INVENTOR P2MVI-09, A2MVI-24, A2MVI-12, A2MVI-18, P2MVI-12 Owner's Manual
...
Wall Mounted Unit
A2MVI-09/A2MVO-09
A2MVI-12/A2MVO-12
A2MVI-24/A2MVO-24
A2MVI-18/A2MVO-18
P2MVI-09/P2MVO-09
P2MVI-12/P2MVO-12
P2MVI-18/P2MVO-12
P2MVI-24/P2MVO-24
11
CONTENTS
Use the remote controller within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
Location of the remote controller.
8m
The remote controller is powed by two dry batteries(R03/LR03X2) housed in the
rear part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new batteries,placing the(+) and (-)
ends correctly.
(3) Reattach the cover by sliding it back into position.
NOTE: When the batteries are removed, the remote controller erases all programming. After inserting new batteries, the remote controller must be reprogrammed.
Replacing batteries
Handling the remote controller
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller. either move
these appliances or consult your local dealer.
22
CAUTIONS
Do not mix old and new batteries or batteries of different types.
Do not leave the batteries in the remote controller if they are not
going to be used for 2 or 3 months.
Do not dispose batteries as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.
2
3
5
8
9
9
9
10
10
11
14
15
15
Handling the remote controller ......................................................
Remote controller Specifications...................................................
Function buttons .................. .........................................................
Indicators on LCD ..........................................................................
How to use the buttons .................................................................
Auto operation.................................................................................
Cooling/Heating/Fan operation......................................................
Dehumidifying operation ...............................................................
Adjusting air flow direction............................................................
Timer operation...............................................................................
SLEEP/FRESH function..................................................................
LED/FOLLOW ME function ...........................................................
TRUBO/SELF CLEAN function ......................................................
NOTE: Replace the batteries when there is no receiving beep from the indoor
unit or if the transmission indicator on the remote controller fails to light.
Model
Rated Voltage
8m
3.0V(Dry batteries R03/LR03 2)
Remote Controller Specifications
1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only model without), and FAN.
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display).
Environment
Signal Receiving
Range
Performance Feature
33 44
RG35A(2)/BG(C)EF,RG35A1(4)/BG(C)EF,RG35B/BG(C)E,RG35C/BG(C)E, RG36B3/BGE
RG36A(1)/BG(C)EF
RG36A2/BG(C)EF RG36C/BG(C)E
RG35A4/BG(C)EF
RG35A(2)/BG(C)EF
RG35B/BG(C)E
RG35C/BG(C)E
RG36A(1)/BG(C)EF,RG36A2/BG(C)EF,RG36B(1)/BG(C)E,RG36C/BG(C)E
-5 C 60 C
~~
TURBO
SELF
CLEAN
TURBO
SLEEP
FRESH
SLEEP
SLEEP
SHORT
CUT
SHORT
CUT
SHORT
CUT
TIMER
ON
TIMER
ON
TIMER
ON
TIMER
OFF
TIMER
OFF
TIMER
OFF
LOCK
LOCK
LOCK
RESET
RESET
RESET
LED
FOLLOW
ME
LED
FAN
SPEED
FAN
SPEED
FAN
SPEED
DIRECT
DIRECT
DIRECT
SWING
SWING
SWING
MODE
MODE
O
M
R
E
Y
M
MODE
TEMP
TEMP
TEMP
MODE
MODE
MODE
MODE
SWING
SWING
SWING
SWING
TEMP
TEMP
TEMP
TEMP
SHORTCUT
SHORTCUT
SHORTCUT
SHORTCUT
FAN
SPEED
FAN
SPEED
FAN
SPEED
FAN
SPEED
TIMER
OFF
TIMER
OFF
TIMER
OFF
TIMER
OFF
RESET
RESET
RESET
RESET
LOCK
LOCK
LOCK
LOCK
LED
FOLLOW ME
LED
FOLLOW ME
LED
TIMER
ON
TIMER
ON
TIMER
ON
TIMER
ON
TURBO
SELF CLEAN
TURBO
FP
TURBO
DIRECT
DIRECT
DIRECT
DIRECT
SLEEP
FRESH
SLEEP
SLEEP
SLEEP
NOTE: There is only slight difference on the appearance between RG35
series and RG 36 series. The operations and functions of the buttons are
the same. Some buttons have two functions, some buttons have only one
function, for example: and . Please refer to the above
illustrations for details.
SLEEP
FRESH
SLEEP
RG35A1/BGEF
SLEEP
SHORT
CUT
TIMER
ON
TIMER
OFF
LOCK
RESET
LED
FAN
SPEED
DIRECT
SWING
MODE
TEMP
RG36B(1)/BG(C)E
RG36B3/BGE
TURBO
FP
ON/OFF
ON/OFF
ON/OFF
ON/OFF
Modles of RG36B(3)/BG(C)E do
not have FP function.
F
E
O
M
L
L
W
O
Loading...