Throughout this catalog you will notice letters to draw your attention to specific footnotes which are located at the
bottom of the page or below specified charts.
Parts Catalog Usage Guide
To order call toll free 1-800-333-6900, or www.invacare.com
The information contained in this document is subject to change without notice. This catalog contains
service parts for Form No. 04-041. If you have any questions regarding this catalog, please contact one
of our Customer Service Representatives.
For Customer Service Support Call:
1-800-333-6900
For Faxed In Orders Call:
1-800-678-4682 or
1-440-366-0709
For Technical Service Call:
1-800-832-4707
Literature Can Be Found at:
www.invacare.com or
1-800-828-6272
SYMBOL DEFINITION
Examples:
A,B,C etc.
NOTE:
NLA
= Special Comments
= General information pertaining to that specific page
= No Longer Available
HARDWARE MEASUREMENTS
The measurements for the hardware will be listed as follows:
Screws, Bolts
Washers
Spacers
For your convenience, we have supplied an area for you to list your Invacare Representatives.
Cable Tie (5-5/8" Long)147
Locknut (5/16-18)148
Washer (5/16 x 3/4 x 1/16")199
Bolt, Hex Head Cap (1/4-20 x 3/4")1210
Washer (1/4 x 1/2 x 1/16")1211
Screw, Hex Head Cap w/ Patch (5/16-18 x 7/8")1912
Locknut (1/4-20)1213
Screw, Phillips Pan Head Tap (#10-32 x 1/2")1214
1113357Kit, Battery Box Door Assembly, 22NF Short1115B,D
Screw, Hex Head Cap w/ Patch (5/16-18 x 7/8")128
Washer, Flat (21/64 x 53/64 x 7/64")129
Screw, Socket Head Cap (1/4-20 x 3/4")1310
Bolt, Hex Head Cap (1/4-20 x 3/4")1311
Washer (1/4 x 1/2 x 1/16")1312
Screw, Hex Head (1/4-20 x 1-5/8")1413
Screw, Phillips Pan Head (#10-32 x 5/8")1414
Bracket, Front Upper Seat1115
Bracket, Front Lower Seat1116
Screw, Hex Head Cap with Patch (5/16-18 x 3/4")1217
Package, Cable Ties (5-5/8" Long)1218
Locknut (1/4-20)1619
Washer, Flat (3/16 x 5/8 x 1/16")1420
Screw, Phillips Pan Head Tap (#10-32 x 1/2")1221
1125776Kit, Battery Box Door Elevate Assembly, 22NF
C - Blank Logo Decal is no longer available and no longer required for item number 25 Invacare Medallion Decal.
NOTE:
Motor
Elevate
For ASBA/ADJASBA, Conventional and Contoura Seating
The Battery Boxes are non-serviceable parts. Call Technical Services for assistance (1-800-832-4707)
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
19
Page 21
Battery Support Bracket Assembly
For TRBKTS Option
Form No.
04-041
20
To order call toll free 1-800-333-6900, or www.invacare.com
Page 22
Battery Support Bracket Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1139537Kit, Battery Support Bracket Assembly - For 22NF
Batteries
111A
Screw, Hex Head Cap w/ Patch (1/4-20 x 1/2")142
Locknut (1/4-20)143
Bracket, Battery Support, Black114
1139538Kit, Battery Support Bracket Assembly - For GP24
Batteries
111A
Screw, Hex Head Cap w/ Patch (1/4-20 x 1/2")142
Locknut (1/4-20)143
Bracket, Battery Support, Black114
1139539Kit, Battery Support Bracket Assembly - For
Invisible Super Low Tilt System w/ 22NF Batteries
111B
Bracket, Battery Support, Black114
Screw, Hex Head Cap w/ Patch (1/4-20 x 1/2")145
1139540Kit, Battery Support Bracket Assembly - For Vent
"Ready" System w/ 22NF Batteries
111A
Screw, Hex Head Cap with Patch (1/4-20 x 5/8")142
Locknut (1/4-20)143
Bracket, Battery Support, Black114
1139541Kit, Battery Support Bracket Assembly - For Vent
"Option" System w/ 22NF Batteries
111B
Bracket, Battery Support, Black114
Screw, Hex Head Cap w/ Patch (1/4-20 x 1/2")145
1139867Kit, Battery Support Bracket Assembly - For Elevate
"Option" System w/ 22NF Batteries
111B
Bracket, Battery Support, Black114
Screw, Hex Head Cap w/ Patch (1/4-20 x 1/2")145
A - Includes items 2-4
B - Includes items 4 and 5
NOTE:
For TRBKTS Option
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
21
Page 23
Battery Tray Assembly and Wire Harnesses For Vent Tray
(3) 22NF Batteries
Form No.
04-041
22
To order call toll free 1-800-333-6900, or www.invacare.com
Page 24
Battery Tray Assembly and Wire Harnesses For Vent Tray
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1120363Battery Wire Harness with Terminal Hardware,
22NF Rear
111B,A
1120362Battery Wire Harness with Terminal Hardware,
22NF - Front
112B,A
1121143Battery Wire Harness with Terminal Hardware,
22NF Vent
113B,A
16721X000Locknut (1/4-20)164
1095502Package, Cable Ties (11-1/2" Long)1015
1096799Screw, Hex Flange Whiz Lock (1/4-20 x 7/8")146
1121124Battery Strap Assembly, 22NF and GP24127
1121125Battery Strap Assembly For Vent, 22NF 118
1117186Bracket, Battery Tray Stop, Black119
90017X000Screw, Phillips Pan Head (#10-32 x 5/16")1210
1121142Battery Tray Assembly, TDX 22NF For Vent1111C
1121029Kit, Vent Battery Harness Assembly with Hardware1112D
Vent Battery Harness1113
Vent Battery Extension Harness1114
Screw, Phillips Pan Head (#8-16 x 5/8")1215
Cable Tie (5-5/8" Long)1416
Grommet, Rubber1117
1139531Kit, Vent Battery Harness Assembly with Hardware
For TRBKTS Option
1112D
Vent Battery Harness1113
Vent Battery Extension Harness For TRBKTS
Option
1114
Screw, Phillips Pan Head (#8-16 x 5/8")1215
Cable Tie (5-5/8" Long)1416
Grommet, Rubber For TRBKTS Option1117
1095503Package, Cable Ties (5-5/8" Long)10116
1055747Grommet, Rubber1117
1137236Grommet, Rubber For TRBKTS Option1117
A - Individual components are not available for the battery wire harnesses
B - Includes items 4-6
C - Includes items 7-10
D - Includes items 13-17
NOTE:
(3) 22NF Batteries
Form No.
04-041
23
To order call toll free 1-800-333-6900, or www.invacare.com
Page 25
Battery Wire Harnesses, Sensor Proximity Switch,
Extension Cables and Energy Chain
For All Elevate Systems
Form No.
04-041
24
To order call toll free 1-800-333-6900, or www.invacare.com
Page 26
Battery Wire Harnesses, Sensor Proximity Switch,
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1124657Bracket, Wire Harness Mounting111
1114308Screw, Phillips Pan Head Tap (#10-32 x 1/2")142
1124654Bracket, Upper Energy Chain Mounting113
1124655Bracket, Lower Energy Chain Mounting114
1122586Sensor, Proximity Switch115
1125742Kit, Sensor Proximity/Actuator Switch Mounting
Hardware
116A
Nut, Hex Keps (#4-40)127
Washer, Plain (1/8 x 5/16 x 1/32)128
Screw, Phillips Pan Head (#4-40 x 3/8")129
1125745Kit, Energy Chain with Mounting Hardware1110F
Screw, Phillips Pan Head Tap (#10-32 x 1/2")1211
1024001Sensor, Actuator Switch1112
1123277Cable, Joystick Extension 48"1113
1125743Kit, Battery Harness with Mounting Hardware,
Elevate
1114B
Nut, Keps (#6-32)1615
Screw, Phillips Pan Head (#6-32 x 7/8")1616
Cable Tie (5-5/8" Long)1318
Washer (1/4 x 1/2 x 1/16")1419
1141968Kit, Battery Harness with Mounting Hardware,
Elevate with TRBKTS option
1114C
Nut, Keps (#6-32)1615
Screw, Phillips Pan Head (#6-32 x 7/8")1416
Screw, Phillips Pan Head (#6-32 x 1-1/8")1217
Cable Tie (5-5/8" Long)1318
Washer (1/4 x 1/2 x 1/16")1419
Spacer (1/4 x 5/8 x 3/8")1220
1125740Kit, Rear Battery Harness with Terminal Hardware1121D
Locknut (1/4-20)1222
Cable Tie (11-1/2" Long)1423
Screw, Hex Flange Whiz Lock (1/4-20 x 7/8")1124
1125741Kit, Front Battery Harness with Terminal Hardware1125E
Screw, Socket Head (1/4-20 x 3/4")1210
1154125Kit, MK6i Connector Bracket and Threaded Insert1111B
1154126Kit, MK6i Connector Bracket Cover and Attaching
Screw
1112C
Cover, MK6i Connector Bracket118
Screw, Thumb (#10-32 x 1/2")119
1140034Module, Recline Integrated Actuator (RIAM) MK6i112
1145403Bracket, MK6i Recline Integrated Actuator Module
(RIAM)
113
1021742Screw, Phillips Pan Head (#4-40 x 1/2")114
1025195Locknut (1/4-20)125
1009838Screw, Socket Head (1/4-20 x 3/4")1210
A - Includes items 2-10. Kit is used for Conventional and Contoura Seating
B - Includes items 6 and 7
C - Includes items 8 and 9. When converting in the field for the first time to add the Connector Bracket Cover that was
introduced 6/11/08, items 11 and 12 must be ordered together.
NOTE:
For Formula Recline and Tilt/Recline
Form No.
04-041
60
To order call toll free 1-800-333-6900, or www.invacare.com
Page 62
Seat Pan and Mounting Hardware
Elevate Only For ASBA Seating (Before 7/5/05)
Form No.
04-041
61
To order call toll free 1-800-333-6900, or www.invacare.com
Page 63
Seat Pan and Mounting Hardware
#1 Seat Pan
16" Deep - 18" Deep
Chair Width16" Deep17" Deep18" Deep
10660351066024106601316" W
10660361066025106601417" W
10660371066026106601518" W
10660381066027106601619" W
10660391066028106601720" W
10660401066029106601821" W
10660411066030106601922" W
#1 Seat Pan
19" Deep - 22" Deep
Chair Width19" Deep20" Deep21" Deep22" Deep
106607910660681066057106604616" W
106608010660691066058106604717" W
106608110660701066059106604818" W
106608210660711066060106604919" W
106608310660721066061106605020" W
106608410660731066062106605121" W
106608510660741066063106605222" W
Elevate Only For ASBA Seating (Before 7/5/05)
Form No.
04-041
62
To order call toll free 1-800-333-6900, or www.invacare.com
Page 64
Seat Pan and Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart#1 Seat Pan 16"-18" Depth111
See Chart#1 Seat Pan 19"-22" Depth111
1070459Kit, Seat Pan Mounting Hardware116
Screw, Hex Head (1/4-20 x 1-5/8")122
Screw, Hex Head (1/4-20 x 1-1/2") 143
Spacer (1/4 x 3/8 x 3/16")144
Locknut (1/4-20)165
Elevate Only For ASBA Seating (Before 7/5/05)
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
63
Page 65
#1 Contoura Seat Cushion Assembly
Chair Width21" Deep22" Deep16" Deep17" Deep18" Deep19" Deep20" Deep
N/AN/A
1132986
1132985
1132984
1132983
1132982
16" W
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
N/AN/A
1132991
1132990
1132989
1132988
1132987
18" W
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
1132998
1132997
1132996
1132995
1132994
1132993
1132992
20" W
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
1133003
1133002
1133001
1133000
1132999
N/AN/A22" W
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
1133008
1133007
1133006
1133005
1133004
N/AN/A24" W
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
A - Cushion Foam is not available separately. NOTE:
#2 Contoura Seat Cushion Cover
Chair Width21" Deep22" Deep16" Deep17" Deep18" Deep19" Deep20" Deep
N/AN/A1132957113295611329551132954113295316" W
N/AN/A1132962113296111329601132959113295818" W
113296911329681132967113296611329651132964113296320" W
11329741132973113297211329711132970N/AN/A22" W
11329791132978113297711329761132975N/AN/A24" W
Seat Cushion Assembly
Contoura Seating
Contoura Backs for ADJASBA Seating do not use the 24" wide selection
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
64
Page 66
Single Liners
Width
16"-17"
High
18"-19"
High
20"
High
21"-22"
High
23"-24"
High
1054529104515910689471045207888104517516" W
1054530104516010689481045208104517617" W
1054531104516110689491045209104517718" W
Back Upholstery, Nylon
Elevate Only For ASBA/ADJASBA Seating
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
65
Page 67
Back Upholstery, Nylon
Dual Liners
Width
16"-17"
High
18" - 19"
High
20"
High
21" - 22"
High
23" - 24"
High
1054534104516410689521045212104518016" W
1054535104516510689531045213104518117" W
1054536104516610689541045214104518218" W
1054537104516710689551045215104518319" W
1054538104516810689561045216104518420" W
1054539104516910689571045217104518521" W
1054540104517010689581045218104518622" W
NOTE: Dual liner back upholstery is used with chairs that have a seat deeper than 17" or back wider than 18".
Back Upholstery Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See ChartSingle Liners11A
See ChartDual Liners - Nylon 11A
1026298Screws with Washers (#10 x 7/8")21A
A - Not Shown
NOTE:
Elevate Only For ASBA/ADJASBA Seating
Form No.
04-041
66
To order call toll free 1-800-333-6900, or www.invacare.com
Page 68
Conventional Back without Mounting Hardware
NOTE: Extruded back canes come in one back height only. Back cane material height for extruded back
canes measure approximately 20-1/2". Overall back height from the seat pan to top of the extruded back
cane is approximately 22-1/2". Only the Back Assembly needs to be replaced when changing back
heights.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
04-041
67
To order call toll free 1-800-333-6900, or www.invacare.com
Back cover and foam are sold as a back cushion assembly only. Chart reflects chair width and the actual back cushion width will be 1" wider
than the chair width.
Back cover and foam are sold as a back cushion assembly only. Chart reflects chair width and the actual back cushion width will be 1" wider
than the chair width.
NOTE: Extruded back canes come in one back height only. Back cane material height for extruded back
canes measure approximately 20-1/2". Overall back height from the seat pan to top of the extruded back
cane is approximately 22-1/2". Only the Back Assembly needs to be replaced when changing back
heights.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
04-041
70
To order call toll free 1-800-333-6900, or www.invacare.com
Page 72
Conventional Back without Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart#1 Back Assembly without Hardware 16"-20" Wide111
See Chart#1 Back Assembly without Hardware 21"-24" Wide111
See Chart#2 Back Pan with Vinyl Edge Trim 16"-20" Wide112
See Chart#2 Back Pan with Vinyl Edge Trim 21"-24" Wide112
See Chart#3 Back Cushion Assembly 16"-20" Wide113
See Chart#3 Back Cushion Assembly 21"-24" Wide113
A - Hook Fastener Adhesive kit is used to attach the Back Cover to the Back Pan and must be ordered when a new Back Pan
or Back Assembly is requested.
NOTE:
NOTE: Extruded back canes come in one back height only. Back cane material height for extruded back
canes measure approximately 20-1/2". Overall back height from the seat pan to top of the extruded back
cane is approximately 22-1/2". Only the Back Assembly needs to be replaced when changing back
heights.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
71
Page 73
Contoura Back without Mounting Hardware
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights. Contoura Backs for ADJASBA Seating do not use the 24" wide selection
Form No.
04-041
72
To order call toll free 1-800-333-6900, or www.invacare.com
Page 74
Contoura Back without Mounting Hardware
#1 Back Assembly without Hardware 16", 18", 20", 22", 24" Wide
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights. Contoura Backs for ADJASBA Seating do not use the 24" wide selection
Form No.
04-041
73
To order call toll free 1-800-333-6900, or www.invacare.com
Page 75
Contoura Back without Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart#1 Back Assembly without Hardware 16", 18", 20",
22", 24" Wide
111
See Chart#2 Back Pan with Vinyl Edge Trim 16", 18", 20", 22",
24" Wide
112
See Chart#3 Back Cushion Assembly 16", 18", 20", 22", 24"
Wide
113
1125725Hook Fastener w/ Adhesive Back (1" Wide x 48"
Long)
114
1125724Edge Trim, Vinyl Black (96" Long) Cut-To-Length115
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights. Contoura Backs for ADJASBA Seating do not use the 24" wide selection
Form No.
04-041
74
To order call toll free 1-800-333-6900, or www.invacare.com
Page 76
Back Mounting Hardware
Conventional Tilt
Form No.
04-041
75
To order call toll free 1-800-333-6900, or www.invacare.com
Page 77
Back Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125757Kit, Back Mounting Hardware For Conventional Tilt111A
Locknut (1/4-20)142
Washer (1/4 x 23/32 x 1/16")183
Spacer, Coved (1/4 x 7/8 x 7/16")144
Spacer (1/4 x 5/8 x 3/8")145
Screw, Socket Button Head (1/4-20 x 2")146
A - Includes items 2-6
NOTE:
Conventional Tilt
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
76
Page 78
Back Mounting Hardware
Conventional Recline and Tilt/Recline
Form No.
04-041
77
To order call toll free 1-800-333-6900, or www.invacare.com
Page 79
Back Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125756Kit, Back Mounting Hardware For Conventional
Recline and Tilt/Recline
111A
T-Nut (1/4-20)182
Locknut (1/4-20)143
Bracket, Angled Back, Black144
Washer (1/4 x 1/2 x 1/16")185
Screw, Hex Head Cap w/ Patch (1/4-20 x 1/2")186
Washer (1/4 x 23/32 x 1/16")147
Screw, Socket Head (1/4-20 x 3/4")148
A - Includes items 2-8
NOTE:
Conventional Recline and Tilt/Recline
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
78
Page 80
Back Mounting Hardware
Contoura Tilt
Form No.
04-041
79
To order call toll free 1-800-333-6900, or www.invacare.com
Page 81
Back Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125755Kit, Back Mounting Hardware For Contoura Tilt111A
T-Nut (1/4-20)1162
Locknut (1/4-20)143
Washer (1/4 x 1/2 x 1/16")1164
Bracket, Back Mounting, Black145
Screw, Hex Head Cap w/ Patch (1/4-20 x 1/2")1166
Washer (1/4 x 23/32 x 1/16")147
Screw, Socket Head (1/4-20 x 3/4")148
Bracket, Contoura Shear Lock Out129
A - Includes items 2-9
NOTE:
Contoura Tilt
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
80
Page 82
Contoura Back Mounting Hardware
ADJASBA Only
Form No.
04-041
81
To order call toll free 1-800-333-6900, or www.invacare.com
Page 83
Contoura Back Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1140945Kit, Contoura Back Mounting Hdwr. - Round Canes111A
Bracket, Back Mounting, Black - Front142
Screw, Phillips Oval Head Countersunk (#10-16 x
7/8")
123
Screw, Socket Head (1/4-20 x 3/4")184
Washer (1/4 x 23/32 x 1/16")185
Locknut (1/4-20)186
Bracket, Back Mounting, Black - Rear147
A - Includes items 2-7
NOTE:
ADJASBA Only
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
82
Page 84
Back Mounting Hardware
Contoura Recline and Tilt/Recline
Form No.
04-041
83
To order call toll free 1-800-333-6900, or www.invacare.com
Page 85
Back Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125754Kit, Back Mounting Hardware For Contoura Recline
and Tilt/Recline
111A
T-Nut (1/4-20)142
Bracket, Back Mounting, Black123
Washer (1/4 x 1/2 x 1/16")144
Screw, Hex Head Cap w/ Patch (1/4-20 x 1/2")145
Locknut (1/4-20)166
Washer (1/4 x 23/32 x 1/16")167
Screw, Socket Head (1/4-20 x 3/4")168
A - Includes items 2-8
NOTE:
Contoura Recline and Tilt/Recline
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
84
Page 86
Prop Rod Assembly
Contoura Tilt
Form No.
04-041
85
To order call toll free 1-800-333-6900, or www.invacare.com
Page 87
Prop Rod Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125764Kit, Prop Rod Assembly Contoura Tilt111B,C,A
Screw, Socket Head Shoulder (3/8 x 2")112
Washer, Flat (5/16 x 5/8 x 1/16")113
Locknut (5/16-18)124
Kit, Top Prop Rod with Bushings115
Tube, Middle Prop Rod116
Kit, Bottom Prop Rod Tube with Bushings117
Screw, Socket Head Cap w/ Patch (3/8-16 x 1-1/2")128
Locknut, Low Profile (3/8-16)129
Screw, Socket Head Shoulder (3/8 x 1-3/4")1110
Bushing, Actuator Motor (3/8 x 3/4 x 5/32")1211
Bushing, Actuator Motor (3/8 x 3/4 x 1/2")1112
A - Includes items 2-12
B - When a vent tray is present, item 11 located on the top side of the prop rod is replaced with item 12
C - Relocation of holes were made 7/5/05 for items 5, 6 and 7. Item 1 must be ordered for chairs manufactured before 7/5/05.
NOTE:
Contoura Tilt
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
86
Page 88
Back Recline Shear Link Assemblies
Form No.
04-041
87
To order call toll free 1-800-333-6900, or www.invacare.com
Page 89
Back Recline Shear Link Assemblies
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125758Kit, Recline Shear Link Assembly Conventional211A
Screw, Hex Head Cap with Patch (1/4-20 x 5/8")142
Washer (1/4 x 1/2 x 1/16")143
Plate, Shear Adapter124
T-Nut (1/4-20)145
Locknut, Low Profile (3/8-16)146
Washer, Flat (3/8 x 11/16 x 1/16")147
Link, Recline Shear - Right118
Link, Recline Shear - Left118
Stand-Off, Shear Recline Link149
1128365Kit, Recline Link Assembly Contoura 16" Wide2110B
Screw, Hex Head Cap with Patch (1/4-20 x 5/8")1411
Washer (1/4 x 1/2 x 1/16")1412
T-Nut (1/4-20)1413
Adapter, Recline Shear Contoura 16" Wide1214
Locknut, Low Profile (3/8-16)1415
Washer, Flat (3/8 x 11/16 x 1/16")1416
Link, Recline Shear - Right1117
Link, Recline Shear - Left1117
Stand-Off, Shear Recline Link1418
1125759Kit, Recline Link Assembly Contoura 18" Wide2110B
Screw, Hex Head Cap with Patch (1/4-20 x 5/8")1411
Washer (1/4 x 1/2 x 1/16")1412
T-Nut (1/4-20)1413
Adapter, Recline Shear Contoura 18" Wide1214
Locknut, Low Profile (3/8-16)1415
Washer, Flat (3/8 x 11/16 x 1/16")1416
Link, Recline Shear - Right1117
Link, Recline Shear - Left1117
Stand-Off, Shear Recline Link1418
1125760Kit, Recline Link Assembly Contoura 20" Wide2110B
Screw, Hex Head Cap with Patch (1/4-20 x 5/8")1411
Washer (1/4 x 1/2 x 1/16")1412
T-Nut (1/4-20)1413
Adapter, Recline Shear Contoura 20" Wide1214
Locknut, Low Profile (3/8-16)1415
Washer, Flat (3/8 x 11/16 x 1/16")1416
Link, Recline Shear - Right1117
Link, Recline Shear - Left1117
Stand-Off, Shear Recline Link1418
1128366Kit, Recline Link Assembly Contoura 22" Wide2110
Screw, Hex Head Cap with Patch (1/4-20 x 5/8")1411
Washer (1/4 x 1/2 x 1/16")1412
T-Nut (1/4-20)1413
Form No.
04-041
88
To order call toll free 1-800-333-6900, or www.invacare.com
Contoura Backs for ADJASBA Seating do not utilize a Spreader Bar Assembly.
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
94
Page 96
Back Canes and Spreader Bars
A - 21"-24" High Straight Back Canes with Push Handles are only offered On-Chair when the Back Upholstery is omitted
B - Chairs with Contoura Backs use 18" high Straight Back Canes with Push Handles.
NOTE:
NOTE: Back Cane Assemblies include Foam Grips and Plug Buttons where shown
For ADJASBA Seat (16"-22" Wide) After 7/4/05
Contoura Backs for ADJASBA Seating do not utilize a Spreader Bar Assembly.
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
95
Page 97
Back Cane Attaching Hardware
For ADJASBA Seat (16"-22" Wide) After 7/4/05
Form No.
04-041
96
To order call toll free 1-800-333-6900, or www.invacare.com
Page 98
Back Cane Attaching Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1133755Kit, Back Cane Mounting Hardware (Pair)211A
Screw, Hex Head Cap (5/16-18 x 1")142
Washer, Flat (21/64 x 53/64 x 7/64")143
Locknut (5/16-18)144
Locknut (5/16-24)125
Screw w/ Lug (5/16-24 x 1-3/8")126
A - Includes items 2-6
NOTE:
For ADJASBA Seat (16"-22" Wide) After 7/4/05
Form No.
04-041
To order call toll free 1-800-333-6900, or www.invacare.com
97
Page 99
Solid Straight Back Canes w/o Push Handles and
Mounting Hardware
Conventional Tilt and Tilt w/ BPO Option
Form No.
04-041
98
To order call toll free 1-800-333-6900, or www.invacare.com
Page 100
Solid Straight Back Canes w/o Push Handles and
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1128394Kit, Back Cane w/o Push Handle, Solid Straight w/
Plug Button - Right
111A,B
1128395Kit, Back Cane w/o Push Handle, Solid Straight w/
Plug Button - Left
111A,B
1128396Kit, Back Canes w/o Push Handle, Solid Straight w/
Plug Button (Pair)
111A
1027097Plug Button, Black (3/4")112
1125733Kit, Solid Straight Back Cane w/o Push Handle,
Mounting Hardware
113C
Washer, Flat (21/64 x 53/64 x 7/64")124
Screw, Hex Head Cap (5/16-18 x 1")125
Locknut (5/16-18)126
1079247Washer, Flat (21/64 x 53/64 x 7/64")124
1028478Screw, Hex Head (5/16-18 x 1-1/4")125
1026158Locknut (5/16-18)126
A - Back height from the seat pan to the top of the back cane will measure approximately 20-1/2" high.
B - After 4/3/05 ALL Solid Straight Back Canes have a hole bored out to accommodate a Push Handle Attachment Option. For
chairs manufactured before 4/4/05 it is recommended to order back canes in pairs to match.
C - Includes items 4-6
NOTE:
Mounting Hardware
Conventional Tilt and Tilt w/ BPO Option
Form No.
04-041
99
To order call toll free 1-800-333-6900, or www.invacare.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.