LUMEN 1000 & ACCESSORIES
USER GUIDE
1
Device Summary
Lumen 1000 is a BTE hearing aid that receives audio signal and converts into acoustic output. A
rocker switch control provides the user interface input. In addition to providing volume control,
the Up and Down keys of the rocker switch can be used to toggle between different pre-loaded
audio programs, audio streaming being one of them. Lumen 1000 receives audio signals
transmitted wirelessly from paired accessories (linkstream, voicestream and flexstream). The LiPo battery in the unit is charged using a customized Lumen 1000 Charger device. Each device
has a unique serial number.
Linkstream is designed to pick up audio signal from a television and relaying it wirelessly to the
hearing aid device. . The device is be powered by a 120-240V wall power adapter via a mini USB
socket and picks up the TV audio through an audio cord connection to the TV audio output. It
uses a high efficiency external antenna to allow link distances of 5 meters. An LED indicates It
may need to have a function button and LED. It is also be used to program Lumen 1000 device
when connected to a PC.
Voicestream is designed to pick up nearby sounds through two internal microphones, amplifies
those sounds, and converts them into a digital wireless transmission to the Lumen 1000 hearing
aid. A membrane switch serves as a user interface for mode and volume control. The use of
more than one microphone allows it to function in OMNI and DIRECTIONAL modes. MicroUSB
cable is used to recharge the Li-Po battery.
Typical use environments include restaurants, cars, meetings etc.
Flexstream draws power from the host iPhone, iPod Touch, or iPad and sends audio and/or
command information wirelessly to Lumen 1000. It will connect to the host via the 30 pin dock
connector. The use of more than one microphone allows it to function in OMNI and
DIRECTIONAL modes.
Typical use scenarios include listening to iTunes player, cell phone calls, reloading Lumen 1000
firmware from a host app.
2
Lumen 1000 Charger will draw power from one AAA alkaline battery and or microUSB cable
connected to a wall outlet. The charger has a nest to hold the Lumen 1000 hearing aid and the
entire unit is small enough to go into a shirt or coat pocket or purse compartment. The device
has a LED to indicate charging status.
3
Lumen 1000 Hearing Aid
Lumen 1000 Device Illustration
Device Description
1 Lumen 1000 Unit
2 Clear Tube System
3 Dome Shaped Earbud
4 Rocker Switch
Program Switch
Volume Control
5 Charging Contact Pins
6 Lasermarking Area
Charging procedure and installation in charger
Charger Description
4
2
Cover Slide
3
LED Charge Indicator
Lumen 1000 Charger Device Illustration
Device Description
1 Lumen 1000 Charger Unit
4 Batter Door
5 MicroUSB Port
6 Dummy Lumen 1000
7 AAA Battery
8 MicroUSB Cable
Charging with mUSB cable
Charging with Battery
5
Lumen 1000 can be recharged about 5-8 times with one AAA battery.
Installing Lumen 1000 into charger
st
Charge Lumen 1000 fully before 1
use. Typical charge time is about 2.5hrs.
After charging is complete the red LED light on charger automatically goes OFF
Note: Charger cover door can be closed only when Lumen 1000 with thin tube is inserted.
Lumen 1000 with Earhook cannot be closed in charger.
Lumen 1000 can be inserted only one way
6
Installing sound tube to Lumen 1000
Choose tip and length that fits best (most comfortable) or as recommended by audiologist
Exact tube availability to be determined by the customer
Verify Lumen 1000 is charged
Press rocker switch to hear beep ?? or pair with accessory ??
Using Lumen 1000
Wearing Lumen 1000
7
Ear Tube and Tip
Replacing ear tube & tip
Your ear tube & tip will come connected. For optimal performance, replace ear tube & tip
every three months. Removing ear tube & tip from device: Grasp the “device end” of the ear tube;
gently turn ~90 degrees and pull to remove the ear tube from the device. Attaching ear tube & tip to
device: Gently push the “device end” of the ear tube onto the device until it snaps into position.
Cleaning ear tube & tip
Between replacements, you’ll need to clean the ear tube & tip with a cleaning wire, typically once a
week. Remove the ear tube & tip from device. Thread the cleaning wire through the ear tube, starting at
the “device end,” until it comes out at the “ear tip end,” then pull the cleaning wire all the way through.
Be sure to wipe off the wire before the next cleaning. Note: Ensure the wire goes through the ear tube
in only one direction, from “device end” to “ear tip end.” Do not reverse the wire back through the ear
tube. Clean the ear tip with a dry cloth
8
Removing ear hook from device:
Grasp the “device end” of the ear hook; gently turn ~90 degrees and pull to remove the ear hook from
the device.
Attaching ear hook to device:
Gently push the “device end” of the ear hook onto the device until it snaps into position.
Rocker switch functions
Rocker Switch Presses Function
Short up Volume up (default) or program up (configurable in MT)
Short down Volume down (default) or program down (configurable in MT)
Medium Up (default 3s, but configurable in MT) volume up or program up (default) (configurable in MT)
Medium Down (default 3s, but configurable in MT) volume down or program down (default) (configurable in MT)
Long Down with power on (default 5s, but will be configurable in
MT)
Long Down with power off (default 5s, but will be configurable in
MT)
Extra Long Down with power off (default 10s, but will be
configurable in MT)
Using with telephones and cellular phones
a. Telephones
i. Hold the phone handset as you normally would. Move the handset up slightly to
find the position that sounds best to you. If you encounter whistling (feedback),
tilt the phone handset at an angle until the whistling stops.
b. Cellular phones
i. Lumen 1000 is designed to comply with the most stringent Standards of
International Electromagnetic Compatibility. However, not all cell phones are
device compatible. Please check with your cellular phone carrier.
c. Telecoils - NA
Shutdown
Wakeup
Wakeup and enter pairing mode
Using Lumen 1000 with audio Accessory
2. Using Companion Mic
a. Typical use scenarios (sketch with stickfigures)
i. Cars, restuarants etc.
b. Describe CM with PICTURE showing labels identifying components
9
voicestream Device Illustration
Device Description
1 voicestream Unit
2 Clip
3 MicroUSB Port
4 Lasermarking Area
5 LED Indicator
6 Mic Cover
7 Mic Ports
8 Mode Button
9 Volume Control
Charging CM
10
Press -
Volume down one step
Press M
Press and release to toggle between Omni,
LED status table describing charge level
Press -/+ Blinks once
Press M OMNI mode
Directional mode,
Off mode
LED ON Indicates Charging
LED OFF Fully Charged or Off mode
Low Battery
Indicator
0.1 seconds ON & 0.1 second Off every 5
seconds
Description of button presses (including pairing)
Press + Volume up one step
Directional and Off
Press M Pairing with Lumen 1000 - Press and hold for 10
seconds, could be in any mode including Off
Charge device with microUSB cable when not in use.
Using TVA
c. Typical use scenarios (sketch with stickfigures)
i. Home
d. Describe TVA with PICTURE showing labels identifying components
Device Description
1 linkstream Unit
2 Switch Button
11
Linkstream Device Illustration
3 LED
4 Antenna
5 MiniUSB Port
6 3.5mm Audio Port
7 Anti-Slip Pads
8 Product labeling
Positioning antenna
Antenna should be in upright position when in use
Connecting TVA to
Wall outlet, 3.5mm audio cable
12
e. Description of button presses (including pairing)
3. Using IPODA
i. LED status
1. ON/Off. Press and release button to Turn On/Off the LinkStream. LED
will light when on
2. Pairing mode. With the LinkStream On, Press and hold the button for 3
(??) seconds. LED will blink during pairing mode.
ii. Table capturing pairing scenarios – To pair LinkSteam accessory with a Lumen
1000 ear piece,
1. If Lumen 1000 is in standby mode goto step 2. Press and hold down
button for 5 seconds, the HA will enter Standby mode
2. Continue pressing the down button for 10 seconds. Afer 5 seconds, the
Lumen 1000 will wake up from Standby mode. Continue holding for the
remainder of the 10 seconds to enter pairing mode. (In pairing mode the
Lumen 1000 will generate a series of beeps that lasts for approximately 10
seconds.)
3. When Lumen 1000 enters pairing mode, press and hold button on
LinkStream for 5 seconds placing it into paitinr mode.
4. When pairing is complete the beeping in the Lumen 1000 will stop and
it will start receiving audio from the LinkStream device.
a. Typical use scenarios (sketch with stickfigures)
b. Describe IPODA with PICTURE showing labels identifying components
flexstream Device Illustration
Device Description
1 flexstream Unit
2 Mic Cover
3 Mic Ports
4 Docking Connector
13
5 Lasermarking Area
c. How to use APP (including pairing)
i. Default mode -TBD
ii. Table capturing pairing scenarios – In process
Troubleshooting section pointing to sections within manual
14
FCC LABEL REQUIREMENTS
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation. (REF only
- PER 15.19(a)(3))
• Changes or modifications not expressly approved by IntriCon for compliance could void the
user’s authority to operate the equipment. (REF only – per 15.21)
• This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
a. Reorient or relocate the receiving anten na. I nc rease the separation between t he
equipment and receiver. Connect the equipment into an out l et on a circuit different
from that to which the receiver is connected. Consu lt t he dealer or an experienced
radio/TV technician for hel p. ( RE F only – per 15.105)
15
Loading...