORTCUT

SHORTCUT

FAN
SPEED

FAN
SPEED

FAN
SPEED

FAN
SPEED

TIMER
OFF

TIMER
OFF

TIMER
OFF

TIMER
OFF

RESET

RESET

RESET

RESET

LOCK

LOCK

LOCK

LOCK

LED
FOLLOW ME

LED
FOLLOW ME

LED

TIMER
ON

TIMER
ON

TIMER
ON

TIMER
ON

TURBO
SELF CLEAN

TURBO
FP

TURBO

DIRECT

DIRECT

DIRECT

DIRECT

SLEEP
FRESH

SLEEP

SLEEP

SLEEP

NOTE: There is only slight difference on the appearance between RG35
series and RG 36 series. The operations and functions of the buttons are
the same. Some buttons have two functions, some buttons have only one
function, for example: and . Please refer to the above

illustrations for details.

SLEEP
FRESH

SLEEP

RG35A1/BGEF

SLEEP

SHORT
CUT

TIMER
ON

TIMER
OFF

LOCK

RESET

LED

FAN
SPEED

DIRECT

SWING

MODE

TEMP

RG36B(1)/BG(C)E
RG36B3/BGE

TURBO
FP

ON/OFF

ON/OFF

ON/OFF

ON/OFF

Modles of RG36B(3)/BG(C)E do
not have FP function.

F

E

O

M

L

L

W

O

55 66

Function buttons

1

2

Each time the button is pressed, the operation
mode is selected in a sequence of following:

3

MODE Button

1

1

2

2

4

4

5

5

3

3

8

8

10

10

9

9

4

5

ON/OFF Button( )
Operation starts when this button is pressed
and stops when this button is pressed again.

NOTE: Heat mode is for Cooling & Heating models only.

AUTO

COOL

DRY

HEAT FAN

6

6

7

7

11

11

12

12

13

13

14

14

SHORTCUT(MEMORY SHORTCUT) Button

NOTE: While the unit is running under SLEEP

mode, it would be cancelled if press the MODE,
FAN SPEED or ON/OFF button.

TIMER ON Button

Used to restore the current settings or
resume previous settings.
On the first time connecting to the power,
if push the SHORTCUT button, the unit

O

will operate on AUTO mode, 24 C, and fan
speed is Auto.
Push this button when remote controller is
on, the system will automatically revert back
to the previous settings including operating
mode, setting temperature, fan speed level
and sleep feature(if activated). And transmit
the signals to the unit.
If push this button when remote controller
is off, the system will only resume the
previous settings and will not transmit
the signals to the unit. And the sleep
feature is disable.
If pushing more than 2 seconds, the system
will automatically restore the current
operation settings including operating mode,
setting temperature, fan speed level and
sleep feature(if activated ).

15

15

8

6

7

MODE

MODE

SWING

SWING

TEMP

TEMP

SHORTCUT

SHORTCUT

FAN
SPEED

FAN
SPEED

TIMER
OFF

TIMER
OFF

RESET

RESET

LOCK

LOCK

LED
FOLLOW ME

LED
FOLLOW ME

TIMER
ON

TIMER
ON

TURBO
SELF CLEAN

TURBO
FP

DIRECT

DIRECT

SLEEP
FRESH

SLEEP

1

2

4

5

3

9

10

8

6

7

11

12

13

14

15

TURBO
SELF
CLEAN

SLEEP
FRESH

SHORT
CUT

TIMER
ON

TIMER
OFF

LOCK

RESET

LED
FOLLOW
ME

FAN
SPEED

DIRECT

SWING

MODE

TEMP

RG35A(2)

RG36A(1)

SWING Button

DIRECT Button

Used to stop or start horizontal louver auto
swing feature.

Used to change the louver movement and set
the desired up/down air flow direction. The

O

louver changes 6 in angle for each press.

Active/Disable SLEEP function. If pushing
more than 2 seconds, the FRESH function
will be activated, pushing more than 2
seconds again to disable.

SLEEP/FRESH Button

,

,

Active/Disable TURBO function. If pushing
more than 2 seconds, the SELF CLEAN
function will be activated, pushing more than
2 seconds again to disable(depending on
models).

TURBO/FP Button:

Active/Disable TURBO function.If pushing
more than 2 seconds during the heating
operation(only when the setting mode is
HEAT), the unit will operate at high fan
speed with the temperature automatically

O

set to 8 C.The display window of indoor unit
will display FP . For the unit without display
area, the defrost indicator light will be
keeping on for 2 seconds, and then be off for
2 secondes by turns. Press ON/OFF,SLEEP,
FP,MODE,FAN SPEED,UP, DOWN or
SHORTCUT while operating will cancel the
FP function.

TURBO/SELF CLEAN Button:

,

,

When you press the recessed RESET button,
all current settings are cancelled and the
control will return to the initial settings.

RESET Button:

Push this button to decrease setting temper­ature or to decrease Hour during Timer setting.

UP Button( )
Push this button to increase setting temper­ature or to increase Hour during Timer setting.

DOWN Button( )

9

-

+

12

10

11

Used to select the fan speed in four steps:
AUTO LOW MED HIGH

FAN SPEED Button

Press this button to initiate the auto-on time
sequence. Each press will increase the
auto-timed setting in 30 minutes increments.
When the setting time displays 10H, each
press will increase the auto-timed setting
60 minutes increments. To cancel the
auto-timed program, simply adjust the
auto-on time to 0.0.

RG35A1

1

2

4

5

3

9

10

8

6

7

11

12

13

14

15

TURBO
FP

SLEEP

SHORT
CUT

TIMER
ON

TIMER
OFF

LOCK

RESET

LED

FAN
SPEED

DIRECT

SWING

MODE

TEMP

RG36B1

,,

,,

ON/OFF

ON/OFF

ON/OFF

Function buttons(continued)

14

77 88

Indicators on LCD

15

LOCK Button

LED/FOLLOW ME Button

Disable/Active indoor screen Display. When
pushing more than 2 seconds, the FOLLOW
ME function will be activated, pushing more
than 2 seconds again to disable.

,

,

Transmission Indicator

Temp./Timer display

Fan speed display

Sleep Display

Mode display

ON/OFF display

This transmission indicator lights when remote
controller transmits signals to the indoor unit.

Displays the current operation mode. Including
auto( ), cool( ), dry( ), heat( ) (Not
applicable to cooling only models), fan( )
and back to auto( ).

OO

Displays the temperature setting(17C ~30C ). When
you set the operating mode to FAN, no temperature
setting is displayed. And if in the TIMER mode, shows
the ON and OFF settings of the TIMER.

Displayed by pressing the ON/OFF button.
Press the ON/OFF button again to remove.

Displays the selected fan speed, AUTO(no display)
and three fan speed levels " " (LOW) " " (MED)
" " (HIGH) can be indicated. The fan speed is AUTO
when the operating mode is either AUTO or DRY.

Displayed under sleeping operation.
Press the SLEEP button again to remove.

Note:

All indicators shown in the figure are for the purpose
of clear presentation. But during the actual operation
only the relative functional signs are shown on the
display window.

Lock Display

Displayed when LOCK mode is activated.

FOLLOW ME Display

Displayed when FOLLOW ME function is activated.

1

2

4

5

3

9

10

8

6

7

11

12

13

14

15

TURBO
SELF
CLEAN

SLEEP
FRESH

SHORT
CUT

TIMER
ON

TIMER
OFF

LOCK

RESET

LED
FOLLOW
ME

FAN
SPEED

DIRECT

SWING

MODE

TEMP

When you press the recessed LOCK button,
all current settings are locked in and the
remote controller does not accept any
operation except that of the LOCK. Press
again to cancel the LOCK mode.

NOTE:
Buttons design might be slightly
different from the actual one you
purchased depending on individual
models.
All the functions described above
are accomplished by the indoor unit,
if the indoor unit has no this feature,
there is no corresponding operation
happened when press the relative
button on the remote controller.

auto cool dry heat fan

sleep follow me lock run

SET TEMP. TIMER ONOFF

TIMER OFF Button

13

Press this button to initiate the auto-off time
sequence. Each press will increase the
auto-timed setting in 30 minutes increments.
When the setting time displays 10H, each
press will increase the auto-timed setting
60 minutes increments. To cancel the
auto-timed program, simply adjust the
auto-off time to 0.0

ON/OFF

How to use the buttons

99 1010

Cooling /Heating/Fan operation

Ensure the unit is plugged in and power is
available.

1. Press the MODE button to select COOL,
HEAT(cooling & heating models only) or
FAN mode.

2. Press the UP/DOWN buttons to set the
desired temperature.

3. Press the FAN button to select the fan speed
in four steps- Auto, Low, Med,or High.

4. Press the ON/OFF button to start the air
conditioner.

The temperature can

OOO

be set within a range of 17 C~ 30 C in 1 C
increments.

In the FAN mode, the setting temperature is not
displayed in the remote controller and you are not
able to control the room temperature either. In this
case, only step 1, 3 and 4 may be performed.

NOTE

Auto operation

Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
display panel of the indoor unit starts flashing.

1. Press the MODE button to select Auto.

2. Press the UP/DOWN button to set the
desired temperature. The temperature can

OOO

be set within a range of 17 C~ 30 C in 1 C
increments.

3. Press the ON/OFFbutton to start the air
conditioner.

1. In the Auto mode, the air conditioner can logically
choose the mode of Cooling, Fan, and Heating
by sensing the difference between the actual
ambient room temperature and the setting
temperature on the remote controller.

2. In the Auto mode, you can not switch the fan speed.
It has already been automatically controlled.

3. If the Auto mode is not comfortable for you , the
desired mode can be selected manually.

NOTE

3

1

2

2

4

1

2

2
3

Dehumidifying operation

Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
display panel of the indoor unit starts flashing.

1. Press the MODE button to select DRY mode.

2. Press the UP/DOWN buttons to set the
desired temperature.

3. Press the ON/OFF button to start the air
conditioner.

The temperature

OO

can be set within a range of 17 C~ 30 C

O

in 1 C increments.

In the Dehumidifying mode, you can not switch the
fan speed. It has already been automatically controlled.

NOTE

Adjusting air flow direction

Use the SWING and DIRECT button to adjust
the desired airflow direction.

1. When push the DIRECT button, the horizontal
louver changes 6 degree in angle for each
push.

2. When push the SWING button, the louver
will swing up and down automatically.

NOTE: When the louver swing or move to a
position which would affect the cooling
or heating effect of the air conditioner,
it would automatically change the
swing/moving direction.

3

1

2

2

SHORTCUT

FAN
SPEED

TIMER
OFF

LOCK

LED
FOLLOW ME

MODE

SWING

TEMP

RESET

TIMER
ON

TURBO
SELF CLEAN

DIRECT

SLEEP
FRESH

SHORTCUT

FAN
SPEED

TIMER
OFF

LOCK

LED
FOLLOW ME

MODE

SWING

TEMP

RESET

TIMER
ON

TURBO
SELF CLEAN

DIRECT

SLEEP
FRESH

SHORTCUT

FAN
SPEED

TIMER
OFF

LOCK

LED
FOLLOW ME

MODE

SWING

TEMP

RESET

TIMER
ON

TURBO
SELF CLEAN

DIRECT

SLEEP
FRESH

1111

1212

Timer operation

Press the TIMER ON button can set the auto-on
time of the unit. Press the TIMER OFF button
can set the auto-off time of the unit.

1. Press the TIMER ON button. The remote
controller shows TIMER ON, the last Auto-on
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to reset
the Auto-on time to START the operation.

2. Push the TIMER ON button again to set desired
Auto-on time. Each time you press the button,
the time increases by half an hour between 0
and 10 hours and by one hour between 10 and
24 hours.

3. After setting the TIMER ON ,there will be a one
second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.

To set the Auto-on time.

To set the Auto-off time.

1. Press the TIMER OFF button. The remote
controller shows TIMER OFF, the last Auto-off
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to reset
the Auto-off time to stop the operation.

2. Push the TIMER OFF button again to set
desired Auto-off time. Each time you press the
button, the time increases by half an hour
between 0 and 10 hours and by one hour
between 10 and 24 hours.

3. After setting the TIMER OFF ,there will be a
one second delay before the remote controller
transmits the signal to the air conditioner. Then
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.

1

2

The effective operation time set by the remote controller for the timer function
is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0,

5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15,16,17, 18, 19, 20,
21, 22, 23 and 24.

CAUTION

!

Example of timer setting

Start

Off

6 hours later

(Auto-on Operation)

The TIMER ON feature is useful when you want
the unit to turn on automatically before you return
home. The air conditioner will automatically start
operating at the set time.

To start the air conditioner in 6 hours.

1. Press the TIMER ON button, the last setting
of starting operation time and the signal "h"
will show on the display area.

2. Press the TIMER ON button to display "6:0h"
on the TIMER ON display of the remote
controller.

3. Wait for 3 seconds and the digital display
area will show the temperature again. The
"TIMER ON" indicator remains on and this
function is activated.

TIMER ON

Example:

Set

TIMER ON

SHORTCUT

FAN
SPEED

TIMER
OFF

LOCK

LED
FOLLOW ME

MODE

SWING

TEMP

RESET

TIMER
ON

TURBO
SELF CLEAN

DIRECT

SLEEP
FRESH

1313

1414

Stop

On

Set 10 hours later

(Auto-off Operation)

The TIMER OFF feature is useful when you want the
unit to turn off automatically after you go to bed. The
air conditioner will stop automatically at the set time.

To stop the air conditioner in 10 hours.

1. Press the TIMER OFF button, the last setting of
stopping operation time and the signal "h" will
show on the display area.

2. Press the TIMER OFF button to display "10h" on
the TIMER OFF display of the remote controller.

3. Wait for 3 seconds and the digital display area
will show the temperature again. The "TIMER
OFF" indicator remains on and this function is
activated.

TIMER OFF

Example:

On

Stop

2 hours later
after setting

Set

To stop the air conditioner 2 hours after setting and
start it again 10 hours after setting.

1. Press the TIMER OFF button.

2. Press the TIMER OFF button again to display

2.0h on the TIMER OFF display.

3. Press the TIMER ON button.

4. Press the TIMER ON button again to display 10h
on the TIMER ON display .

5. Wait for 3 seconds and the digital display area
will show the temperature again. The "TIMER
ON OFF" indicator remains on and this function is
activated.

TIMER OFF TIMER ON
(On Stop Start operation)
This feature is useful when you want to stop the air
conditioner after you go to bed, and start it again in
the morning when you wake up or when you return
home.

Example:

COMBINED TIMER

(Setting both ON and OFF timers simultaneously)

Start

Example:

TIMER ON TIMER OFF
(Off Start Stop operation)
This feature is useful when you want to start
the air conditioner before you wake up and
stop it after you leave the house.

To start the air conditioner 2 hours after setting,
and stop it 5 hours after setting.

1. Press the TIMER ON button.

2. Press the TIMER ON button again to display

2.0h on the TIMER ON display.

3. Press the TIMER OFF button.

4. Press the TIMER OFF button again to display

5.0h on the TIMER OFF display .

5. Wait for 3 seconds and the digital display area
will show the temperature again. The "TIMER
ON OFF" indicator remains on and this function
is activated.

Off

Stop

Start

10 hours later
after setting

2 hours later
after setting

5 hours later
after setting

Set

NOTE: The timer setting(TIMER ON or TIMER
OFF) that in sequence occurs directly after the
set time will be activated first.

SLEEP/FRESH function

TIMER OFF

TIMER ON OFF

TIMER ON OFF

1

Press this button less than 2nds will initiate
SLEEP function. And if keep pressing this
button more than 2nds,the FRESH function is
initiated.
The sleep function enables the unit to automa­tically increase(cooling) or decrease(heating)

O

1 C per hour for the first two hours, then hold
steady for the next 5 hours, after that the unit
will stop operation. It can maintain the most
comfortable temperature and save energy.

NOTE: The SLEEP function is only available
under Cooling, Heating and AUTO operations.

When the FRESH function is initiated, the
Ionizer/Plasma Dust Collector(depending on
models) is energized and will help to remove
pollen and impurities from the air.

SHORTCUT

FAN
SPEED

TIMER
OFF

LOCK

LED
FOLLOW ME

MODE

SWING

TEMP

RESET

TIMER
ON

TURBO
SELF CLEAN

DIRECT

SLEEP
FRESH